PERLESMITH TV Wall Mount Bracket Full Motion Single Articulating Arm Instruction Manual
- June 7, 2024
- Perlesmith
Table of Contents
PERLESMITH TV Wall Mount Bracket Full Motion Single Articulating Arm
WARNING!
WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ FOLLOWING WARNINGS BEFOREBEGINNING.
- If you do not understand the instructions or have any concerns or questions, please contact customer service at supportus@perlesmith.com
- Do not install or assemble if the parts or hardware is damaged or missing. Not all parts and hardware included will be used. If you require replacement parts, contact customer service at supportus@perlesmith.com
- This product may contain moving parts. Use with caution.
- DO NOT INSTALL INTO DRYWALL ALONE.
- Please check www.perlesmith.com for more products and company information.
Tools Needed (Not Included)
Supplied Hardware
Hardware （Wall /Product)
Lag Bolts M6X60
|
Washers Ø6mm
|
Level
|
CAUTION!
These anchors are for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.
---|---
TV Screws / Washers
Washers
Ø6mm
M4-5-6
|
Spacers
L10mm
|
Spacers L5mm
|
Philips Screws
M6 x 15mm
M6 x 30mm
|
Philips Screws
M8 x 15mm
M8 x 45mm
|
Philips Screws
M4 x 30mm
STEP 1
Measure the distance between the holes located at the back of your TV (these
measures may form the shape of a square, or a rectangle) and check that these
taken measures are within the VESA() range for this wall mount. () VESA:
International standard established by the TV manufacturers used to determine
if LCD / LED TVs are compatible with wall mounts.
Check TV screws
Hand thread screws into the threaded inserts on the back of your TV to
determine which screw diameter (M4, M6, or M8) to use.
When attaching brackets to the flat screen. Be careful not to over tighten
screws and be sure that screws do not bottom out in the mounting holes.
STEP 2
For Flat screen TV
| For Curved TV
---|---
STEP 3A For Wood Stud Installation
WARNING:
Avoid potential personal injury or property damage! All lag bolts [A1] MUST BE
firmly tightened to prevent unwanted movement of the wall plate.
WARNING:
- Drywall covering the wall must not exceed 5/8 in. (16 mm)
- Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm)
- Stud center must be verified
3A-1
Use a stud finder (not included) to locate wood stud Mark the edge and center locations
3A-2
3A-3
Drill 3 pilot holes using a Vs in.(3mm) diameter drill bit. Make sure the depth is not less than 2.36 in. (60mm).
3A-4
Mount the wall plate using 3 sets of M6 lag bolts A1 and washers A2 with a
socket wrench (not included).
STEP 3B For Concrete Wall Installation
WARNING
Avoid potential personal injury or property damage! All lag bolts [A1] MUST
BE firmly tightened to prevent unwanted movement of the wall plate.
WARNING:
- Mount the arm assembly/wall plate directly onto the concrete surface
- Minimum solid concrete thickness: 203 mm (8 in.)
- Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
3B-1
Position the wall plate at your desired height, level the wall plate and mark
the pilot hole locations.
3B-2
Drill 4 pilot holes using a 25/64 in. (10mm) diameter drill bit. Make sure the
depth is not less than 2.56 in.(65mm).
3B-3
Install wall plate using lag bolts A1, washers A2 and anchors A3. Tighten the
lag bolts until they are pulled firmly against the wall plate.
STEP 4 Hang the TV onto the wall plate
Step 5 Level Adjustment
If needed, the TV can be leveled +/-3 degrees
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>