saxby Lucca Photocell Mini LED Bulkhead Instruction Manual
- June 7, 2024
- saxby
Table of Contents
Instruction leaflet
Lucca Photocell Mini LED Bulkhead
77916
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This product is Class 2 (Double insulated) and must not be earthed.
Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Install in accordance with IEE Wiring regulations and current Building Regulations. To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted. If replacing an existing fitting, make a careful note of the connections. This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. This product is rated at IP65.
Specification
Voltage: 240V ~ 50Hz
Lamp: 17W
LED Module – 4200K
IP rating: 65
Layout
• Plan the desired layout of this fitting carefully, ensuring the cables will
reach the distance between the junction box and the light fitting.
• Avoid locating any cables in positions that would cause a hazard. Position
cables and junction boxes (not supplied) away from areas where they may be at
risk from being cut, trapped or damaged.
• The mains supply cable must have a minimum cross-sectional area of 1.0mm².
• Cables must be protected using suitable conduit or plastic trunking.
• The products can be wall or ceiling mounted.
Installation
Existing fittings must be completely removed before the installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
• Gently pull the casing away from the shade and set it aside.
• Remove the 4 fixing screws and detach the shade. Keep safe for refitting
later.
• Hold the product in place and mark the position of the holes. Ensure the
wall is capable of holding the weight of the product, or if fitting to a
ceiling, ensure there is a joist at the point of fixing to support the weight
of the product.
• Knock out the chosen fixing holes
• Fix into position. Take care to avoid damaging any concealed wiring and
pipes. The correct fixings should be used for brick, cavity walls or
plasterboard.
• Pierce a hole in the grommet, and pull the cable through.
• Wire as detailed below
Wiring
• This product is double insulated and must not be earthed. If there are any incoming earth cables, they must be terminated in the spare terminal of the connection block. Having correctly identified the wiring from your existing light fitting,connect to the quick fit connection block in the following way:
Check that…
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
Commissioning
• Ensure that the screws and cable entry points are sealed to maintain the IP
rating of the product.
• Refit the shade, ensuring that the seals are correctly located.
• Gently push the casing onto the shade until it clips in place.
• Replace fuse or circuit breaker and switch on. Your light is now ready for
use.
Fitting/replacing bulbs
• This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Photocell Sensor
• This product is fitted with a photocell. The specification is as follows:
Rated load: 500W~850VA
Operating Level: 10~20 Lux On, 30~60 Lux Off
Operating Temperature: -40° C – +70° C
• It is normal for the sensor to take several minutes to turn off when the product is first installed. To test “turn on” during daylight hours – cover the sensor with opaque material. The test will take approximately 2 minutes.
Recycling advice
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
Safety information
For your safety, always switch off the supply before cleaning.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>