PERLESMITH Universal TV Stand Table Top TV Stand Installation Guide
- June 7, 2024
- Perlesmith
Table of Contents
PERLESMITH Universal TV Stand Table Top TV Stand
IMPORTANT SAFETY INFORMATION
- Check package contents against Supplied Parts and Hardware Lists to assure that all components were received undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact customer service at supportus@perlesmith.com
- Not all parts and hardware included will be used.
- Carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact customer service at supportus@perlesmith.com
- This product may contain moving parts. Use with caution.
- Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.
- DO NOT INSTALL INTO DRYWALL ALONE.
- Please check www.perlesmith.com for more products and company information.
Tools Needed (Not lncluded)
Supplied Parts
Supplied Hardware
Hardware for Attaching TV Bracket to TV
Hardware for Attaching Arm Assembly/Wall Plate to Wall
Step 1: Install the Extensions [03] to Arm Assembly/Wall Plate[01]
Step 2: Attach the Arm Assembly/Wall Plate [01] to Wall
- For wood stud installation, follow STEP 2A
- For concrete installation, follow STEP 2B
Step 2A: Wood Stud Option
WARNING:
- Avoid potential personal injury or property damage! DO NOT over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until the washers [A2] are pulled firmly against the wall plate [01].
- DONOT USE ANCHOR [A3] FOR THIS STEP!
- Ensure the arm assembly/wall plate[01] is securely fastened to the wall before continuing on to the next step.
- Any material covering the wall must not exceed 5/8 in. (16 mm).
- Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm).
- Stud center must be verified.
2A-1
Use a stud finder(not included) to locate wood studs. Mark the edge and center locations.
2A-2
Position the wall plate template[08] at your desired height and line up the holes with your stud center line. Level the template and mark the holes.
2A-3
Drill 4 pilot holes using a 5 mm diameter drill bit. Make sure the depth is not less than 60mm.
2A-4
Install the arm assembly/wall plate using lag bolts [A1] and washer [A2]. Tighten the lag bolts [A1] only until the washers [A2] are pulled firmly against the wall plate
Step 2B: Solid Concrete or Concrete Block Option
WARNING:
- Avoid potential personal injury or property damage! DO NOT over-tighten the lag bolts [A1]. Tighten the lag bolts [A1] only until the washers [A2] are pulled firmly against the wall plate.
- Ensure the arm assembly/wall plate[01] is securely fastened to the wall before continuing on to the next step.
- Any material covering the wall must not exceed 5/8 in. (16 mm).
- Mount the arm assembly/wall plate [01] directly onto the concrete surface.
- Minimum solid concrete thickness: 203 mm (8 in.).
- Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.).
2B-1
Position the wall plate template [08] at your desired height, level the template and mark the pilot hole locations.
2B-2
Drill 4 pilot holes using a 10mm diameter drill bit. Make sure the depth is not less than 65mm. Never drill into the mortar between blocks.
2B-3
Install the arm assembly/wall plate [01] using lag bolts [A1], washers [A2] and anchors [A3]. Be sure the anchors [A3] are seated flush with the concrete surface. Tighten the lag bolts [A1] only until the washers [A2] are pulled firmly against the wall plate. DO NOT over-tighten the lag bolts [A1].
Step 3: Add the Decorative Cap [04] to the Arm Assembly/Wall Plate[01]
Step 4: Check TV Hole Pattern and Select TV Screws
Step 5: Select Spacers (if needed)
Step 6: Secure the TV Brackets [02] to Your TV
Step 7: Hang the TV onto the Arm Assembly/Wall Plate [01]
Step 8: Level Adjustment
- Loosen the two screws [S] on the rear of arm plate [01] , using the hex key.
- Level your TV.
- Retighten screws [S] to secure in place.
Step 9: Tilt Adjustment
- Loosen the tilt lever [T] on both sides.
- Adjust the TV tilt position.
- Tighten tilt lever [T] to secure the TV in place at your desired tilt angle.
Step 10: Manage Cables
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>