novostella NTA11W Solar Security Light User Guide
- June 5, 2024
- novostella
Table of Contents
Solar Security Light
User Guide
Thank you for ordering from Novostella. Set-up is easy and takes only a few minutes by following the instructions.
Safety Information
- Your motion light is not a toy. Keep it out of reach from small children.
- Your motion light and solar panel are both weather-resistant.
- You can mount your motion light indoors, but your solar panel must be installed outdoors to receive light from the sun.
- If using a step ladder, you may require another person to help you install the
- Prior to installation, lay out all components and check against the part list section in this manual.
- Do not look directly at the light when it is on.
Parameters
| P/N | NTA11W-CW-US-1 |
|---|---|
| Model | NTA11 |
| Max Luminous Flux | 18001m |
| Color temperature | 3000K/4500K/6000K Selectable |
| Battery Type | Li-ion 3.7V/2000mAhx2 |
| Solar Panel | Amorphous Silicon: 165*133mm |
| Cable Length | 15ft/4.5m |
| Max Detection Range | 180° |
| Max Detection Distance | 70ft/21m |
| Lighting Time | 30s/60s/120s Adjustable |
| Material | ABS+PC |
| Waterproof Rating | IP65 |
| Working Temperature | -20°C-40°C |
Components
Dimension
Installation
CARE & MAINTENANCE
- From time to time, ensure the plug between the solar panel and light is securely connected.
- It is advisable to adjust the angle of the solar panel to optimize the exposure of the sun during the winter months.
- The solar panel should be cleaned with a damp cotton cloth on a regular This will ensure optimal performance and battery charging. Periodically, utilize the same technique to clean the lenses of the motion lights.
- Never let any abrasive material come into contact with the solar panel.
PREPARATION
- Recommended Tools: Power Drill, Phillips Screwdriver
- Ensure your solar panel is placed where exposes to optimized sunlight. Be aware of objects such as trees or property overhangs that may impede the panel’s ability to generate a charge.
- Recommended Install Height: 6.5-8.25 feet above the ground.
-
Use a power drill (not included) to create the holes on your chosen mounting surface. Use 4 of the included wall plugs and screws to fasten the solar panel to the surface.
-
Use a power drill (not included) to drill the holes on your chosen mounting surface. Place the mounting plate ( with smooth suface facing out) over the holes & use 4 of the included wall plugs and screws to fasten the mounting plate to the surface.
-
Buckle the motion light into the mounting plate securely.
-
Connect the wire from the solar panel into the socket located under the light fixture. Your solar motion light will now begin to charge.
Functions
TIME:
TEST: It is used to test for installation, which is not controlled by
ambient lux, and the light will stay on for 5 seconds.
305: Recommended. Only work at night. Determines the duration of the
light once motion is detected: 30 seconds.
60S: Only work at night. Determines the duration of the light once motion
is detected: 90 seconds.
120S: Only work at night. Determines the duration of the light once
motion is detected: 120 seconds.
Ca:
3000K: Set the color temperature to 3000K.
4500K: Set the color temperature to 4500K.
6000K: Set the color temperature to 6000K.
MODE:
AUTO: Recommended. Only work at night. Auto ON for a pre-determined
time (the 30S/60S/120S) when people or other living objects are detected
within the sensing area, and Auto OFF after no further motion is detected.
OFF: Turn OFF the light.
ON: The ON position acts to override the motion activation function. This
will allow a limited period of constant illumination.
Note:
- Prior to using your solar motion light, the solar panel needs to be connected to the light for a period of three days. This initial charge should be done in the OFF position. After the third day, your included batteries will be enough power for the operation of solar motion light. Place the light in the AUTO position.
- The sensor will be more sensitive to motion across than motion towards it directly.
Frequently Asked Questions
Q: Where should the solar panel be mounted?
A: Mount your solar panel in a position that will enable the most amount of
light to be absorbed. In the Northern Hemisphere this is usually south facing.
CI: Does the solar panel require the direct sun to charge?
A: The solar panel can charge the internal batteries in direct and indirect
light. For best results, try to optimize your solar panel’s sun exposure.
CI: Can additional or extended cable wire for the solar panel be purchased?
A: At this point, there are no extensions available for the cable that
connects the light to the solar panel.
Q: Why does the solar motion light appear to “strobe” or flash?
A: A rapidly flashing light is caused by undercharged batteries. Turn the
solar motion light’s switch to the”OFF” position and charge for three full
sunny days to bring the batteries to full charge. After three days, turn the
switch to the “AUTO” position.
Q: Will decorative or street lights have an effect on the motion sensors’
ability to operate?
A: Yes, the sensor of the solar motion light is light-sensitive. For nighttime
usage, ensure no other light activates the motion sensor.
Contact Us
Have some issue? No worries! Please reach us via these channels. Our customer
services team is more than happy to help.
support@novostella.net
@novostella.lighting
fb.com/novostella.fans
Scan to Message Now!
www.novostella.net| 
---|---
Manufactured by Shenzhen Ustellar Technology Ltd. Address: Rm 201, 2/F, Block A, No.1 Qianwan 1st Avenue, Shenzhen, P.R.China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>