R and G Racing RAD0343PRO Suzuki V Strom 800RE Radiator Guard PRO Instruction Manual

: September 21, 2024
: R AND G RACING

Table of Contents

R and G Racing RAD0343PRO Suzuki V Strom 800RE Radiator Guard PRO
Product Information
FAQ
GENERAL TORQUE SETTINGS
LEGEND
ASSEMBLY DIAGRAM
FITTING PICTURE
FITTING INSTRUCTIONS
CONSUMER NOTICE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

R and G Racing RAD0343PRO Suzuki V Strom 800RE Radiator Guard PRO

Product Information

Specifications

Model: RAD0343PRO
Description: Radiator Guard
Manufacturer: R&G Racing
Location: Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Contact: Tel: +44 (0)1420 89007 | Fax: +44 (0)1420 87301 |
Email: info@rg-racing.com

FAQ

Q: Can I discard the rubber washers included in the kit?

A: Yes, if rubber washers are used to hold components onto bolts, they can be thrown away as per the instructions.

Q: Where can I find digital copies of the fitting instructions?

A: Digital copies of the instructions are available for download at www.rg- racing.com.

THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.

SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.

PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.

PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS,
THESE RUBBER WASHERS CAN BE THROWN AWAY.

TOOLS REQUIRED

CABLE CUTTERS OR SCISSORS.

GENERAL TORQUE SETTINGS

M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
M12 BOLT = 40Nm

LEGEND

ITEM NO.	DESCRIPTION	QTY
ITEM 1	RAD0318PRO RADIATOR GUARD	1
ITEM 2	CT220 CABLE TES	4
ITEM 3	RB0015 RUBBER BUNGS	6

ASSEMBLY DIAGRAM

FITTING PICTURE

FITTING INSTRUCTIONS

To begin, press 4 of the rubber bungs (ITEM 3) provided into the holes as shown in the assembly diagram, in the correct orientation.
Offer the radiator guard into position and secure the radiator guard using two cable ties (ITEM 2) through the lower holes and through the corner of the radiator fins.
Secure the top of the radiator guard using two cable ties (ITEM 2) around the radiator mounts arrowed in the fitting picture.
Cut off remaining cable tie.

CONSUMER NOTICE

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.

R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.

NOTICE DE MONTAGE POUR RAD0343PRO GRILLE DE PROTECTION RADIATEUR

R &G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com