EcoDim Smart Dimmer Schakelaar 200W LED User Manual
- June 7, 2024
- EcoDim
Table of Contents
- EcoDim Smart Dimmer Schakelaar 200W LED User Manual
- Smart Dimmer Schal?elaar 200W LED Item No. Eco.Dim-07 Zigbee
- 1. Specifications
- Suitable brands of cover material:
- 2. Installation
- 3. Connection diagram
- 5. Connecting home automation/opp
- 6. Settings
- 2. Pairing mode
- 3. Remove: There are two methods to remove the device from the Zigbee
- 4. TouchUnk: Reset the dimmer if they are included in a Zigbee Network.
- 5. Find and Bind: Please make sure the device and remote already added
- Suitable for most home automation/ apps:
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EcoDim Smart Dimmer Schakelaar 200W LED User Manual
Smart Dimmer Schal?elaar 200W LED Item No. Eco.Dim-07 Zigbee
1. Specifications
Input voltage 220-240 Vac, 50Hz
Power (load) 0-200W LED
Suitable for Led-, halogen-, light bulbs
Type dimmer R,C Phase cut
Working temperature 35 ·c
Operation Push / turn button
Dimensions 70.6×70.6x33mm
Weight 49,98g
Suitable brands of cover material:
,J Berker by Hager
,J Busch-Jaeger
,/Gira
✓ JUNG
✓ Kopp
,J Merten by Schneider
✓ Niko
✓ PEHA
2. Installation
Step 1: Remove the knob and the cover plate.
Step 2: Always make sure that the electricity is switched off during
installation. Then connect the wires as indicated in the ‘Connection diagram’.
Step 3: Now install the dimmer in the mounting box. Use screws or tighten
the screws of the mounting clamps.
Step 4: Switch the electricity back on. Switch on the connected lights by
pressing the dimmer shaft. Now adjust the ‘MIN/MAX adjustment, as described
under ‘MIN/MAX installation’
Step 5 : Optionally you may connect the dimmer to your SMART home system
as indicated under the heading “Connecting home automation/ apps”
Step 6: Place back the cover plate and dimmer knob.
3. Connection diagram
4. MIN/MAX adjustment
For the SMART dimmer to work optimally, you can adjust the lights to the
dimmer with the MIN and MAX adjustment. As soon as you start turning MIN and
MAX
adjustment, the dimmer will automatically go to the minimum and maximum light
range. MIN adjustment: Switch on the lights with the push/ turn button. When
the lights are on, insert a screwdriver in MIN and turn to the left. When the
light becomes unsteady, turn slightly back to the right so that the light
remains steady. MAX adjustment: Switch on the lights with the push/ turn
button. When the lights are on, insert a screwdriver in MAX and turn to the
right. When the light becomes unsteady, turn slightly back to
the left so that the light remains steady.
5. Connecting home automation/opp
Step 1: Switch on the dimmer (lights are on). The dimmer is already in
“pairing mode”. You can also do this by pressing the reset button on the
dimmer twice.
Step 2: Make sure that the pairing mode of your controller is on during
the previous step. You will find this in the manual of your controller.
Step 3 : The dimmer will be visible in your app and the previously set
MIN/ MAX position will be stored there . Other manuals concerning the
connection of the EcoDim smart dimmer with various known controllers can be
found on this page: www.ecodim.nl/downloads-srnart-dimrner.
6. Settings
1.Factocy settings
Press the reset button for at least 5 seconds, the indicator will stay in red
for 1 Os. Please note that all configuration parameters will be reset after
the device is reset or remove from the. nflwllrk.
2. Pairing mode
a. Remove the device from previous Zigbee Network if it has already been added
to, otherwise pairing will fail.
b. Press reset button twice. The indicator will start blinking blue and stay
solid for 1 Os when pairing succeed, timeout 15mins.
3. Remove: There are two methods to remove the device from the Zigbee
Network.
Method 1. From your Zigbee hub interface, choose to delete or reset the device
as instructed.
Method 2. Press the reset button for 3 times, the indicator will start
blinking purple and stay solid for 1 Os when remove finished, timeout 3mins.
4. TouchUnk: Reset the dimmer if they are included in a Zigbee Network.
a. Press the reset button for 4 times, the indicator will start blinking green
and stay soild for 1 Os, timeout 3mins.
b. Bring the remote controller within l 0cm of the smart dimmer and set the
remote controller into Touchlink comminssioning. Please note: Touch I ink will
be effectived when both device not added to a Zig bee Network each device can
link with one remote
5. Find and Bind: Please make sure the device and remote already added
to the same Zigbee Network .
a. Press the reset button for 5 times, the indicator will start blinking
yellow and stay soild for 1 Os.
b. Set the remote controller into find and bind mode and enable it. Refer to
corresponding remote .
The installation of the dimmer on 230 V mains power must be carried out by a qualified specialist in compliance with local regulations. Make sure that the power supply is switched off during all work.
Suitable for most home automation/ apps:
,/ Google AssistanVGoogle Home
,J Amazon Alexa
✓ Philips Hue
✓ HOMEY
./Domoticz
./Trust
✓ WINK
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>