NEOUSYS SMIL-1700GC Series Extreme Rugged Computer Installation Guide
- June 16, 2024
- NEOUSYS
Table of Contents
NEOUSYS SMIL-1700GC Series Extreme Rugged Computer
Warning
- Only qualified service personnel should install and service this product to avoid injury.
- Observe all ESD procedures during installation to avoid damaging the equipment.
Preparing tools
Unpack the equipment and make sure the following tools are available and delivered contents are correct before you begin the installation procedure.
User-provided tools
- Anti-static wrist wrap
Packing List
Item | Description | Quantity |
---|---|---|
01 | SEMIL 1700GC series system | 1 |
02 | Drivers & utilities disc | 1 |
Overview
No. | Item | Description |
---|---|---|
1 | DC input | 8V to 48V DC input (M12 S-coded) |
2 | PoE+ GbE ports | The M12 X-coded Power over Ethernet (PoE) ports provide |
both
data connection and electric power to devices (eg. IP camera).
SEMIL – 1724GC| 1x IEEE 802.3at GbE+ port via Intel® 1219
3x IEEE 802.3at GbE+ port via Intel® 1210
SEMIL- 1744GC
SEMIL – 1728GC| 1x IEEE 802.3at GbE+ port via Intel® 1219
7x IEEE 802.3at GbE+ port via Intel® 1210
SEMIL – 1748GC
3| USB 2.0 port| The USB 2.0 ports are backward-compatible with USB 1.1 / 1.0.
SEM.IL • 1724GC| 2x US82.0 (Mt2 A-coded)
SEMIL – 1744GC
SEMIL – 1728GC| 4 x US82.0 {M12 A-coded)
SEMIL- 1748GC
4| VGA port| VGA output supports resolution up to 1920×1200@60Hz
5| Audio port| The audio port is only available on SEMIL-1 728GC and
SEMIL-1748GC systems only.
6| COM ports| COM 1 & 2 are RS-2:32 ports via an M12 A-coded connector
7| Power button| Use this button to turn on or force shutdown the system.
DC-IN
Warning
Please make sure the voltage of DC power is correct before you connect it to
the system. Supplying a voltage over 48V will damage the system.
Signal| M12 panel s i de| M12 cable connector end| Wire
color
---|---|---|---
V +| 3| 3|
GND| 2| 2|
V+| 1| 1|
GND| PE| PE|
PoE+ Gigabit Ethernet Port
The number of ports for each SEMIL 7O0GC model variant is listed be ow:
Model No.\ PO E+ ports | Port descript i on |
---|---|
SEMIL-1724GC | 1x IEEE 802.3at GbE+ port via Intel® 1219 |
3x EEE 8O2.3at GbE port via Intel® 1210
SEMIL-1744GC
SEMIL-1728GC| 1X IEEE 802.3al GbE+ po via Intel® 1219
7x 1EEE 8O2.3at GbE+ port via Intel® 1210
SEMIL-1748GC
Connector Pin Definition
S i gnal| M12 pane l s i de| M12
cab l e connector end| W i re co lor
---|---|---|---
LAN PO| 1| 1| |
LANNO| 2| 2|
LAN P1| 3| 3| |
LANN1| 4| 4|
LAN P3| 5| 5| |
LAN P3| 6| 6|
LAN P2| 7| 7| |
LAN P2| 8| 8|
USB Port
SEMIL-1724GC and SEMIL1744GC have two USB ports while SEMIL1728GC and SEMIL-
1748GC have four USB ports. The USB2.0 ports are implemented via native xHCI
(eXtensible Host Controller Interface) controller and are backward compatible
with USB 1.1 and USB 1.0 devices.
Legacy USB is supported so you can use USB keyboard/mouse in DOS.
Signal | M12 pane1 side | M12 cable connector end | Wire color |
---|---|---|---|
D1+ | 1 | 1 | |
D1- | 2 | 2 | |
VCC_USB | 3 | 3 | |
GND | 4 | 4 | |
GND | 5 | 5 | |
VCC-USB | 6 | 6 | |
D2- | 7 | 7 | |
D2+ | 8 | 8 |
VGA Port
VGA connector is the most common video display connection. The VGA output
supports up to 1920×1200@60Hz resolution.
signal| M12 panel side| M12 cable connector end| Wire
color
---|---|---|---
Red| 1| 1|
GREEN| 9| 9|
BLUE| 7| 7|
GND| 6| 6|
GND| 8| 8|
GND| 10| 10|
GND| 12| 12|
GND| 13| 13|
GND| 14| 14| |
GND| 11| 11|
GND| 16| 16| |
GND| 15| 15| |
P5V VGA| 17| 17| |
VGA SDA| 5| 5| |
HSYNC CN| 3| 3| |
VSVNC CN| 2| 2| |
VGA SCL| 4| 4| |
Audio Port (SEMIL-1728GC/ 1748GC Only)
Pin Definition
-
Socket end
-
Cable side
Signal | M12 Socket end | M12 cable side |
---|---|---|
Left channel | 4 | 4 |
Right channel | 5 | 5 |
Microphone | 7 | 7 |
Ground | 8 | 8 |
COM1/ COM2
The system provides two COM ports via an M12 A-coded connector for communicating with external devices. These COM ports are 3-wire RS232 specifications and provide up to 115200 bps baud rate.
Pin Definition
-
Panel side
-
Cable connector end
Signal | M12 panel side | M12 cable connector end | Wire Color |
---|---|---|---|
TXD1 | 1 | 1 | |
RXD1 | 2 | 2 | |
NC | 3 | 3 |
x
PWR_IGN| 4| 4|
GNO| 5| 5|
NC| 6| 6|
x
RXD2| 7| 7|
TXD2| 8| 8|
Power Button
The power button is a non-latched switch for ATX mode on/off operation. To turn on the system, press the power button and the PWR LED should light-up green. To turn off the system, issuing a shutdown command in OS is preferred, or you can simply press the power button. To force shutdown when the system freezes, press and hold the power button for 5 seconds. Please note that there is a 5-second interval between on/off operations (i.e. once the system is turned off, there is a 5-second wait before you can power-on the system).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>