novostella NTS22A LED RGB Light Strip User Guide

LED RGB Light Strip User Guide

THANK YOU for choosing Novostella. To optimize user experience, please use the product according to the following instructions.
Warning

1. Winding lighting is prohibited, as it affects heat dissipation and might cause dangers.
2. Please unroll the light strip from the plate before lighting it up.
3. NTS22A-RGB-US-NF can only work with ONE power adapter in a series connection of a maximum of 6 meters, and NTS28A-RGB-US-NF can only work with ONE power adapter in a series connection of a maximum of 12 meters.
4. Please check if the light strip and the parts are intact before using them.
5. Please make sure that the power supply is turned off before installation.
6. Please use the attached power adapter only, to ensure that the light works properly.
7. Please do not use this light in the open air or in a humid environment.

Specification

1, LED Signal Receiver x 1
Frequency Range| 2402MHz to 2480MHz
EIRP| 4.08dBm
Wireless Application Protocol| BLE
P/N| NTS28A-RGB-US-NF
---|---
Model| NTS28A-RGB-US-NF
Wattage| 18W
Color| RGB
Total Length| 40ft / 12m
LED Type| 5050
LED Quantity| 336 LEDs
Input Voltage| 100-240V AC
Frequency| 50/60Hz
Luminous Flux| 38lm/m (Red: 61m/m Green: 251m/m Blue: 71m/m)
Adapter| 24W(24V1A)
Working Voltage| 24V
Working Temperature| -25°C-40°C
Restriction| IP20, Indoor Use Only, DRY LOCATIONS ONLY
Battery Type| CR2025 (for RF remote controller)
Package Includes| Light Strip x 1, RF Remote Controller x 1,
Power Adapter x 1, LED Signal Receiver x 1
Frequency Range| 2402MHz to 2480MHz
EIRP| 4.08dBm
Wireless Application Protocol| BLE

Components

Note: Power Adapter Cord – type Z attachment. For type Z attachment: The cable or cord cannot be replaced without breaking or destroying the luminaire.
LED Signal Receiver

RF Remote Controller

Dynamic Mode
There are 6 preset dynamic modes, and their speed can be adjusted with the “QUICK” or”SLOW” button.

1. JUMP3: Flash and loop among 3 colors (Red, Green, Blue).
2. JUMP7: Flash and loop among 7 colors (Red, Green, Blue, Yellow, Purple, Cyan, and White).
3. FADE3: Fade and loop among 3 colors (Red, Green, and Blue).
4. FADE7: Fade and loop among 7 colors (Red, Green, Blue, Yellow, Purple, Cyan, White).
5. FLASH: Flash on white color only.
6. AUTO: Loop among the above 5 dynamic modes. The FLASH mode (white color only) repeats 20 times, while the rest four modes repeat 4 times in each loop.

Three Settings
There are three flexible settings for the remote controller(s) to control the light strip(s) as per your lighting project, One-to-One Setting, One-to-Many Setting, and Many-to-Many Setting. You can choose either which light strip and how many lights strips one controller controls, or which controller and how many controllers control the light strip(s).

1. One-to-One Setting: One remote controller can only control one light strip. Turn on the remote controller and power on the LED Signal Receiver of the light strip. During the first 5 seconds, immediately long-press the bottom left button on the remote controller till the strip light blinks. Then the ‘One-to-One Setting’ is done. One-to-One Setting is the factory default.
2. One-to-Many Setting: If you want to control many light strips with one remote controller, you could choose the ‘One-to-Many’Setting. Turn on the remote controller and power on all LED Signal Receivers of the light strips. During the first 5 seconds, immediately long-press the bottom left button on the remote controller till the strip lights blink. Then the ‘One-to-Many Setting’ is done.
3. Many-to-Many Setting: If you have many light strips and remote controllers, and hope that any of the controllers can control all the light strips, you could choose the ‘Many-to-Many’ Setting. Turn on each remote controller and power on its LED Signal Receiver. During the first 5 seconds, immediately long-press the bottom right button on the remote controller till the strip light blinks.

How to DIY colors?
This light strip is made of RGB LEDs, which means there are three colors (red/green/blue) on one LED. All lighting colors are made by changing the ratio of red, green, and blue on the LED. e.g. Red + Green = Yellow Lighting Red + Blue = Purple Lighting Green + Blue = Cyan Blue Lighting Firstly, choose and press one button from DIY1 to DIY6 on the RF controller, for instance, the DIY1 button. Secondly, press the ↑ or ↓, button to increase (↑) or decrease (↓) the ratio of red, green, and blue on the LED, so as to create different lighting colors. Then the specific DIY color lighting will be saved on the DIY1 button (the button you choose in the first step). Next time when you want to use this DIY color lighting, simply press the DIY1 button for quick access.

Installation

1. How to cut the LED strip?
Before cutting the LED strip, please keep these in mind.

1. Once the strip is cut, an extra connector is needed for reconnection, otherwise, the rest part being cut can not work. The connector is not included in the package. You may contact the seller for the connector details.
2. Double confirm the length for installation before making the cut.
3. Cut the strip along the marks.
   

2. How to install the LED strip?

1. Choose an even and smooth surface.
   

2. Sweep the dust off the surface.

3. Tear the back sheet.
   

4. Press the strip with force.

5. Fasten the strip with clips, if applicable. (It is recommended to use the clip every 0.5m.)
   

6. Connect the light strip ®to the controller cable and then connect the controller cable to the power adapter ®. Plug the adapter into the socket and turn on the light strip by pressing the ‘ON’ button on the RF remote controller.
   

Note:

1. If the strip can’t light up after the installation, please check whether the joints are connected correctly.
2. Please make sure to turn off the power supply during routine maintenance.
3. To avoid any damage to the strip, please do not use chemical solvent during routine maintenance.

How to control the light strip?

4.1 Download the App Lotus Lantern by scanning the QR code below. This App is compatible with Android 4.0 and iOS 8.1 or above.
Download APP
1: Scan the QR code from the label or user manual.

http://www.easytrack.net.cn/download/170CAILANGUANGDIAN

The APP is compatible with Android 4.0 and Los 8.1 and higher versions.

4.2 Power on the light.
4.3 Activate the Bluetooth function on your phone and open the App to automatically connect to the light.
4.4 Enjoy the lighting by exploring the functions such as brightness, modes, music sync, timer etc via the App.

FCC ID(Remote Controller): 2AWON-NTS-RGB-RF
FCC ID(BT Signal Receiver): 2AWON-NTS-RGB-BT
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For Signal Receiver:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator& your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>