FUJITSU FWM7BTZ61 Bluetooth Dual Mode Module Instructions
- June 9, 2024
- FUJITSU
Table of Contents
FUJITSU FWM7BTZ61 Bluetooth Dual Mode Module
Instruction
This is the Bluetooth® Dual mode module FWM7BTZ61
The pin assignments and Function of this module are listed in the table. Mount
the module according to the table below. 
< TOP View>
Pin name| No| I/O| Function| External
Connection
---|---|---|---|---
GND| 1| –| Ground| Ground
P13
|
2
|
I/O
|
I2C SCL
| SCL pin of Auth 3.0 CP
with pull-up
P12| 3| I/O| Programmable I/O| NC when not in use
P11
|
4
|
I/O
|
I2C SDA
| SDA pin of Auth 3.0 CP
with pull-up
P9| 5| I/O| Programmable I/O| NC when not in use
P14| 6| I/O| Programmable I/O| NC when not in use
NC| 7| –| NC| NC
NC| 8| –| NC| NC
Pin name| No| I/O| Function| External
Connection
---|---|---|---|---
P6| 9| I/O| Programmable I/O| NC when not in use
P29| 10| I/O| Programmable I/O| NC when not in use
P26| 11| I/O| Programmable I/O| NC when not in use
P28| 12| I/O| Programmable I/O| NC when not in use
P4| 13| I/O| Programmable I/O| NC when not in use
GND| 14| –| Ground| Ground
VBAT| 15| –| Power supply| DC power supply
GND| 16| –| Ground| Ground
PUART_TX
|
17
|
O
| UART data output
(For command / data communication)
|
UART RxD
PUART_RX
|
18
|
I
| UART data input
(For command / data communication)
|
UART TxD
PUART_RTS
|
19
|
O
| UART Request To Send
(For command / data communication)
|
UART CTS
PUART_CTS
|
20
|
I
| UART Clear To Send
(For command / data communication)
|
UART RTS
NC| 21| –| NC| NC
RESET#| 22| I| Reset input (Active Low)| RESET
GND| 23| –| Ground| Ground
HUART_RX
|
24
|
I
| UART data output
(For HCI or Firmware writing)
|
NC (*1)
HUART_CTS
|
25
|
I
| UART data input
(For HCI or Firmware writing)
|
NC (*1)
HUART_RTS
|
26
|
O
| UART Request To Send output
(For HCI or Firmware writing)
|
NC (*1)
HUART_TX
|
27
|
O
| UART Clear To Send input
(For HCI or Firmware writing)
|
NC (*1)
GND| 28| –| Ground| Ground
GND| 29| –| Ground| Ground
Pin name| No| I/O| Function| External
Connection
---|---|---|---|---
GND| 30| –| Ground| Ground
VDDIO| 31| –| I/O Power supply| DC power supply
GND| 32| –| Ground| Ground
NC| 33| –| NC| NC
GND| 34| –| Ground| Ground
NC| 35| –| NC| NC
GND| 36| –| Ground| Ground
NC| 37| –| NC| NC
NC| 38| –| NC| NC
NC| 39| –| NC| NC
NC| 40| –| NC| NC
NC| 41| –| NC| NC
GND| 42| –| Ground| Ground
GND| 43| –| Ground| Ground
NC| 44| –| NC| NC
GND| 45| –| Ground| Ground
The HUART interface can be used as a firmware rewrite or as a test command interface during certification tests. If necessary, connect to test pins, connectors, microprocessors, etc.
FCC
Note to users in the United States of America Caution:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Applicable FCC rules
Part 15 Subpart C
This device complies with below part 15 of FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID: SQK-7BTZ61
or Contains FCC ID: SQK-7BTZ61
The modular transmitter is only FCC authorized for the specific rule parts
(i.e., FCC transmitter rules) listed on the grant (Part 15 of the FCC rules),
and the host product manufacturer is responsible for compliance to any other
FCC rules that apply to the host not covered by the modular transmitter grant
of certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
Note to users in the United States of America and Canada Note to users
It is strictly forbidden to use antenna except designated.
This equipment must not be co-located or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC/ISED radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that is deemed to comply without
testing of specific absorption rate(SAR).
Following information must be indicated on the host device of this module.
Contains IC: 337L-7BTZ61
European Community Compliance Statement Note:
Hereby, Fujitsu component Limited, declares that this FWM7BTZ61 is in
compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
https://www.fcl.fujitsu.com/products/wireless-modules/information/red.html
- Model: FWM7BTZ61
- Manufacturer: Fujitsu Component Limited
- Address: Shinagawa Seaside Park Tower, 12-4, Higashi-shinagawa 4-chome,Shinagawa-ku, Tokyo, 140-8586, Japan
- Importer: FUJITSU COMPONENTS EUROPE B.V.
- Address: Diamantlaan 25, 2132 WV Hoofddorp, The Netherlands
United Kingdom Compliance Statement Note:
Hereby, Fujitsu Component Limited, declares that this FWM7BTZ61 is in
compliance with the relevant statutory requirements.
The full text of the declaration of conformity is available at the following
internet address: https://www.fcl.fujitsu.com/products/wireless-
modules/information/red.html
- Model: FWM7BTZ61
- Manufacturer: Fujitsu Component Limited
- Address: Shinagawa Seaside Park Tower, 12-4, Higashi-shinagawa 4-chome,Shinagawa-ku, Tokyo, 140-8586, Japan
- Importer: FUJITSU COMPONENTS EUROPE B.V.
- Address: Diamantlaan 25, 2132 WV Hoofddorp, The Netherlands
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>