novostella NTF72 Smart LED Flood Light User Guide

: June 5, 2024
: novostella

Table of Contents

novostella NTF72 Smart LED Flood Light
Part One – How to insall the light
Parameters
Installation
Limitations of Indoor and Outdoor Use
Contact Us
Read User Manual Online (PDF format)
Download This Manual (PDF format)

novostella NTF72 Smart LED Flood Light

Thank you for ordering from Novostella. Set-up is easy and takes only a few minutes by following the instructions.

Part One – How to insall the light

Warning

Please check if the light and the parts are intact before installation.
Make sure to cut off power before installation.
Please do not place this light in corrosive conditions.
If there is any damage to the cord, please cut off the power and stop using it immediately.
Please do not retrofit the light within the warranty period.
To ensure the light works properly, please use the voltage indicated on the packing.

Parameters

Components

Note Cord – type Y attachment.
For type Y attachment: If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer of his service agent or a similar qualified person in order to avoid a hazard.

Dimension

Installation

Step A: According to the spacing of two screw bits on the bracket, drill two holes on the mounting panel.
Step B: Aim the bracket at the holes and fix it with two bolts.
Step C: Adjust the lighting direction up or down as per your need and plug in to power the light on.

Note:

01 Make sure that the distance between the light and the object being lits is more than 1 meter, so as to avoid high temperature caused by short distance. The light source of this luminaire is not replaceable.

Limitations of Indoor and Outdoor Use

This light is waterproof and dampproof. It is protected against rain, but it cannot be immersed in water.
The mounting position of this light should be able to bear at least 10 times as heavy as the light.
This light should be used in a condition that is good for heat dissipation. Its working temperature should be less than 45°C Too high the working temperature will cause serious lumen depression and affect the lifespan of the light.

FCC ID: 2AWONNTF71
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Part Two – How to pair the light to Smart Life app?

Before starting the paring, please make sure to turn on the Bluetooth on your phone, and connect to the Internet.
Step A: Smart Life app installation
Please choose either way below to download and install the app.

As per your phone system, choose the QR code to scan.
Search keyword ‘Smart Life’ in Apple Store of Google Play.

Step B: Create an account on Smart Life and login.
Note: Please keep your account and password in mind for Alexa or Google Assistant APP pairing later.

Step C: Add the light to Smart Life App

Tap ‘+’ button on top right corner to add devices. Tap ‘Lighting’, then choose ‘Light Source {BLE)’ to add the lights.
Power on the light with your own switch. Repeatedly turn the on-off-on-offon-off-on switch to activate the light into rapid blinking status (about O.Ss per blink). Please make sure to keep an interval over 2 seconds between each turn-on and turn-off. Then click the ‘Next’ button on this page. Find the lighting devices and click’+’.
Give a name to the light.
Note: A simple name is recommended.
The named light will be shown on the app homepage. Now you can control the light (turn on/off, change colors, adjust brightness ect.) with Smart Life on the setting page. Turn on or off the light by tapping the bulb icon.

How to group the lights?

Make sure all the lights have been paired to “Smart Life” app, then group the lights by following these steps.

Choose any light on the app, click the edit button on the top right corner, then click “Create Group”
Choose the lights you want to group from the device list and rename the group.

Part Three – How to connect the lights to the Internet, and control with Amazon Alexa and Google Assistant?
If you want to connect the lights to the Internet, and control with Amazon Alexa and Google Assistant, you can easily expand the smart floodlights with our Hub accessory (sold separately).
Please click the below link to purchase the Hub accessory from our shop:
US: https://www.amazon.com/dp/B08WXBLN3G
UK: https://www.amazon.co.uk/dp/B08WKWMMFR
After you get the Hub accessory, please follow below steps to setup:
Step A: WiFi connection, pair the Hub to Smart Life App.

Please turn on the WiFi on your phone. The hub only supports 2.4GHz WiFi network, not 5.0GHz. Please make sure your working network is 2.4GHz and your router has disabled the MAC filter. It is strongly recommended to place the hub to somewhere that is between the lighting devices and the router, and make sure it responds well to the WiFi signal.

Tap ‘+’ button on top right corner to add device. Tap ‘Gateway Control’, then choose ‘Wireless Gateway (BLE)’ to add the hub.
Plug the hub into a socket. Long press the power button on the hub till the indicator lights rapidly blink, tap the ‘Next ‘ button, then click ‘+’ button to add the hub.
Choose your WiFi network, enter your password, and tap the ‘Next’ button. Give a name to the hub and tap the ‘Done’ button.

Step B: Add the lights to the Hub.
Please make sure all the lights have been paired to ‘Smart Life’ App first. Choose the hub on the app, click the ‘add device by list’ button, select all the lights, and click the ‘Confirm’ button.

How to control the light with Amazon Alexa?
Please make sure that your Alexa app is connected to Echo, and both work well under your WiFi network.
Step A: Log in your Alexa App, tap top left corner, and tap ‘Skills’.

Step B: Type ‘Smart Life’, find ‘Smart Life’ from the search result and tap it to enable the skill.

Step C: Enter your Smart Life App account and password. Tap ‘Link Now’, then tap ‘Authorize’ on the next page to bind Smart Life account to Alexa.
Step D : When your Smart Life account is bound to Alexa, tap ‘DISCOVER DEVICES’ to detect the light.

Step E: When the named light is paired to Alexa from Smart Life, it will show on the device page (see the ‘smart light’ example).

Step F: Now you can control the light with Alexa App on the setting page. To turn on or off the light, simply tap the bulb icon.
Step G: You can also voice control the light with Alexa by giving these commands: “Alexa, turn on ‘device name’ “, “Alexa, set ‘device name’ to ‘color'”, “Alexa, set ‘device name’ to ‘number'”. The device Name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “Alexa, turn on ‘smart light'”, “Alexa, set ‘smart light’ to ‘blue'” etc.

How to control the light with Google Assistant?
Step A: Login Google Assistant App, tap ‘Home Control’ on the left sidebar page.
Step B: Tap’+’ button on the bottom right to enter next page.
Step C: Find ‘Smart Life’ from the sidebar list.

Step D: Enter your Smart Life App account and password to bind your Smart Life account to Google Assistant.
Step E: You will find the named light shown on the Home Control page. Now you can control the light on Google Assistant App, or voice control it by giving these commands: “ok Google, turn on ‘device name’ “, “ok Google, set ‘device name’ to ‘color'”, “ok Google, set ‘device name’ to ‘number'”.
The Device Name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “ok Google, turn on ‘smart light'”, “ok Google, set ‘smart light’ to ‘blue’ ” etc.