ZYXEL Rugged Switch User Guide
- June 7, 2024
- ZYXEL
Table of Contents
- ZYXEL Rugged Switch User Guide
- A. Overview
- B. Dimension Illustration
- C. DIN-Rail Mounting
- D. Wall Mounting
- Screw the wall-mount brackets with screws in the accessory kit.
- F. Alarm Relay and Ground
- G. Console Connection
- H. Connect & Login to Managed Switch
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ZYXEL Rugged Switch User Guide
A. Overview
The RGS200-12P Managed Rugged switch is designed for supporting environmental hardening application. Managed switches are easier to prioritize, partition, and organize user’s network, providing a more reliable and better quality services.
B. Dimension Illustration
C. DIN-Rail Mounting
Mounting step:
- Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
- Hook the unit over the DIN rail.
- Push the bottom of the unit towards the DIN Rail until it locks in place.
D. Wall Mounting
Screw the wall-mount brackets with screws in the accessory kit.
E. Connecting Power Terminal Block
The switch can be powered from two power supplies (input range 12V – 58V).
Insert the positive and negative wires into V+ and Vcontacts
on the terminal block respectively and tighten the wire-clamp screws to
prevent the wires from being loosened
The DC power should be connected to a well-fused power supply.
Input power should be within the range of 54~58VDC for PoE+ compliant, or
48-58VDC for PoE compliant.
EU Importer
Zyxel Communication A/S Generatorvej 8D, 2860 Søborg, Denmark.
http://www.zyxel.dk
F. Alarm Relay and Ground
The alarm relay output contacts are in the middle of the DC terminal block connector as shown in the figure below. The alarm relay out is “Normal Open”, and it will be closed when detected any predefined failure such as power failures or Ethernet link failures. The relay output with current carrying capacity of 0.5A @ 24 VDC
G. Console Connection
- DB9 connector connect to computer COM port
- Baud rate: 115200bps
- 8 data bits, 1 stop bit
- No Parity
- None flow control
H. Connect & Login to Managed Switch
- Connecting to the Ethernet port (RJ45 Ethernet port) of Managed Switch.
- Factory default IP: 192.168.1.1
- Login with default account and password. Username: admin Password: 1234
This equipment is intended to be used in a Restricted Access Location, with access limited to SERVICE PERSONAL and USERS authorized to be in that location.
US Importer
Zyxel Communications, Inc 1130 North Miller Street Anaheim, CA 92806-2001
http://www.us.zyxel.com
Copyright © 2016 Zyxel Communications Corp. All Rights Reserved
A. The RGS200-12P Managed Rugged switch is designed for supporting environmental hardening application. Managed switches are easier to prioritize, partition, and organize user’s network, providing a more reliable and better quality services.
C. Mounting step:
- Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit.
- Hook the unit over the DIN rail.
- Push the bottom of the unit towards the DIN Rail until it locks in place.
D. Screw the wall-mount brackets with screws in the accessory kit.
E. The switch can be powered from two power supplies (input range 12V
– 58V). Insert the positive and negative wires into V+ and V- contacts on the
terminal block respectively and tighten the wire-clamp screws to
prevent the wires from being loosened.
- The DC power should be connected to a well-fused power supply.
- Input power should be within the range of 54~58VDC for PoE+ compliant, or 48-58VDC for PoE compliant.
F. The alarm relay output contacts are in the middle of the DC terminal
block connector as shown in the figure below. The alarm relay out is “Normal
Open”, and it will be closed when detected any predefined failure such as
power failures or Ethernet link failures. The relay output with current
carrying capacity of 0.5A @ 24 VDC
G. DB9 connector connect to computer COM port. Baud rate: 115200bps. 8
data bits, 1 stop bit. No Parity. None flow control.
H. 1. Connecting to the Ethernet port (RJ45 Ethernet port) of Managed Switch.
2. Factory default IP: 192.168.1.1 3. Login with default account and password.
Username: admin / Password: 1234
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>