Razor Smart Balancing Electric Scooter Owner’s Manual

OWNER’S MANUAL

Read and understand this entire manual before allowing the child to use this product! For assistance contact Razor.
DO NOT RETURN TO THE STORE.

NOTE: Manual illustrations are for demonstration purposes only. Illustrations may not reflect the exact appearance of the actual product. Specifications subject to change without notice.

Please have your product along with the 19 character product I.D. code with you before contacting Razor for warranty assistance and/or replacement parts.
Product I.D. Code: _____ – ____ – ____

INTRODUCTION

This manual will help you understand, set up and safely use the Razor ® Hovertrax ™ Xray™. It is important that you adhere to all safety warnings and cautions that appear throughout and that you use good judgment when riding, so keep reading!

A NEW TECHNOLOGY, WITH NEW CONCEPTS FOR CONTROL AND SAFETY

As is obvious the first time you see it, the Razor Hovertrax Xray is different from things you may have ridden before. No handlebars. No front or rear wheel. No brake. It is new and it moves, which means if you are interested in riding it you should be interested in learning how to do that properly – and if you are interested in minimizing the risk of falling off or being injured, you should be very interested in focusing on how to ride this new product as safely as possible. Helping you do that is the goal of this Manual and other warnings. THIS PRODUCT IS NEW, IT IS DIFFERENT, BUT IT MOVES AND YOU MUST UNDERSTAND AND FOLLOW THE INSTRUCTIONS IN ORDER TO MAXIMIZE YOUR FUN AND MINIMIZE RISKS OF INJURY PRESENTED BY RIDING THIS NEW MOVING PRODUCT.

THE MOVEMENT OF THE RAZOR HOVERTRAX XRAY IS CONTROLLED BY THE ANGLE OF THE FOOT PLATFORMS, WHICH IS DETERMINED BY PRESSURE APPLIED BY THE RIDER’S FEET ON THE PLATFORMS.
Different? Well, yes, the Hovertrax Xray is “different.” It is an electrically motorized, computerized, gyroscopically-balance assisted, independently articulated, dual-platform two-wheeled personal mobility system. If that sounds unlike any bicycle, scooter,  RipStik, roller skate, or water ski you have ever used, you’re on the right track.  However, the Razor Hovertrax Xray does not operate “magically”, and it does not ly, float, or disappear. Its movements are not controlled remotely, or by the rider’s brainwaves or earnest good ishes, and it has neither a steering wheel nor a brake, nor external stabilizers of any kind. Yet it can go, stop,  urn, and back up – and all of this is controlled solely by the rider’s feet moving at angles relative to the ground. IT IS CRUCIAL TO RECOGNIZE AND TO REMEMBER AT ALL TIMES.  The angle of your feet –  forward, level, or rearward – on each foot platform is how Hovertrax Xray receives, processes, and executes instructions from the rider. This will affect the operation of the Razor Hovertrax Xray far more than leaning or shifting body weight” alone.
WARNING: Read this manual – including both “Safety Warnings” (pages 2-3) and How to Operate” (pages 7-10) and learn to ride safely!

SAFETY WARNINGS

WARNING: Whenever you ride the Hovertrax Xray you risk serious injury or death from collisions, falls, or loss of control. To ride safely, YOU MUST READ AND FOLLOW THE INSTRUCTIONS AND WARNINGS IN THIS MANUAL.

WARNING: Riding any electric product can be a hazardous activity certain conditions may cause the equipment to fail without the fault of the manufacturer. Like other electric ride-on products, the Razor Hovertrax Xray can and is intended to move, and it is, therefore, possible to lose control, fall off and/or get into dangerous situations that no amount of care, instruction, or expertise can eliminate. If such things occur you can be seriously injured or die, even when using safety equipment and other precautions. RIDE AT YOUR OWN RISK AND USE COMMON SENSE.
WARNING: Failure to read and understand the “How to Operate” section of this manual (pages 7-10) increases the risk of injury due to falls or other incidents.
WARNING: NOT FOR RIDERS UNDER AGE 8 OR HEAVIER THAN 176 LB (80 KG). DO NOT EXCEED THE WEIGHT LIMIT OF 176 lb (80 kg) – including backpacks and other items that might be carried. Exceeding the weight limit could injure the rider and damage the Razor Hovertrax Xray. Rider weight alone also does not necessarily mean a person’s size is appropriate to fit or maintain control of the Razor Hovertrax Xray. Keep this product away from small children and remember that this product is intended for use only by persons who are, at a minimum, completely comfortable and competent while operating the product.

Razor recommends that children under the age of 8 not be permitted to use this product. This recommendation is based not just on age or weight or height – it reflects consideration of expected maturity and skills as well as physical size. The recommended rider age of 8 years or older is only an estimate and can be affected by the rider’s size, weight, or skills – not override 8 years old or older will be suited to the product. Certainly, any rider unable to fit comfortably on the Razor Hovertrax Xray should not attempt to ride it, but a parent’s decision to allow his or her child to ride this product should be based on the child’s maturity, skill, and ability to follow rules. Razor emphasizes that adults are strongly advised not to disregard Razor’s recommendations or permit younger children to ride the Razor Hovertrax Xray.

Because products, like the Razor Hovertrax Xray, can and do present potential hazards plainly associated with their use, it is well recognized THE NEED FOR EXERCISE OF PARENTAL RESPONSIBILITY IN SELECTING RIDING PRODUCTS APPROPRIATE TO THE AGE OF A RIDER, OR PARENTAL SUPERVISION IN SITUATIONS IN WHICH CHILDREN OF VARIOUS AGES MAY HAVE ACCESS TO THE SAME RIDING PRODUCTS, IS IMPORTANT. Not every product is appropriate for every age or size of rider, and recommendations are intended to reflect the nature of the hazard and the expected mental or physical ability, or both, of a rider to cope with the hazards.

Persons with any mental or physical conditions that may make them susceptible to injury, impair their physical dexterity or mental capabilities to recognize, understand, and follow safety instructions, and be able to
understand the hazards inherent in a product’s use, should not use or be permitted to use products inappropriate for their abilities. Persons with heart conditions, head, back, or neck ailments (or prior surgeries to these areas of the body), or pregnant women, should be cautioned not to operate this product.

CHECK AND MAINTAIN RAZOR HOVERTRAX XRAY
WARNING: Always inspect the Razor Hovertrax Xray prior to use. Properly inspecting and maintaining your product can reduce the risk of injury. Before use, check to confirm that any and all guards or covers are in place and in serviceable condition. Check that the parts are functioning properly, that the tires are not damaged or worn excessively. The Razor Hovertrax Xray should be maintained and repaired in accordance with the manufacturer’s specifications, using only the manufacturer’s authorized replacement parts, and should not be modified from the manufacturer’s original design and configuration. Replace worn or broken parts immediately.

Always check the battery charge before using the Razor Hovertrax Xray. Do not ride the Razor Hovertrax Xray when its battery is low, as indicated by a flashing red light and beeping. The Razor Hovertrax Xray may stop operating and cause you to fall. Use only the Razor Hovertrax Xray charger.

WARNING: Check local laws and regulations to see where and how you may use your Razor Hovertrax Xray legally. Follow all applicable laws for vehicles and pedestrians.

SAFETY GUIDELINES FOR CONTINUED USE: AN IMPORTANT MESSAGE TO ALL USERS

Periodically review this information and make sure that you understand all warnings, cautions, instructions and safety topics. Do not let others ride the Razor Hovertrax Xray until they have read this manual. Any type of wheeled activity can be hazardous. Wheels can, and are intended to move and it is, therefore, possible to get into dangerous situations and/or lose control and/ or fall off. In such situations, serious injury or death could occur.

Always be aware of the activity around you. Use the Razor Hovertrax Xray in areas free from fixed or moving hazards. Watch your surroundings for pedestrians, animals, and riders of other wheeled devices.
WARNING: Only use the Razor Hovertrax Xray indoors or on completely smooth surfaces. Avoid obstacles and slippery surfaces, which could result in a loss of balance or traction and cause a fall. See the section on Terrain for more guidelines.

WARNING: Do not lift the Razor Hovertrax Xray off the ground when the product is turned on. Do not turn on the Razor Hovertrax Xray in mid-air. This will cause the wheels to spin freely which could result in injury to yourself or damage to things around you.

Ride defensively. Watch out for potential obstacles that could catch your wheel(s) or force you to swerve suddenly or lose control. Be careful to avoid pedestrians, skaters, skateboards, scooters, bikes, children or animals who may enter your path, and respect the rights and property of others.

Never carry passengers or allow more than one person at a time to ride the electric product.

Never use headphones or a cell phone when riding. Never hitch a ride with another product.

Do not ride the Razor Hovertrax Xray in wet or icy weather and never immerse this electric product in water, as the electrical and drive components could get damaged by water or possibly create other unsafe conditions.

NOTICE: This manual contains many warnings and cautions concerning the consequences of failing to maintain, inspect or properly use your Razor Hovertrax Xray product. Because any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each time such
a possibility is mentioned.

Wet, slick, bumpy, uneven, or rough surfaces may increase risks. Do not ride this electric product in mud, ice, puddles, or water. Avoid excessive speeds that can be associated with downhill rides. Never use near steps or
swimming pools.

Do not ride at night or when visibility is limited.

Be careful and know your limitations. Risk of injury increases as the degree of riding difficulty increases. The rider assumes all risks associated with aggressive riding activities.
WARNING: Never operate any moving product, including the Razor Hovertrax Xray, while under the influence of drugs or alcohol.

PROPER RIDING ATTIRE
Always wear proper protective equipment, such as an approved safety helmet (with chin strap securely buckled). A helmet may be legally required by local law or regulation in your area. Elbow pads, kneepads, wrist guards, a long- sleeved shirt, long pants, and gloves are recommended. Always wear athletic shoes (lace-up shoes with rubber soles) and keep shoelaces tied and out of the way of the wheels, motor, and drive system. Never ride barefooted or in sandals.

USING THE CHARGER
The charger supplied with the electric product should be regularly examined for damage to the cord, plug, enclosure, and other parts. In the event of such damage, the product must not be charged until the charger has been repaired or replaced.
Use only with the recommended charger.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate chargers near flammable materials.
Unplug the charger and disconnect from the product when not in use.
Always disconnect from the charger prior to wiping down and cleaning your product with a damp cloth.

FAILURE TO USE COMMON SENSE AND HEED THE ABOVE WARNINGS INCREASES THE RISK OF SERIOUS INJURY. USE WITH APPROPRIATE CAUTION AND SERIOUS ATTENTION TO SAFE OPERATION.

PRE-RIDE CHECKLIST

Wheels
Practice riding only in wide-open areas clear from curbs, parking blocks, and other obstacles, including things you may fall on or into if you lose your balance. Impacting the wheels against any hard surface can damage the wheels. Wheels are not covered under your limited warranty.
Hardware/Lose Parts
Before every ride, check all parts, such as nuts, bolts, fasteners, etc., to ensure they are secure and assembled
correctly. There should not be any unusual rattles or sounds from loose parts or broken components. If the product is damaged, do not ride. Reference “Safety Warnings” on pages 2 and 3 of this manual.

Safety Gear
Always wear proper protective gear, such as an approved safety helmet. Elbow pads, kneepads, and wrist guards are recommended. Always wear athletic shoes (lace-up shoes with rubber soles) and keep shoelaces tied and out of the way of the wheels, motor, and drive system. NEVER RIDE BAREFOOTED OR IN SANDALS.

Laws and Regulations
Always check and obey any local laws or regulations.

Storage
Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials, store indoors when not in use.

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US, and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed at the back of this manual.

BEFORE YOU BEGIN

Remove contents from box. Remove the separators that protect the components from damage during shipping.
Inspect the contents of the box for scratches or dents that may have occurred during shipping. Because the Hovertrax Xray was assembled and packed at the factory, there should not be any problems, even if the box has a few scars or dents. Please keep this box in case you need to send the Hovertrax Xray back for service or repairs. If you use another box, Razor will not be responsible for any damage caused during shipping.

MAKE SURE THE POWER BUTTON IS TURNED “OFF” BEFORE CONDUCTING ANY MAINTENANCE PROCEDURES.

Estimated Set-Up Time
Allow up to 6 hours for the initial charge ( see page 6 for charging information ).
Charger
Note: Charger design may vary from one shown

WARNING:
DO NOT USE NON-RAZOR PARTS WITH YOUR PRODUCT.
The Hovertrax Xray has been built to certain Razor design specifications. The original equipment supplied at the time of sale was selected on the basis of its compatibility with the frame and all other parts. Certain aftermarket components may not be compatible and will void the warranty.

Product ID Locations:
(See locations to the left)

1. The frame (Underneath Product)
2. Charger
3. UPC Side of Box (Not Shown)

Box Contents:

• Hovertrax Xray
• Charger
• Owner’s Manual

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed at the back of this manual.

ASSEMBLY AND SET-UP

Calibration Confirmation
Note: Your Hovertrax Xray should have been calibrated at the factory.

1 Place Hovertrax Xray on a level surface.

2 Turn power ON. If the product remains level or adjusts to become level, calibration has been confirmed. No further steps are needed.
If the product begins to roll or does not move into a level orientation, see Calibrating Hovertrax Xray.

Calibrating Hovertrax Xray

1.Place Hovertrax Xray on a level surface.

2.Manually adjust the platforms so they are level to the ground.

3. While keeping the product level, turn the power ON and HOLD until the product beeps and lights flash (approximately 15-20 seconds).

4. Turn power back OFF

5. Calibration complete.
Note: Once the product has been calibrated, no matter what position (angle) the platforms are in when it is turned off, the platforms will automatically self-balance themselves back to the calibrated position when the product is turned on.

CHARGING THE BATTERY

Your Hovertrax Xray comes with a lithium-ion battery pack. Your Hovertrax Xray may not have a fully charged battery; therefore you must charge the battery prior to use. Be  sure to charge the battery in a clean, dry location away from direct sunlight, flames or sparks.

• Use only the Razor Hovertrax Xray charger.

• Initial charge time: 6 hours.

•  Recharge time: up to 4 hours, even if the light turns green. Recommended maximum charging time is 24 hours.

• Always charge the battery immediately after riding.

• Fully charge the battery before storing it for extended periods of time.

• Unplug the charger from the wall outlet when not in use.

• Failure to recharge the battery periodically may result in a battery that will not accept a charge.

• Make sure the Hovertrax Xray power button is turned OFF when the product is not in use. If the power button is left on for an extended period of time, the battery may reach a stage at which it will no longer hold a charge.

•  Run time: Up to 40 minutes of continuous ride time. Run time may vary depending on riding conditions,
  rider weight, climate, and/or proper maintenance.

• Constant stopping and starting may shorten ride time.

• Do not charge at or below 32º F (0º C).

• Do not allow the charger or battery pack to overheat. If they seem warm, allow them to cool down. Charge only at room temperature.

• Do not place the product or charger in the sun or warm environment. Keep at normal room temperature.

Charger

Note: Charger design may vary from one shown

1.  Plug the charger plug into a wall outlet. The light on the charger should be green.
   Note: If the green light (LED) does not turn on, try a different outlet.

2. Make sure the power button is in the OFF position. Plug the charger into the charger port on the Hovertrax Xray. The light on the charger should turn red during charging. The light will turn green again when charging is complete.

Model| Voltage (Nominal) Vdc| Capacity (Nominal) Ah| Charge Temperature Range| Operating Temperature Range
---|---|---|---|---
Hovertrax Xray| 25.2| 2.4| 0° to 40°C 32° to 104°F| -10° to 40°C 14° to 104°F

Battery Power Level Indicator

• Green + Orange + Red Indicator Lights – Battery is sufficiently charged.
• Red + Orange Indicator Lights – Charge product as soon as possible. If you continue to ride the product, the orange light will turn off. The red light will begin flashing and the product will begin to beep.
• Flashing Red Indicator Light and Rapid Beeping – Step off and charge immediately. The battery is out of power and the product will automatically shut off. Do not attempt to ride until the product has been recharged.

WARNING:
Use ONLY with the recommended charger. Batteries are only to be charged under adult supervision. The charger is not a toy. Always disconnect the charger before wiping down and/or cleaning the  Hovertrax Xray ith a  damp cloth. The charger supplied with the  Hovertrax Xray should be regularly examined for damage to the cord, plug, enclosure, and other parts. In the event of such damage, the Hovertrax Xray must not be charged until it has been repaired or replaced. Chargers have built-in overcharge protection to prevent batteries from being overcharged. Wall outlet – Green (stand by) Wall outlet and product – Red (charging) Wall outlet and product – Green (charged) Note: Continue charging product even if the light turns green prior to 4 hours.

WARNING: Failure to recharge the battery at least once a month may result in a battery that will no longer accept a charge.

WARNING: The Hovertrax X-ray will notify you when the battery charge is dangerously low by eeping. The orange battery indicator light will turn off and the red light will begin to flash. If these warnings occur, immediately slow down and safely step off. Turn the product off. Do not attempt to ride again until the battery is recharged.

HOW TO OPERATE

HOW IT WORKS
The Hovertrax Xray responds to the rider’s foot movements. Remember this. The Hovertrax Xray moves due to fore and aft foot platform tilt caused by the rider’s foot (or feet).

Movement, speed, and stopping are controlled by the degree to which the rider’s feet cause the foot platforms of the Hovertrax Xray to no longer be parallel to the ground.

When the product is “ ON ”, the gyroscopic mechanized balancing feature of the overtax X-ray tries to keep the foot platforms of the product parallel to the ground. In use, Hovertrax X-ray hen detects changes from “level” which are caused by fore and aft pressure on the foot platform(s) applied by the rider’s feet. Such changes are interpreted by the Hovertrax Xray as instructions to make the wheels move. Hovertrax Xray tries to re-level a forward tilt by accelerating and tries to level a rearward tilt by decelerating.

PERIODIC RECALIBRATION IS RECOMMENDED
The Hovertrax Xray self-balancing features are calibrated to function with a detected “resting position” that is
level. Over time and usage, recalibration may be needed to assure “level” status. If inaccurate calibration persists, this could affect the operation of the unit by sending instructions to the motor(s) to move that may differ from the intended motion.
To calibrate the product (see page 5 for additional information):

• Turn power OFF.
• Manually adjust the platforms so they are parallel to the ground.
• Turn power ON and HOLD until it beeps and lights flash (approximately 15-20 seconds).
• Turn the power back OFF.
• Calibration complete.
  Once the product has been calibrated, no matter what position (angle) the platforms are in when it is turned off, the platforms will automatically self- balance themselves back to the calibrated position when turned on.

MOVING AND CHANGING DIRECTION:
When a rider stands on the Hovertrax Xray with an evenly weighted foot that is “level” on either foot platform:

• Pressing toes on both feet downward moves Hovertrax Xray forward
• Pressing heels on both feet downward moves Hovertrax Xray backward
• Turns are done by putting more downward pressure on the front side of the foot platform on the outside of the turn.
• A rider can spin in place by pushing downward on the front edge of the one-foot platform while simultaneously pushing down on the rear edge of the other foot platform.

ACCELERATING AND STOPPING:

•  To go faster or to slow down, press the foot platforms at a greater angle for “more” and reduce the angles
  for “less”.

• When slowing or stopping, if you continue to apply force to the edges opposite the direction of travel, you may not only stop but continue on to reverse your direction.

How does this happen? The fundamental principle is that the Hovertrax Xray is designed to be “at rest” when the foot platforms are level – and the gyroscopic mechanized balancing feature detects the “levelness” of the product. This same feature detects foot movements that cause a foot platform to no longer be “level” and it interprets these changes as orders to move.

That’s it. That’s how it works. It does what your feet tell it to do, and the product “self-balance” itself in order to be ready to detect and implement the instructions provided by a rider’s feet.

Understanding this principle is important for obvious reasons. It also suggests some obvious warnings for riding the  Hovertrax Xray, such as:

• Do not jump up and down on it: If you remove a foot (or both feet), then land back on the Hovertrax Xray and cause the foot platform(s) to change position relative to “level” in any degree, the machine could and will react by moving immediately in response to an “instruction”, which can result in loss of rider stability, balance or control.
• Shifting Weight Alone is Not the Issue: Do not presume that shifting weight alone controls motion – or, for that matter, that not shifting weight equals “stability”. Shifting of rider weight may be associated with an increase or decrease of foot pressures on the foot platforms, but it is the action of the feet on the foot platforms which instructs Hovertrax Xray to move. Conversely, if you were to shift your weight without altering the placement or angle of your feet so that the foot platforms remain level, the Hovertrax X-ray does not receive any “signal” to interpret.

Note: Do not lift the Hovertrax Xray off the ground when it is turned on. Do not turn on the Hovertrax Xray in mid-air.

Riding Tip: Certainly the rider may “lean” on the Hovertrax Xray, but leaning only affects the foot platform’s position to the extent the rider’s feet change their position. If the rider’s ankles are held at a consistent 90° angle, leaning will result in tilting. Note that leaning can exaggerate shifting of weight, which may affect the ability of a rider to recover to a level posture – increasing the possibility of a loss of balance.

HOW TO CHANGE MODES

Turn the power button “ ON “.

Training mode (Default mode from factory)

TO CHANGE TO NORMAL MODE

Press the power button twice BEFORE all indicator lights come on.

Normal mode

Hovertrax Xray is ready to ride.

Note: Whatever mode the Hovertrax Xray was left in when turned off, will be the mode it begins in when turned back on.
Note: To go back to training mode, turn the power OFF, then press the power button ON. Press the power button twice BEFORE all indicator lights come on.

HOW TO GET ON

Once you have charged the battery (see page 6 for charging information):

1. Power On: Set the Hovertrax Xray on the ground and turn the power on. The battery/power mode indicator will show either one or two lights to indicate mode (see page 8 for instructions on switching modes). Do NOT proceed to step two (2) until all lights on the indicator light up.

2. First Foot: While standing behind the Hovertrax Xray, put one foot on a foot platform, closer to the wheel than to the center. Use that foot to activate the foot platform by bringing that foot platform to a balanced, level position.

3. Confirm Activation: Confirm the first foot platform is activated. Move your foot back and forth and feel
   the response from the product. Play with this single-foot platform until you are comfortable keeping the foot platform motion minimal.

4. Step Up: With the first foot platform stable and still, step up on the second foot platform with your second footDo this away from furniture and other large objects. Don’t use a fixed object to brace or lift yourself – Keep your weight evenly distributed between the two-foot platforms. If you are uncomfortable; step back off and repeat from step 2. Try to stand on the Hovertrax Xray without moving.
   HOW TO RIDE:

5. Stand in Place: Hovertrax Xray is unique among two-wheeled items in that the active stabilization it provides allows you to stand in place. A scooter or bicycle may balance more easily when it moves, but a Hovertrax Xray can balance even while stationary.

6. Move Forward: To move forward, press down gradually with your feet on the fronts of both foot platforms. Do not lunge forward or lean excessively, as you may lose your balance.

7. Slow Down: To slow down or stop, apply pressure to the rear edges of the foot platforms by pushing down with your heels. Leaning back somewhat may be useful but remember your feet are giving the instructions! If you continue pushing the rear edges with your heels, you will be able to travel backward.

8. Turn: To turn left, slightly push your right foot down on the front of the right foot platform; to turn right,
   push down on the front of the left foot platform. This idea is to make one wheel turn a little bit faster than
   the other wheel.

9.  Rotate in Place: To rotate in place, push down on the front of the one-foot platform while pushing down with equal force on the rear of the other foot platform.
   HOVERTRAX XRAY SPEED CONTROL

10. Not too fast: The max speed of this product is 9 mph (14.5 km/h), however, the recommended top operating speed is approximately 6 mph (10 km/h). Speed may be affected by rider weight, surface conditions, battery charge, etc. The Hovertrax Xray is capable of exceeding the normal operating speed for short periods, which is designed to permit the wheels to react and “re-balance” the product by helping level itself. Do not attempt to “force” the Hovertrax Xray into continuous operation at “re-balance” speeds, as control will be more difficult and falls more likely.
    HOW TO GET OFF:
    

11. Slow down and stop
    

12. Step to the back
    

13. Power down

NOTE: If Hovertrax Xray is left on for more than 5 minutes, it will automatically turn off and beep.

PRODUCT WARNING SIGNALS
The Hovertrax Xray has several built-in protection features, which include:

• Self-leveling function: If the product is not level when powered on it will slowly rotate until it is level.
  Always wait to mount until it has completely stopped self-leveling and all lights on the battery power mode indicator are lit.

• Training Mode: This product can be set to training mode to operate at a slower speed (see page 8 for
  instructions). Do not operate in normal mode until you are completely comfortable riding in training mode.

• Low or charging the battery: The battery/power mode indicator light (orange) will indicate insufficient charge for operation by flashing and the product will beep.

•  Excessive angle shutoff: At excessively steep foot platform angles, the product will stop powered operation.

Riding Tip: Before your very first ride, expect to spend up to ten minutes in this stage of learning how to stand comfortably on the Hovertrax Xray.

Self-balancing Function: If the product is not level when powered on it will slowly rotate until it is level. Always wait to mount until it has completely stopped self-leveling and all lights on the battery/power
mode indicator are lit.

Riding Tip: Your practice on Hovertrax Xray should be to keep the platform in place and get a feel for the motions that are generated from small changes in your fore/aft foot pressure.

Riding Tip: Hovertrax Xray is best-ridden at speeds similar to a brisk walk, not faster.
Note : All lights flashing notes a leveling error. Do not ride until flashing stops.

RIDING TIPS

• Learn to ride the Hovertrax Xray in a large, safe area free from all forms of interference.
• Keep your posture upright, but relaxed. Align your body over the Hovertrax Xray and use a wide stance with your feet close to the wheels.
• Be alert. Scan both far ahead and in front of you – your eyes are your best tool for safely avoiding obstacles and slippery surfaces.
• Hold your arms comfortably at your side.
• Start at a slow and comfortable pace. Never aggressively accelerate or lunge forward.
• Be careful and considerate of others.
• Always ride under control at a speed that is safe for you and those around you.
• Always be prepared to stop.
• Respect pedestrians by always yielding the right of way.
• Avoid startling pedestrians. When approaching from behind, announce yourself and slow down to walking speed when passing. Pass on the left whenever possible. When approaching a pedestrian from the front, stay to the right and slow down.

HOVERTRAX XRAY TIPS
Once you have charged the battery, follow these six easy steps:

•  Remember to check for the green battery indicator light before you get on. If it is not lit, the product is not on and you will fall.
• Do not stand on or near the center or rotating portion of the foot platform.
•  Remember to keep your body relaxed through your back and legs. Stand naturally.
• Practice controlled stopping.
•  If you stand with one foot on the foot platform with the product on, keep that foot level, or the Hovertrax Xray will move.
• Be aware of the width of the Hovertrax Xray and the path you are traveling. Make sure you will fit.

TERRAIN AND AVOIDING HAZARDS, SLIPS, AND TRIPS
The Hovertrax Xray is intended for indoors or uses on smooth, flat surfaces. However, to prevent loss of traction, you must always be careful when riding and learn to identify and avoid slippery and wet surfaces, loose materials, slopes, potholes, and other obstacles.
Stop and step off the Hovertrax Xray over unsafe surfaces or terrain.
The Hovertrax Xray wheels must be able to grip the ground for you to stay upright. Slips occur when the Hovertrax X-ray loses traction, potentially causing a loss of control and a fall. Abrupt maneuvers and riding over slippery surface bumps, and lose objects and materials may cause the Hovertrax Xray to lose traction.

• Keep alert.
•  Never jump on or off the Hovertrax Xray with both feet.
• Please don’t ride transversely on a hillside or turn on a slope. This may cause Hovertrax Xray’s balance sensors to be unable to orient themselves to a “level” state, impairing rider control.
• Avoid riding over any surface where the undercarriage may strike an object.
• Use caution when riding over any change in terrain.

REPAIR AND MAINTENANCE

WARNING: Risk of fire–no user-serviceable parts.
Battery Care and Disposal
Do not store in freezing or below-freezing temperatures. To properly maintain your battery and ensure maximum battery life, carefully read the “Charging the Battery” section on page 6 of this owner’s manual.

CONTAINS A LITHIUM-ION BATTERY PACK. BATTERIES MUST BE RECYCLED. UL 2271 COMPLIANT.

Disposal: Your Razor Hovertrax Xray uses a lithium-ion battery pack which must be recycled or disposed of in an environmentally safe manner. Do not dispose of a battery pack in a fire. The battery pack may explode. Do not dispose of a battery pack in your regular household trash. The incineration, landfilling or mixing of batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state-approved lithium-ion battery recycler.

Charger
The charger supplied with the electric scooter should be regularly examined for damage to the cord, plug, enclosure, and other parts. In the event of such damage, the product must not be charged until it has been repaired or replaced.

To reduce the risk of injury, use ONLY with the charger supplied with this product or a replacement specified
by Razor.

Wheels
Wheels and drive systems are subject to normal wear and tear. It is the responsibility of the user to periodically
inspect wheels for excess wear.

Replacement Parts
For the complete selection of replacement parts visit www.razor.com.

Repair Centers
For a list of authorized Razor repair centers:

• Check online at www.razor.com.
• Call 866-467-2967 for the center nearest you.

Recycling Lithium-ion Batteries: Lithium-ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you.

In the US and Canada only: For more information regarding the recycling of rechargeable batteries,
call toll free 1-800-822-8837, or visit http://www.call2recycle.org
Caution: Do not handle damaged lithium-ion batteries.

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US, and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed at the back of this manual.

NOTICE: INSURANCE YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT.

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this unit not expressly approved by Razor USA LLC, could void the user’s authority to operate the equipment.

WARRANTY

Razor Limited Warranty
The manufacturer warranties this product to be free of manufacturing defects for a period of 90 days from the date of purchase. This Limited Warranty does not cover normal wear and tear, tires, tubes or cables, or any damage, failure or loss caused by improper assembly, maintenance, storage or use of the Razor Hovertrax Xray.
This Limited Warranty will be void if the product is ever:

• used in a manner other than for recreation or transportation;
•  modified in any way;
•  rented.
• The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product.
  Razor does not offer an extended warranty. If you have purchased an extended warranty, must be honored by the store at which it was purchased.
  For your records, save your original sales receipt with this manual and write the serial number below.

CUSTOMER SERVICE CONTACT INFORMATION

Need Help? Visit our website for product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed below:

AMERICAS

Razor USA LLC
P.O. Box 3610
Cerritos, CA 90703
USA
+1 866 467 2967
Monday – Friday
8:00 AM – 5:00 PM Pacific Time
customersupport@razorusa.com

| UNITED KINGDOM AND IRELAND
Razor USA LLC (UK)
Unit 20
Hartnoll Business Centre
Post Hill, Tiverton
Devon EX16 4NG
UK
+44 (0) 120 267 2702
info@razoreu.com
---|---
EUROPE, MIDDLE EAST, AFRICA
Razor USA LLC (Europe)
Handelsweg 2
2742 RD Waddinxveen
Netherlands
+44 (0) 120 267 2702
info@razoreu.com| DISTRIBUTED IN AUSTRALIA BY:
Funtastic Limited
Suite 2.01, Level 2
315 Ferntree Gully Road
Mount Waverley Vic 3149,
Australia
+1 800 244 543
info@funtastic.com.au
ASIA
Razor USA LLC (Asia)
P.O. Box 3610
Cerritos, CA 90703
USA
+81 50 7579 6622
info@razor-asia.com| IMPORTED IN JAPAN BY B-PLUS ASIA CORP.
Razor USA LLCKurokawa 3-1, Asaoku,
Kawasaki, Kanagawa
215-0035 JAPAN
+81 (0) 44 328 9057 Tel
+81 (0) 44 328 9067 Fax
info@razor-asia.com

Need Help? Visit our website for replacement parts, product support, a list of authorized service centers in the US and customer service contact information at www.razor.com. Please have the product I.D. code (located on the white label of your product) available for better assistance. Additional Customer Service contact information is listed at the back of this manual.

US Patent No.: 8,738,278 Additional International Patents Pending
Printed in China for Razor USA LLC.
Copyright ©2003-2020 Razor USA, LLC. All rights reserved. Razor® and the Razor logo design is among the registered trademarks of Razor USA LLC in the United States and/or select foreign countries. Patents and Hovertrax™ trademark licensed from Inventist, Inc.

References

• Razor | Scooters and Ride-ons for the whole family
• Call2Recycle | Leading the Charge For Battery Recycling
• Razor | Scooters and Ride-ons for the whole family

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>