ZYXEL WX5512-T0 AX6000 Gigabit Wireless Extender Instruction Manual
- June 3, 2024
- ZYXEL
Table of Contents
ZYXEL WX5512-T0 AX6000 Gigabit Wireless Extender Instruction Manual
Step 1 Hardware Installation
Attach the bracket to the bottom of the WX5512-TO as shown. See the back side
if you want to mount the WX5512-TO on a wall after the initial setup.
Step 2 Connect via WiFi (See the back side to connect via cable.)
Place the WX5512-TO Near Your Modem/Router
Place your WX5512-TO next to your modem/router (within 2 meters) for initial
setup. You can move the WX5512-TO to a new location after the initial setup.
Power on
Use the included power odoptor to connect the WX5512-TO power socket to on appropriate Power outlet and wait until the power LED 0 stays on solid green. If the LED does not stay on solid green, un-plug the power adaptor and plug it bock in again.
CONNECT the WX5512-TO Your Modem/Router
Press the WPS button once, the WXSSI2-TO WPS LEO G blinks Within Two minutes. press the WPS button on your modem/router. Then the WiFi LED C, blinks slowly (1 sec on and 1 sec off) during setup If the VYX5512-TOWPS LED CD turns red, do the process again.
If BUNKING: Connect your wireless device to the Win nome (SSID)/possword on the WX5512-TO bock lobe!. _ink (lenty Onor Blinking – The WX5512-TO is _ED connected to the modem/router. WWI LED Onor Blinking – Your WK5512-TO Is ready for your wireless devices to connect.
Walt Two minutes. When the I ink quality and WiFi LED are on or blinking. you can go to the next step to connect your wireless device to the WiFi.
Connect Your Device to the WiFi
Check whether the link quality LED is SOLID ON or BLINKING.
If SOLID ON: Your WXS512-TO has synced the winome(SSID)/possword with your
Zyxel gateway. Connect your wireless doylcst tothyexisting WIFI nom. ($$1D).
The clohaultWiFi no me and password are on the Axel gateway back label.
Relocate the WXSS12-TO to an Optimal Location
Unplug your WX5512-TOond move it too new location about halfway between your
modem/router and the area with o poor WiFi signal. Plug in your WX5S12-TO. The
WX5S12-TO must be within range of your modem/router WiFi network. If the link
quality LED 00U is OFF or RED, move the WX5R12-TO closer to the modem/router
and try again until the link quality LED 000 lights green. Now you con use
WiFi and the Internet
**CONNECT VIA CABLE
**
Use the included power adaptor to connect the W)(5512 -TO power socket to an appropriate power outlet and wait until the power LED 0 stays on solid green. If the LED does not stay on solid green, un-plug the power adaptor and plug It back in again.
Connect the WX5512-TO to Your Modem/Router
Connect Your Device to the WiFi
Check whether the link quality LED is SOLID ON or BLINKING.
If SOLID ON: Your WM512-‘113 has synced the WiFi name (SSID)/password with
your Zyxel gateway. Connect your wireless device to the existing WiFi name
(SSID). The default WiFi name and password are on the Zyxel gateway bock
label. Now you can use WiFi and the Internet.
If BLINKING: Connect your wireless device to the WWI name(SSID)/password on
the WXS512-TO bock label. Now you can use WiFi and the internet.
WALL MOUNTING
Attach the bracket to the back of the WX5512-TO as shown. Place the WX5512-TO so the wall mount hole lines up with the screw.
Slide the WX5512-TO down Drill a hole in the wall. Insert the screw anchor in the hole and install the screw. gently to fix it into place.
**MPRO MESH APP
** IF YOU ARE USING A ZYXEL MPRO MESH GATEWAY YOU CAN USE THE MPRO MESH APP TO MANAGE THE ZYXEL MPRO MESH SYSTEM INCLUDING THE WX5512-TO.
POWER
Green On – The WXSS12-TO is ready. Blinking – The WX5512-TO is starting
up or under the MPro Mesh configuration process.
Red On – The WX5512-TO detects a system error.
Blinking (fast) – The WX5512-TO is upgrading firmware.
Blinking (slow) – The Easy Mesh process has failed.
Off Not receiving power.
Link Quality
With Wireless Connection
Green On – The WiFi connection to the MPro Mesh router is good.
Red On – The signal is too weak. With Wired Connection
Green On – The Ethernet cable is connected to the WX5512-TO LAN port.
WiFi
Green On – 2.4G and 5G wireless radios are ready.
Blinking – Sending and receiving data.
Slow Blinking – (1 sec on and 1 sec off.) The WX5512-TO is applying WiFi
settings. Off The 2.4G or SG wireless radio is not ready or has failed.
WPS
Amber Blinking – The WPS process in progress. Off No WPS activity.
SAFTY WARNING
THE SAFTY WARNING DISPLAY AFTER YOU LOG INTO THE WEB CONFIGURATOR.
FCC Radiation Exposure Statement
- This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment
- This transmitter must be at least 45 cm from the user and must not be co-located or operating in conjunction with any other antenna or transmitter.
- Operation of this device is restricted to Indoor use only. except for relevant user’s manual mention that this device can be instolled into the externol environment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>