MONSTER Airmars XKT08 Bluetooth Wireless Headphones Instruction Manual
- June 3, 2024
- Monster
Table of Contents
Airmars XKT08 Bluetooth Wireless Headphones
Instruction Manual
Product Parameters
| Transmission distance | ≥ 10m |
|---|---|
| Driver diameter | Φ13mm |
| Driver impedance | 32Ω ± 15% |
| Sensitivity | 109 ± 3d8 |
| Frequency response | 204z-20kHz |
| Battery capacity(charging case) | 3.7 V 300mAh |
| Battery capacity (Headphone) | 3.7 V 33mAh |
| Charging time (charging case) | ≈ 1.5hours |
| Music playtime (headphone) | ≈ 5 hours |
| Music playtime with charging case | ≈ 24 hours |
Packing list
| Headphone2
---|---
| charging case1
| Instructions Manual1
| Type-C charging cable*1
Product Schematic Description
Charge the charging case
Connect the charging case to the
5V power adapter with Type-C charging cable.
Rated input: 5V ** 30mA(Headphone)
Rated input: 5V ** 300mA(charging case)
Tips: When the Ice blue Indicator lashes while dosing the cover, please
charge In erne.
Indicator guide
| Mode | Description | Voice prompt |
|---|---|---|
| Power On | Headphone ice blue indicator flash for 1 second | “Power on” |
| Power off | Headphone red indicator flash 3 times | “Power off” |
| Pairing | The earphone flashes red and blue alternately | “Pairing” |
| Connected | Headphone indicator off | “Conneced” |
| Disconnected | The earphone flashes red and blue alternately | “Disconnected” |
| Low Battery | — | “Low Battery” |
| Headphones placed in charging case | The headphone indicator light is always | |
| on, when fully charged it goes out | — | |
| Charging case low power | Ice blue indicator flashes | — |
| Charging case charged | Red Indicator flashes | — |
| Charging case fully charged | Red Indicator lights up | — |
Product operating instructions
-
Power on
Method 1: Take out the headphones from charging box, the headphones will turn on automatically.
Method 2: Long press MFB for 3 seconds -
Power off
Method 1: put the headphone/s into the charging case and dose the cover.
Method 2: after disconnected from the Bluetooth device for 3 minutes. -
Pairing
Method 1: take out the headphones from the charging case, the headphones will start pairing automatically .
Method 2: search and dick for “Monster Airmars XKT08″ on the Bluetooth list of the smart device, and when connection is successful, Connected” will be heard.
*Headphones will try reconnecting to the device with in 3 minutes when connection is lost.
Note:
- Fully charge the headphones and power off before an intended not-in -use period.
- Unplug the charging cable after charging.
Operation
Normal
| Voice assistant: Press the left MFB for 2 seconds
Volume +: Click right MFB
Volume -: Click left MFB
Music playback
| Pause/Play: Double click Left/Right MFB
Last song: Triple dick left MFB
Next song: Triple dick right MFB
Phone
| Answer: Double click the left/right
MFB Reject: Press left/right MFB for 2 seconds
Hang up: Double click the lefUright MFB
Game/music switching: device connected
| Press right MFB for 2 seconds to enter game mode
Press right MFB for 2 seconds to enter music mode
Restore factory setting
Either headphones is not connected to the bluetooth device when turned on,
click the MFB 5 times to dear the previous pairing information and turn off.
Precautions
- Headphones will turn on automatically (needless to press any button) pair and connect the device when the charging case is opened. After placing the headphones in the charging case, they will turn off and automatic charging will start when the cover is closed.
- Charging every 15 days will extend battery life when not in use often. Cleaning off dirt on the charging contacts by cotton swabs with alcohol will maintain a good contact for charging.
- Keep battery (battery pack) away from inflammables or excessive heat such as direct sunlight.
- Intermittent is normal during playback for wireless products due to environmental factors, device brand, users’ behavior, etc.
Warnings
- Do not use headphones at high volume for an extended period of time.
- Keep the headphones away from dust and water.
- Do not disassemble the headphones and accessories, otherwise warranty will be voided.
- Keep headphones away from any impact or vibration.
- Do not use any chemical solvents or cleaning agent on the headphones.
This table is compiled according to SJ/T 11364.
| Name of the Parts | Hazardous Substances |
|---|---|
| Pb | Hg |
| Housing | O |
| Loudspeakers | O |
| PCBA | X |
| Accessories | X |
O: Indicates that this hazardous substance contained in all of the
homogeneous materials for this part is below the limit requirement in G13/1″
26572.
X: Indicates that this hazardous subatance contained in at least one of
the homogeneous materials used for this part is above the limit requirement in
Gan- 26572.
Environment Friendly Use Period (EFUP)
This logo refers to the period (10 years) during which the hazardous
substances in electronic and electrical products will not leak or mutate so
that the use of these [substances] will not result in any severe environmental
pollution, any bodily injury or damage to any assets.
Warranty Service
Dear user, this warranty card is the proof of your future warranty application
with the seller to fill it out and keep it for future use!
User information
User name: ——————–
Email: ——————–
Contact number: ——————–
Postal code: ——————–
Mailing address: ——————–
Product information
Product name: ——————–
Product number: ——————–
Product barcode/Serial number/Batch number: ——————–
Vendor information
Name: ——————–
Address: ——————–
Contact number: ——————–
Postal code: ——————–
Sates date: ——————–
Invoice number: ——————–
Remark: ——————–
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the users authority to operate the equipment.
FCC ID: 2A8PV-QSMXKTO8
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>