abode Kitchen Tap Althia Monobloc Installation Guide
- June 7, 2024
- abode
Table of Contents
Althia Monobloc
5-year warranty
Terms and Conditions
In the unlikely event that you should experience any defect in the materials
or workmanship of your new Abode mixer within 5 years of purchase, the
purchaser’s sole remedy shall be the replacement (at the manufacturer’s
discretion) of all or any part of the product that is defective. All working
parts and valves are guaranteed for a period of 5 years from purchase.
Decorative surface finishes and O-rings are guaranteed for 1 year from the
date of purchase provided that our advice concerning care has been observed
and no scouring agents have been used. This is provided that the mixer or tap
has been used for normal domestic purposes and that the care, installation,
and maintenance instructions have been observed. The warranty extends to the
original purchaser only.
Marks, scuffs, and scratches caused by improper installation or accidental damage are not covered by this guarantee. Neither are shade variations or any damage or defect caused by incorrect installation or abuse of the fitting.
As we are continuously improving and developing our range of products, finishes & colours, in the event of a valid claim, we may not be able to provide an identical replacement for the defective product throughout the guarantee period. Where an identical product is no longer available, we will supply the nearest equivalent from our then current product range. In assessing your claim, we must be given the opportunity to inspect the product as installed prior to removal. Any product returns must be packaged as received and complete.
No other warranties, express or implied, are made, including merchantability or fitness for a particular purpose. Under no circumstances shall the manufacturer be liable for any loss or damage arising from the purchase, use or inability to use this product, or for any special, indirect, incidental or consequential damages. No liability is accepted for consequential damage to other household fixtures, fittings or furnishings arising from this claim, even if attached to the product. No installer, dealer, agent, or employee of Abode has the authority to modify the obligations or limitations of this warranty.
Care Instructions for your Kitchen Sink tap
To maintain the appearance of this product, ensure that it is regularly cleaned only using a clean, soft damp cloth. A solution of warm water and a mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly and wiped dry. Any other cleaning action will invalidate your warranty. If the mixer tap has a diffuser it should be unscrewed and cleaned periodically in warm water.
Abrasive cleaners, scouring cleaners and acidic cleaners must not be used
under any circumstances. Avoid contact with all solvents (including
chlorinated solvents, ketones or acetones as these may result in surface
deterioration or etching). Also avoid contact with any harsh household
chemicals such as oven cleaners, drain cleaners, rust removers, paint
strippers and toilet bowl cleaners, bar keepers friend or Brasso.
Please leave these instructions for your customer.
Parts and Contents
Key
| Description|
Qty
| 
---|---|---|---
A| Mixertap body| 1
B| Base plinth| 1
C| Upper seal| 1
D| Fixing stud| 1
E| Triangular stabilising bracket| 1
F| Lower gasket| 1
G| Fixing bracket| 1
H| Fixing nut| 1
I| Hot Flexi tail (with integral NRV)| 1
J| Cold Flexi tail (with integral NRV)| 1
Installation Instructions:
Preparation
Before installing the new mixer it is essential that you thoroughly flush
through the supply pipes in order to remove any remaining solder, swarf or
impurities from your system. Failure to carry out this simple procedure could
cause problems or damage to the workings of the mixertap.
We strongly recommend installing particle filters and isolation valves to both
the hot and cold feed pipes in an accessible position. This will help to
prevent premature failure of the valves and ease any future maintenance.
All parts should be removed from their packaging and inspected for any transport damage prior to installation.
Shut off your water heating system and ensure that your mains stopcock is closed. Open the lowest hot and cold taps in the house and allow the water to run until the cold-water storage tank and pipes are fully empty. Please note, the hot water storage cylinder (if applicable) will always remain full.
This mixer tap requires a 35mm∅ tap hole, if replacing an existing tap, remove
the tap & clean the end of the feed pipes using wire wool the tap hole area
should be free from dirt and sealant.
Loosely position the tap and tailpipes to check if any alteration to the
existing pipework is required, if this is the case do this now.
Installation
1. Screw studded rod (D) into the base of the tap (A).
2. Place the upper seal (C) into the base plinth (B) then place the base
plinth (B) onto the bottom of the tap (A).
3. Screw the hot & cold water tailpipes (I & J) into the base of the tap (A)
as shown.
4. Place the mixer tap (A) and base plinth (B) onto the sink/worktop, passing
the tailpipes (I & J) and studded rod (D) through the tap hole and base plinth
(B)
5. Pass the triangular stabilizer (E), lower gasket (F), and then the fixing
bracket (G) over the studded rod (D) and around the flexible tailpipes (I & J)
6. Fasten the fixing nut (H) securely onto the fixing stud (D) to fix the tap
(A) into its correct location.
7. Connect the hot and cold tailpipes (I & J) to the water mains using ½”
BSPx15mm compression fittings.
Note : Non-return valves will be pre-inserted into tailpipes (I & J).
After installation
Once you have visually checked the new fittings and connections, ensure that all taps are closed except the new mixer tap which should be left open. Turn on the water supply at the mains stop cock. As the system starts to refill, check carefully for leaks. Once you are fully satisfied that there are no leaks, turn on the water heating. Clean the tap to remove any marks created during installation as instructed then place the cloth bag that has been provided to protect the tap until it is ready for use.
Important Technical Data
Minimum operating pressure 0.3 bar
Maximum operating pressure 5.5 bar
Maximum hot water temperature 70°C
Recommended hot water temperature 46°C
Note : If these temperatures or pressures are exceeded, even for short
periods, damage can result. In these instances, a thermostatic mixing or
pressure reducing valve should be installed.
All Abode taps are either WRAS approved or manufactured in accordance with
recognized European standards. Please ensure that your Abode Kitchen mixer is
fitted in accordance with Local Water Byelaws.
These installation guidelines have been prepared for your direction and you
must exercise due care at all times. We do not accept responsibility for
problems that may occur through improper installation. Whilst assembling the
tap take care not to accidentally loosen any screwed assemblies.
Abode is a registered trademark of Abode.
Manufacturers Product Reference
©Abode
10/2016
Unit L, Zenith Park, Whaley Road, Barnsley,S75 1HT.
Tel: 01226 283434 Fax: 01226 282434
www.abodedesigns.co.uk
All errors and omissions excepted.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>