XTOOL D1 Pro Updated Laser Engraver Cutter User Guide

: June 19, 2024
: XTOOL

Table of Contents

D1 Pro Updated Laser Engraver Cutter
Unbox and check
Assemble xTool D1 Pro
Meet your xTool D1 Pro
Download and install software
Use Rotary Attachment 2
Level reference
Use the support module
Set the support module
Clean the laser module
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quick Start Guide
D1 Pro D1.1.2_KD010623000

D1 Pro Updated Laser Engraver Cutter

THANK YOU!
Dear xTooler:
Thank you for purchasing xTool D1 Pro. We are so grateful for your recognition, and sincerely hope you will enjoy this product!
xTool D1 Pro is a high-accuracy and high-power laser engraver and laser cutter. From novice to expert, f rom home use to business, xTool D1 Pro is ready to give you the best laser engraving & cutting experience.
Our mission is to make it easier for everyone to create with our machine.
We attach great importance to product experience and user suggestions.
Please let us know if you have any questions anytime. We are always here to help. You can join our facebook group which gathers 25000+ innovators like you, to share creative ideas and get inspired by others.
By visiting our online store, you can also ﬁnd our latest accessories and various materials to maximize the magic of xTool D1 Pro.
Thanks again for your support, and we will consistently provide quality products and services in the future.
Sincerely,

Ofﬁcial Website: www.xtool.com
Facebook Group: xTool D1 Ofﬁcial Group / Makeblock xTool Ofﬁcial Group
Support Center: support.xtool.com
Technical Support: support@xtool.com

xTool D1 Pro provides two color options. This user manual uses the golden red version to describe how to assemble and set up your machine.

Unbox and check

The secret to getting ahead is getting started.
Are you ready to embark on a creative journey?
Let’s go!

Assemble xTool D1 Pro

You can visit support.xtool.com or scan the QR code to ﬁnd the tutorial video.

The screws are used to set the tension of the timing belts. Do not fully tighten them. Otherwise, the timing belts may be damaged.

If you can’t put the shaft through the timing belt, the possible cause is that the timing belt is set too tight. You can adjust its tension by turning the screw.

Keep a small distance between the coupling and the motor, or the coupling can’t rotate properly or emit noises.

Slide the two sliders down against the front plate.

Fully tighten the two screws.

Pay attention to the front and back sides of the connector. Insert it properly.

No scissors are included in the pack.

The screw is used to set the tension of the timing belt. Do not fully tighten it. Otherwise, the timing belt may be damaged.

80% done!
Excited to see your laser cutter begins to take shape!
Success is just around the corner!

Use the thumb screw to ﬁt the laser module

You may need to repeat this process multiple times to tighten the thumb screw.

Use the thumb screw

If the handle is blocked, you can tighten or loosen the screw as follows.

Insert the TF card before using xTool D1 Pro. Otherwise, some functions may fail, such as Wi-Fi connection-based processing, ofﬂine processing, and Framing in processing preview.

Congratulations!
You have completed the installation!
We’ve got a little surprise in our software to make your ﬁrst project creative and memorable.
Download the software and get the novice task!

Meet your xTool D1 Pro

Set up xTool D1 Pro
Adjust the tension of the timing belts

Set the position of the laser module

To cut thicker materials, you can adjust the position of the rear plate on the laser module, based on the scale with which the focal length setting bar is aligned, to ensure better cutting performance.

For the 20 W laser module

For the 40 W laser module

Tips: The settings are tested under a laboratory environment and are for reference only. The setting may vary according to material, so it is recommended you test the materials before starting to process.

Download and install software

You can download xTool Creative Space (XCS) at our ofﬁcial website xtool.com or use the third-party software LightBurn to operate xTool D1 Pro.
Note: You need to purchase LightBurn before using it.

Create with example projects

Before starting your creation, you are advised to test the parameter settings and engraving performance ﬁrst to prevent waste of materials.
For example, you can engrave on an area near the edge of a material to see the engraving performance. For valuable items, especially, you can engrave on a substitute for testing.

https://support.xtool.com/hc/en-us/articles/5662836045975

xTool D1 Pro is delivered with a material pack that allows you to start your creation.
Scan the QR code to ﬁnd example projects and tutorials.
Alternatively, you can click Support on xTool Creative Space (XCS) and then choose xTool D1 Pro > xTool D1 Pro Example Project Files & Tutorials. You can download the example projects and follow the instructions to create your ﬁrst works.

Before creating your works, you can place the aluminum sheet in the working area of xTool D1 Pro to protect your desk or ﬂoor from being smoked or burned.

If the aluminum sheet is not ﬂat due to ﬁlm removing, you can use masking tape to stick it on your desk or ﬂoor.

Use Rotary Attachment 2

You can connect xTool D1 Pro to Rotary Attachment 2 to engrave cylindrical or irregular materials.
Rotary Attachment 2 needs to work with a device and software.
For details about how to use it, visit support.xtool.com.

Place Rotary Attachment 2 parallel to the working area of xTool D1 Pro.
Before you connect it to xTool D1 Pro , you may need to set its level based on the diameter of the material to be processed.

Level reference

Set the level
Use the changing of the level from C to B as an example.

Use the support module

The support module is applicable to the processing of irregular objects or objects that are too long for Rotary Attachment 2.

You can place the support module as required.

Set the support module

Turn the knob clockwise to move the support wheels upward

Turn the knob counterclockwise to move the support wheels downward

Clean the laser module

For the 20W laser module, you are advised to clean it, including the inner and outer frames of the light shield, lens, and red light outlet, every time after it has been used for one consecutive hour.

When the light shield is dirty or laser beams can’t cut a material, you need to clean the laser module.

Turn off the device and remove the laser module from the device.
Remove the nozzle and its connector from the laser module.
Clean the inner and outer frames of the light shield with tissues or dust-free cloth moistened with alcohol; and clean the lens and red light outlet with a cotton swab moistened with alcohol.