novostella NTS29-CW-NF Tunable White LED Light Strip User Guide

NTS29-CW-NF Tunable White LED Light Strip
User Guide

THANK YOU for choosing Novostella. To optimize user experience, please install and use the light according to the following instruction.
Warning

1. Winding lighting is prohibited, as it affects heat dissipation and might cause dangers.
2. Please unroll the light strip from the plate before lighting it up.
3. Light strips of different length (6m/12m) require different power (12V 2A/24V 1A). To ensure it works properly, the light strip can not be extended and must keep the total installation length within its maximum (6m/12m).
4. Please check if the light strip and the parts are intact before using them.
5. Please make sure that the power supply is turned off before installation.
6. To ensure that the light works properly, please use the voltage indicated on the packing.
7. Please do not use this light in the open air or in a humid environment.

Specification

Controller Cable x 1, Power Adapter x 1,
Fastener x 12
SKU| NTS29-CW-NF
---|---
Wattage| Max.24W
LED Quantity| 1440 LEDs
Color Temperature| 3000K+6000K
Color| Warm White + Cool White
Working Voltage| 24V DC
Input Voltage| 100-240V AC
Protection Rating| IP20
Frequency| 50/60Hz
Length| 12m/40ft
LED Type| 2835
Beam Angle| 120°
Working Temperature| -25°C-40°C
Battery for Remote Controller| AAA*2(Not Included)
Package Includes| Light Strip x 1, RF Remote Controller x 1,
Controller Cable x 1, Power Adapter x 1,

Components

Installation

How to cut the LED strip?
Before cutting the LED strip, please keep these in mind.

1. Once the strip is cut, an extra connector is needed for reconnection, otherwise, the rest part being cut can not work. The connector is not included in the package. You may contact the seller for the connector details.
2. Double confirm the length for installation before making the cut.
3. Cut the strip along with the marks.

How to install the LED strip?

1. Choose an even and smooth surface.
2. Sweep the dust off the surface.
3. Press the strip with force.
4. Tear the back sheet.
5. Fasten the strip with clips, if applicable. (It is recommended to use the clip every 0.5m.)
6.  Connect the light strip to controller cable 0, and then connect the controller cable to power adapter ®. Plug the adapter into the socket and turn on the light strip by pressing the ‘ON’ button on the RF remote controller. Note:
   (1) If the strip can’t light up after the installation, please check whether the joints are connected correctly.
   (2) Please make sure to turn off the power supply during routine maintenance.
   (3) To avoid any damage to the strip, please do not use chemical solvent during routine maintenance.

Instructions on RF remote controller.

The remote controller can control either one strip or many strips under different settings.

1. One-to-One Setting: one remote controller can control only one light strip. When the controller is on, during the first 5 seconds, immediately long-press the bottom left button till the strip blinks, which means the “One-to-One” setting is done.
2. One-to-Many Setting: one remote controller can control two or more light strips. When the controller is on, during the first 5 seconds, immediately long-press the bottom right button till the strip blinks, which means the “One-to-Many” setting is done.

Contact Us
Have some issues? No worries! Please reach us via these channels. Our customer services team is more than happy to help.

support@novostella.net
fb.com/novostella.fans
www.novostella.net
Scan to Message Now!
@novostella lighting
youtube.com/c/novostella
Manufacturer by Shenzhen Ustellar Technology Ltd.
Address: Rm 201, 2/F, Block A, No.1 Qianwan 1st Avenue, Shenzhen,
P.R.China

support@novostella.net
fb.com/novostella.fans
www.novostella.net
@novostella lighting
youtube.com/c/novostella

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>