RunCam ScopeCam 2 4K User Manual

ScopeCam 2 4k User Manual

Instruction Diagram

1. WiFi Button
2. Powering on /off SwItCh
3. LEDI Red Light (Recording Status) / Blue Light(WIR Status)
4. LED2 Red Ughtf Recording Status)/ Green Light (Charging Status)
5. Micro-SDCad Slot
6. Type-C
7. MICROPHONE

Charging:

Type-C only supports DC 5V power supply, please use a conventional phone charger or power bank. Greenlight will turn on during charging, while it will turn off when it is fully charged.lt takes about 2 hours to get fully charged.
Low Battey Reminder:
When the battery is lower than 896, the camera vibrates 4 times continuously, the 30s each vibration.
MicroSD Card Capacity up to 128GB; High-Speed SD card (Class 10/UHS-VUHS- IVUHS-III )is highly recommended
Note: The camera only supports FAT32 or exFAT format, SD cards over 64GE: must be formatted via the App.

Basic Camera Operation

Start Recording| Push-button up,

LED1, LED2(Red Light) have a slow flash at 1s intervals simultaneously

---|---
Stop Recording| Push-button down,

LED1 and LED2(Red Light) turn off simultaneously

Open WiFi| Operational: Long Pressing WiFi button 3s in recording status

Waiting for a connection: LED1 ( Blue light flashes slowly at ls interval), Connected: LED1 (Blue Light is on)

Operation2: Long Pressing WiFi button 3s in shutdown status

Waiting for a connection: LED1( Blue light flashes slowly at ls interval) Connected: LED1 (Blue Light is on)

Close WiFi| Long pressing WiFi button 3s,

LED1 (Blue light) off, the camera turns off simultaneously

Forced shutdown| Long pressing WiFi button 8s
Abnormal Status| No SD card or SD card abnormality, LED1,

LED2 have a quick flash simultaneously

Connection to the Computer

U Disk Mode:

Connecting to PC via TYPE-C to USB, the camera will enter into U disk mode automatically, recording indicator(red light) is on

WEBCAM/PCCAM/UVC Mode

Short pressing WiFi button to switch to WEBCAM/PCCAM/UVC mode in U disk mode, then Short pressing WiFi button can switch back and forth to U Disk or WEBCAM mode.

NOTICE: If the camera cannot be recognized after connecting to the computer, please confirm whether there is a microSD card in Scope cam 2. If the information in the SD card cannot be read normally, please replace the USB cable or retry the computer USB port.

App

1. Long press WiFi button 3s, LED1(blue light) flashes, WiFi is started and waiting for a connection.
2. Find the SSID connection of the Scope Cam 2 in the wireless network of the mobile phone and enter the password, after a successful connection, firmware update/WiFi indicator (blue light) is constantly on
3. Default SSID: SCO24K*****PW:1234567890

Android and iOS APP: Search ‘RunCam App’ on Google Play/App Store, or download on our website: https://runcarn.com/download/scopecam2-4k.

Technical Support Please

visit: https://supportsuncam.com/hc/en-us

Parameter

4K@30fps/2.7K@60fps/1080P@120fps/1080P@100fps/1080P@60fps/180P@50fps
Video format| MPQH764)
Memory Card| Mi‹:n› SD(Max 2S£x§)
File system| Fct32/cxFat
Battery| 14OOmAh
Battery life| Abo‹rt 160 iJninrftes (2.7K     60fps) / 210 ixin‹nes (T080P(‘‘60fps)
C1›arg ing time| About 120 icinrites
Wi-Fi| 2.4g
USB I r›terface| Tyg-C
W‹›rk C‹zrrerit| T 7SW ( Prrr¥ i : 2,7K/FCf[n & wi-fi ‹›ff)
Work Temp| -10°C – 4S°C
Housing Material| Aluminum alloy & PA
Vibration motor| Built-in
Waterproof| IP64
Mount| Picatinny
Net Weight| 40mm@150g| 25mm@145g| 3.6mm@135g
Dimension| 112mm32mm36mm| 93mm32mm36mm| 79mm32mm36m

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>