BLOSSOM V8018 Jena 30 Inch Vanity Light Gray Installation Guide
- June 3, 2024
- blossom
Table of Contents
BLOSSOM V8018 Jena 30 Inch Vanity Light Gray
Features
- Furniture-grade waterproof polyvinyl Chloride board, protected with several Coats of polyurethane.
- Night lights & drawer lights with touch switches on both side panels.
- Luxury look Calacatta White or Light Grey matte glass drawer fronts.
- Two fully adjustable drawers with
- Full extension soft-close hardware.
Package Dimension
- 24” 26-3/8” X 20-15/32” X 24-1/64”
- 30” 32-43/64” X 20-15/32” X 24-1/64”
- 36” 38-37/64” X 20- 15/32” X 24-1/64”
Colors / Finishes
- Box-Matte White
- Drawer Fronts – Calacatta White or Light
- Grey matte glasses.
Gross Weight
- 24” 48.5LBS
- 30” 52.91LBS
- 36” 59.52LBS
Sink Top Options
Specification & Installation Guide
Side View
Wall Preparation
The typical dimensions shown will result in vanity cabinet height of 32-3/4”
(831mm). Depending on the sinks selected, the total height will vary from
33-1/2” (850mm) 35-1/4” (895mm). If an alternate height is desired, adjust the
rough-in and backing material heights using the dimensions
provided.
STEP 1
Cabinet positioning and installation
- The suggested height of the vanity installation is 32-3/4” (831mm) – not including the basin.
- The height of Leveling Bracket Installation is 26-1/2” (671mm).
- Please reserve the power around 21-5/8(550mm) off ground.
STEP 2
Leveling bracket installation & Wiring
WARNING
Shut off the power before wiring the vanity.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical furnishing, basic precautions should always be followed,
including the following:
WARNING
To reduce the risk of burns, fire, electric shock or injury to persons, Use
this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer. Never drop or
insert any object into any opening. Do not use it for outdoors.
WARNING
Risk of electric shock. Connect this furnishing to a properly grounded circuit
only. See Grounding instructions.
GROUNDING INSTRUCTIONS
This product must be connected to a grounded metal, permanent wiring system,
or an equipment-grounding conductor must be run with the circuit conductors
and connected to the equipment-ground-ing terminal.
WARNING
An Electrical option cabinet must be wired to a 20 Amp GFI (Ground Fault
Interrupter) Protected circuit when used in bathrooms and all other locations
required by the National Electric Code.
CAUTION
Require 120 VAC 20 Amp GFI protected circuit. PLEASE SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
STEP 3
Hang the cabinet on the leveling bracket and adjust it horizontally Place the
vanity on leveling bracket, Leveling brackets are only to level the vanity.
They are not designed for permanent support. Vanity needs to be secured into
the wood backing material.
STEP 4
Fixed Cabinet Install Lag Bolt after determining the height, left & right
position then fix the Vanity.
STEP 5
Install sink top with Silicone
If you need to install a 48″ double basin
Please link the wiring together after combining both
vanities
Link the wiring of both vanities
Please link the wiring together after combining both vanities and follow up by
Step 2.
STEP 6. Finish
Blossom Kitchen & Bath Supply Corporation
(718)-366-0088 | sales@BlossomUS.com |
www.BlossomUS.com For clarification, please
contact us at (718)-366-0088 or sales@BlossomUS.com All
dimensions are approximate and subject to standard tolerance. Specifications
are subject to change without prior notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>