novostella HP24L-1202000-AVU-S LED RGB Light Strip User Guide

HP24L-1202000-AVU-S LED RGB Light Strip
User Guide

THANK YOU for choosing Novostella. To optimize the user experience, please use the product according to the following instructions.
Warning

1. Winding lighting is prohibited, as it affects heat dissipation and might cause dangers.

2. Please unroll the light strip from the plate before lighting it up.

3. 0133322-RGB-US-NF can only work with ONE power adapter in a series connection of a maximum of 6 meters, and UT33328-RGB-US-NF can only
   work with ONE power adapter in a series connection of a maximum of 12 meters.

4. Please check if the light strip and the parts are intact before using them.

5. Please make sure that the power supply is turned off before installation.

6. Please use the attached power adapter only, to ensure that the light works properly.

7. Please do not use this light in the open air or in a humid environment.

Specification

1,
LED Signal Receiver x 1, Mounting bracket x 12
SKU| UT33328-RGB-US-NF
---|---
Model Number (Power Adapter)| HP36A-1203000-AU
Wattage| 36W
Color| RGB
Total Length| 40ft / 12m
LED Type| 5050
LED Quantity| 360 LEDs
Input Voltage| 100-240V AC
Frequency| 50/60Hz
Working Voltage| 12V
Working Temperature| -25°C-40°C
Restriction| Indoor Use Only
Battery Type| CR2025 (for RF remote controller)
Package Includes| Light Strip x 2, RF Remote Controller x 1, Power Adapter x 1,
LED Signal Receiver x 1, Mounting bracket x 24

Components

Note. Power Adapter Cord – type Z attachment. For type Z attachment: The cable or cord cannot be replaced without breaking or destroying the luminaire.

LED Signal Receiver (UT33322-RGB-US-NF)

LED Signal Receiver (UT33328-RGB-US-NF)

RF Remote Controller

Dynamic Mode

There are 6 preset dynamic modes, and their speed can be adjusted with the “QUICK” or”SLOW” button.

1. JUMP3: Flash and loop among 3 colors (Red, Green, Blue).
2. JUMP7: Flash and loop among 7 colors (Red, Green, Blue, Yellow, Purple, Cyan, White).
3. FADE3: Fade and loop among 3 colors (Red, Green, Blue).
4. FADE7: Fade and loop among 7 colors (Red, Green, Blue, Yellow, Purple, Cyan, White).
5. FLASH: Flash on white color only.
6. AUTO: Loop among the above 5 dynamic modes. The FLASH mode (white color only) repeats 20 times, while the rest four modes repeat 4 times in each loop.

Three Settings

There are three flexible settings for the remote controller(s) to control the light strip(s) as per your lighting project, One-to-One Setting, One-to-Many Setting, and Many-to-Many Setting. You can choose either which light strip and how many lights strips one controller controls, or which controller and how many controllers control the light strip(s).

1. One-to-One Setting: One remote controller can only control one light strip. Turn on the remote controller and power on the LED Signal Receiver of the light strip. During the first 5 seconds, immediately long-press the bottom left button on the remote controller till the strip light blinks. Then the ‘One-to-One Setting’ is done. One-to-One Setting is the factory default.
2. One-to-Many Setting: If you want to control many light strips with one remote controller, you could choose the ‘One-to-Many’Setting. Turn on the remote controller and power on all LED Signal Receivers of the light strips. During the first 5 seconds, immediately long-press the bottom left button on the remote controller till the strip lights blink. Then the ‘One-to-Many Setting’ is done.
3. Many-to-Many Setting: If you have many light strips and remote controllers, and hope that any of the controllers can control all the light strips, you could choose the ‘Many-to-Many’ Setting. Turn on each remote controller and power on its LED Signal Receiver. During the first 5 seconds, immediately long-press the bottom right button on the remote controller till the strip light blinks.

How do DIV colors?

This light strip is made of RGB LEDs, which means there are three colors (red/green/blue) on one LED. All lighting colors are made by changing the ratio of red, green, and blue on the LED.
e.g. Red + Green = Yellow Lighting
Red + Blue = Purple Lighting
Green + Blue = Cyan Blue Lighting

Firstly, choose and press one button from DIY to DIY6 on the RF controller, for instance, the dial button. Secondly, press↑ or ↓ button to increase (↑)or decrease (↓) the ratio of red, green, and blue on the LED, so as to create different lighting colors. Then the specific DIY color lighting will be saved on the DIY button {the button you choose in the first step). Next time when you want to use this DIY color lighting, simply press the DIY button for quick access.

Installation

How to cut the LED strip?
Before cutting the LED strip, please keep these in mind.

1. Once the strip is cut, an extra connector is needed for reconnection, otherwise, the rest part being cut can not work. The connector is not included in the package. You may contact the seller for the connector details.
2. Double confirm the length for installation before making the cut.
3. Cut the strip along with the marks.

How to install the LED strip?

1. Choose an even and smooth surface.
2. Sweep the dust off the surface.
3. Press the strip with force.
4. Tear the back sheet.
5. Fasten the strip with clips, if applicable. (It is recommended to use the clip every 0.5m.)
6.  Connect the light strip 1 to controller cable 2 , and then connect the controller cable to the power adapter 3. Plug the adapter into the socket and turn on the light strip by pressing the ‘ON’ button on the RF remote controller. Note:
   (1) If the strip can’t light up after the installation, please check whether the joints are connected correctly.
   (2) Please make sure to turn off the power supply during routine maintenance.
   (3) To avoid any damage to the strip, please do not use chemical solvent during routine maintenance.

Contact Us
Have some issues? No worries! Please reach us via these channels. Our customer services team is more than happy to help.

support@novostella.net
fb.com/novostella.fans
www.novostella.net
Scan to Message Now!

Manufacturer: Shenzhen Ustellar Technology Ltd.
Address: Rm.201, A Bldg., No. A Qianhai 1st Rd., Shen’gang Cooperation Zone,
Qianhai, Shenzhen, CHINA 518000

support@novostella.net
fb.com/novostella.fans
www.novostella.net

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>