hippo digital M10D Smart Wireless Microphone User Manual
- June 9, 2024
- hippo digital
Table of Contents
Wireless Microphone
User Manual
Introduction
Thanks for choosing our product.
This product is a smart wireless microphone that provides professional-grade
recording output. Plug and play, no app required. Multiple uses: It can be
used in online live broadcast, video Vlog shooting, program interview,
recording, video teaching and other occasions.
The wireless Microphone consists of two parts, one is Microphone transmitter ,
the other one is receiver. (See as below picture)
ID Diagram
1. Windproof net ,
2. Microphone indicator
3. Microphone charging port
4. Microphone clip| 5. Switch key .
6. port to connect phone
7. Receiver indicator
8. port of receiver
---|---
- The function of above ⑧ will be specifically explained later.
Some Android phones may have incompatibility problems due to system , please consult your dealer for details
How to use
Step 1: Connect the receiver to phone with port.
Note: oppo / vivo /iqoo /realm brand mobile phones can be used normally
only when they go to the settings (search “OTG” – turn on OTG power supply)
Step 2: Press switch key of microphone, the indicator light turns green, and
then power is turned on.
Step 3: The indicator light of receiver keeps always on, then open the phone camera, live App or other Apps , and then to use the microphone to receive sound.
Special Note:
For the use of ⑧ port : there is no battery in receiver , and no need to
recharge during live. If the phone is low power during Live, it can be
recharged directly through ⑧ port.
About UI
Microphone Transmitter
| Function | How to use | Light |
|---|---|---|
| Power on | Press switch key once | Green light on |
| Power off | Press switch key about 3 seconds | Light off |
| Pairing | Red and green flash alternately | |
| Paired | Green light keeps on | |
| Pause /Recovery | Press switch key once | The green light flashes slowly during |
pause
Low battery alarm| Power on state| The red and green lights come on every 10
seconds
Charging| Charging with cable| The red light goes out when it is fully charged
Receiver
| Function | How to use | Light |
|---|---|---|
| Power on | Plug in the device | light on |
| Power off | Plug off the device | Light off |
| Pairing | light , slow | |
| Paired | The light’s |
REVERB MODE: Press the START BUTTON 3 times continuously to enter reverb mode
Product support and listening function “
This product comes with Al noise reduction, which will enter the noise
reduction mode when it is started
Packing List
Content of packing
- Microphone transmitter
- receiver
- charging cable
- User manual
FCCID: 2ASJU-M10D
RF exposure statement
This equipment complies with the FCC radiation exposure limits set forth for
an uncontrolled environment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
MADE IN CHINA
Documents / Resources
|
hippo digital M10D Smart Wireless
Microphone
[pdf] User Manual
M10D, 2ASJU-M10D, 2ASJUM10D, M10D Smart Wireless Microphone, Smart Wireless
Microphone, Wireless Microphone, Microphone
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>