Toolcraft Battery LED Spotlight IP64 User Manual

****

Operating Instructions
Battery LED Spotlight IP64
Item No. 2229245 (20 W)
Item No. 2229246 (10 W)

Intended use

The product is intended to be used as a work light. It has three light settings and a USB-A output for charging mobile devices.
It has an ingress protection rating of IP64 which means it is dust-tight and can resist water splashing from all directions.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product for purposes other than those described above, the product may be damaged. In addition, improper use can result in other hazards. Read the instructions carefully and store them in a safe place. Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and product names are trademarks of their respective owners. All rights reserved.

Delivery content

• Unit
• Charging cable
• Operating instructions

Up-to-date operating instructions

Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.

http://www.conrad.com/downloads

Explanation of symbols

The symbol with the exclamation mark in the triangle is used to indicate important information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on operation.
This device was constructed according to protection class III. Protection class III includes electrical devices with a low voltage power supply  (< 50 volts) using a safety transformer or batteries/rechargeable batteries/solar energy etc. Devices in protection class III have no connection for protective insulation – they must not be connected to the protective earth.

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.
a) General information

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.

• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture, flammable gases, steam, and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. The safe operation can no longer be guaranteed if the product:
  – is visibly damaged,
  – is no longer working properly,
  – has been stored for extended periods in poor ambient conditions or
  – has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts, or a fall even from a low height can damage the product.

• Consult an expert when in doubt about the operation, safety, or connection of the appliance.

• Maintenance, modifications, and repairs must only be completed by a technician or an authorized repair center.

• Make sure the specifications of any connected device conform to the product specifications listed in the technical data section.

• Do not short-circuit the USB input (4).

• If you have questions that remain unanswered by these operating instructions, contact our technical support service or other technical personnel.
  b) Connected devices

• Also, observe the safety and operating instructions of any other devices which are connected to the product.
  c) LED light

• Attention, LED light:
  – Do not look directly into the LED light!
  – Do not look into the beam directly or with optical instruments!

Operating elements

1. Bracket (foldout 180º)

2. Power button
   High → low → SOS (red) → OFF

3. Cover (in open position)

4. USB-A output

5. Micro USB charging input

6. Recharging LED (red)

7. Full charge LED (green)

8. Charging device LED (red)

Operation

Before connecting, make sure that the USB power source can deliver sufficient current, otherwise, you may damage the source. Do not use a  USB port of a computer, keyboard or USB hub without a power adapter as the current supplied by these ports is insufficient.
Looking into an LED light in the darkness can cause temporary blindness. This can be dangerous in high-risk environments.
To protect the IP64 rating, check that the cover (4) forms a good seal when closed.
a) Work light
• Press the power button (2) repeatedly to cycle between light modes: High → low → SOS (red) → OFF.
• The work light will turn off when the battery needs to be recharged. Recharge it by connecting one end of the included charging cable to the Micro USB charging input (5), and the other end to a suitable power supply.
b) Power bank
• Connect your mobile device to the USB-A output (4).
• Charging will begin automatically on connection, and the charging device indicator (8) will light red.

Care and cleaning

• Disconnect the product, turn the light off, and allow to cool down before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol, or other chemical solutions as they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fiber-free cloth.

Disposal

Electronic devices are recyclable waste and must not be disposed of in the household waste. At the end of its service life, dispose of the product in accordance with applicable regulatory guidelines. You thus fulfill your statutory obligations and contribute to the protection of the environment.

Technical data

Battery ………………………………………….. Li-ion 6000 mAh (3 x 2000)
Battery recharge …………………………….. 1 A charger: approx. 12 hrs; 2 A charger: approx. 6-7 hrs
Input voltage / current ……………………… 5 V/DC / 1 A (via micro USB)
Output voltage / current …………………… 5 V/DC / 1 A (via USB-A)
Colour temperature …………………………. 6500 K (low and high mode)
Brightness ……………………………………… Item 2229245 (20 W): max. 2500 lm (high mode)
Item 2229246 (10 W): max. 1200 lm (high mode)

Material …………………………………………. ABS, aluminium
Ingress protection …………………………… IP64
Bracket …………………………………………. 180º
Protection class ……………………………… III
Operating/Storage conditions …………… -20 to +50 ºC
Cable ……………………………………………. Micro USB to USB-A (30 cm)
Dimensions ……………………………………. 172 x 43.8 x 132 mm (W x H x D)
Weight ………………………………………….. 0.58 kg

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems requires prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing. Copyright 2020 by Conrad Electronic SE.
*2229245-46_v1_0320_02_dh_m_en

References

• Conrad Electronic » All parts of success
• Download center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>