ubiolabs OPL103E Road Hazard Lights Owner’s Manual
- June 3, 2024
- ubiolabs
Table of Contents
Ubiolabs OPL103E Road Hazard Lights
Lights Technical Specifications
- Model: UTL1004 Burn
- Time (Hours): Cell Type: Lithium
- Ion Polymer 2,600mAh 10 High, 150 Low
- Input USB-C, 5V/1A
- Battery Indicators: 4 white LEDs, each indicating 25% capacity
- Brightness: 150 Lumens Max
- Dimensions (each): 3″ x 3.5″ x 1.25 inches
- Weight: 125g
Features
- Wh1te L1ght Button
- Red Light Button :
- Intermittent Flash
- Battery Status LED Indicator
- Magnets (x3)
- USB-C Input
- Folding Stand
Battery Status LED Indicator
- LEDs show the remaining battery level of 100%each light
- A single blinking light indicates 75%
- there is less than a 25% charge remaining. 50% 25%
Placing the Lights
Use the easy fold-out stands to set your lights on a level surface. Use the
magnets to attach to your vehicle or similar surface.
Note : Keep away from the flame.
Wall Charger Technical Specifications
- Model: CHG1087
- Input AC 110-240V, 50-60Hz
- Output 18W 9V/2A with Hardwired 6FT cable and 3.5mm (M) DC Coaxial Connector
- Dimensions: 57.5mm x 43.22mm x 26.15m (1.96″ X 1.7″ X 1.02″)
- Weight 80g (with cable)
Car Adapter Technical Specifications
- Model: CHG1176
- Power Input DC 9-24V, 2A Max.
- Cable Length: 6 ft (2m)
- Weight 62g
Charging Case Technical Specifications
- Model: CAS1022
- Input DC 9-24V/2A via 3.5mm canon connection
- Outputs: 3 x USB-C (M), 5V/1A
- Dimensions: 237mm X 130mm X 81mm
- Weight 260g
Features
- Mesh Storage Pouch
- USB-C Connectors
- DC Input
Charging Your Lights
Open the case to access the lights and charging ports. Align each light with
the port and gently press it into place. The white lights blink to indicate
the current battery capacity.
When the hazard lights are fully charged, the lights will remain on until the
USB-C cable is removed. Close the case, being sure to zip shut If using the
wall adaptor, connect the AC adaptor to the input at the back of the case,
then connect the wall adaptor to an outlet. If using the car adaptor, connect
the AC adaptor to the input at the back of the case,
then connect the car adaptor to an outlet in the vehicle. At Fabio Labs, we
always continue to improve our products’ features and functionality. We
reserve the right to change specifications at any time without notice.
ATTENTION PLEASE!
We know you are excited to get charged up with Fabio, but for optimal battery
performance please fully charge your power bank before use or storage.
Warranty
At Ubio Labs, we are dedicated to designing and manufacturing products with
superior performance and 100% customer satisfaction. All of our products come
with a 1 year limited warranty from the date of purchase
DO NOT RETURN TO THE STORE
Our customer service team is here to help. Model: OPL 103E
www.ubiolabs.com
support@ubiolabs.com
1-866-642-4428 (Monday – Friday 9 am –
4:30 pm PST) Ubio Labs, Inc. I 2821 Northup Way, Suite 250 Bellevue, WA 98004
Important Safety Instructions
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: this device may not cause harmful interference,
and this device must accept any interference received, including interference
that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
WARNING – When using this product, basic precautions should always be followed, including the following:
-
Read all the instructions before using the product.
-
To reduce the risk of injury, close supervision is necessary when the product is used near children.
-
Do not put fingers or hands into the product.
-
Do not expose light to rain or snow.
-
Use of a power supply or charger not recommended or sold by the power pack manufacturer may result in a risk of fire or injury to persons.
-
Do not use the light that is damaged or modified. Damaged or modified batteries may exhibit unpredictable
behavior resulting in fire, explosion or risk of injury. -
Do not disassemble the light. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
-
Do not expose light to fire or excessive temperature. Exposure to fire or temperature above 212°F may cause an explosion.
-
Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
-
Switch off the light when not in use.
-
o not use this light during driving. Use only as auxiliary equipment after your vehicle has stopped safely.
-
This product cannot replace a car safety triangle, it is not a waterproof product.
-
CAUTION
Risk of Fire and Burns. Do Not Open, Crush, Heat Above 45°C or Incinerate. Follow the Manufacturer’s Instructions.
Important Safety Instruction when using batteries
Rechargeable batteries are only to be charged under adult supervision.
Do not incinerate.
Battery Disposal
The hazard lights contain rechargeable batteries that cannot be replaced or
removed by the user. When disposing of the product all state and local rules
and regulations must be followed.