Runcam B08NPCKXG2 RC Hybrid 4K FPV and HD Recording Camera User Manual

June 7, 2024
RunCam

Runcam B08NPCKXG2 RC Hybrid 4K FPV and HD Recording Camera

Instruction Diagram

Lens Module Connection Diagram

Micro SD Card

Capacity up to 128GB; U3 recommended (2.7K50/1080P120 requires U3 or above; other solutions require U1 or above)

Please push the shield a little bit up with one hand like showed in above step 1 and then press the SD card(step 2) with another hand to let the card pop out.

Basic Camera Operation

Poweri n g On / Off Long press the Power/Shutter button
Standby Mode Camera St at us Light: Blue is On

Mode Switch i ng

| In Standby Mode, long press the Mode Switch button to cycle through the recording mode and the QR code setting mode.

Video Mode

| Camera Status Light: Blue LED blinks slowly, one second interval Press the Power/Shutter button to start/stop recording.
QR Code Setting| Camera Status Light: Green is on
Use RunCam App to access to RunCam Hybrid interface, set it and create the QR code. Under QR code setting mode, use camera to scan the QR code. Switch to standby mode automatically after scanning successfully.
The status light is Blue.
HD Recording Firmware Update| Camera Status Light: Green LED blinks slowly, one second interval
SD Card Issues| Camera Status Light: Blue LED blinks quickly, 0.5 second interval
Le n s Module Bad Connection| Camera Status Light: Green LED blinks quickly, 0.5 second interval

Transmitter Connection Diagram

Warning: Current Input ≥1A (Don’t powered by VTx)

FPV Flight Controller Setup

FPV camera supports Joystick Control and UART Control. The top left corner of the screen will shortly display the current control mode. The default is Joystick control mode. You can switch the mode via below way:

  1. Short the two camera control pins (TX and RX on board as shown in below picture)

  2. Then power on, camera will auto switch between the two modes. The mode can be saved after power off.

  3. After switching to the desired mode, please unplug the short-circuit cable.

UART Control works with Flight Controllers:
BetaFlight 3.3 or above / ButterFlight 3.4 or above / CleanFlight 2.2 or above

Joystick Control

FPV OSD Menu

  • JOYSTICK CTRL: Camera is under Joystick Control and the icon remains for 5 seconds.
  • CARD ERROR: Card error or no SD card
  • CARD FULL: SD card is full
  • 4K   30FPS: Current video resolution, remains for 10 seconds

Quick Setting (Long press the upper button to enter the menu)

  • Press the middle button to switch ON / OFF
  • CLR: Clear RUNCAM logo or pilot’s name
  • POS: Move to POS to adjust position
  • SHARP VIEW: Turn on, it will increase the image details, but also noise
  • WIDESCREEN: Switch image ratio between 16:9 and 4:3.
  • SYSTEM: Press the middle button to switch NTSC/PAL. It will work only after you exit the menu and reboot.
  • EXIT: Exit and saved.

UART Control

  1. Flight controller wiring (Take UART3 for example)


  2. Beta ight 3.3 or above setting
    Just need to choose “Camera (RunCam Protocol)” on UART 3 as shown in below screenshot.

  3. UART Control (Operate with your remote controller. Yellow icon to indicate bar operation direction. Black dot means centering control )

  • When connected, The buzzer on Flight Controller will beep for 3 times; When disconnected, The buzzer on Flight Controller will beep for 2 times only; If connected successfully, you can long press the up button to enter the OSD menu, right button to switch preset scenes, left button to calibrate voltage and down button to reset OSD.

FPV camera Firmware Updating

  • Tips: The firmware upgrade needs to switch to UART CTRL mode

    1. Connect the RX on the camera board to an unoccupied TX on your flight Controller and TX to RX as shown in below picture.

    2. Open Speedy Bee APP, find firmware updating on the homepage at the left side.

    3. Choose the right camera, wanted firmware version and flight controller version and then press the download button.

    4. Follow the APP guidance to finish the updating.

HD Flight Controller Set

Preparation
  • Firmware: BetaFlight Firmware (3.2.0),CleanFlight Firmware(2.1.0) , KISS Firmware (1.3-RC30) or INAV Firmware (1.7.3).
  • Any available UART interface on the Flight Controller
  1. Connect the RunCam Hybrid with the UART interface of the Flight Controller

  2. Make the Flight Controller recognize the RunCam Hybrid
    For example, we connect the RunCam Hybrid to the UART 5 interface on the Flight Controller: connect the Flight Controller to the computer, then open the configurator software of the Flight Controller. (Open up the configurator that matches the firmware you are running, Betaflight Configurator for Betaflight, Cleanflight Configurator for Cleanflight). In the Peripherals column of the line UART 5 (on the Ports tab), select Camera (RunCam Protocol) and click Save And Reboot.

  3. Instructions of the functions of the camera and assigning transmitter channels to them
    In the Flight Controller Configurator, navigate to the Modes tab. There are new CAMERA WI-FI, CAMERA POWER and CAMERA CHANGE modes
    ● CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to move to the next menu item.
    ● CAMERA CHANGE MODE: Switch between the recording mode and the QR code setting mode.
    Assign any available channel to the function you need, for example:
    ● Assign the AUX2 to the CAMERA POWER, range 1900-2100
    ● Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100

  4. Assign the channel to the switch of the controller
    Please choose your Model on the controller, then access to the MIXER interface and assign the channel to the switch of the controller. Take opentx 2.2.0 for example, assign the channels CH5, CH6 and CH7 to SA, SB and SD respectively

  5. Test
    Power the Flight Controller and the RunCam Hybrid
    ● Set the SA to the bottom, the camera starts/stops the video
    ● Set the SD to the bottom, the camera switches among the two modes: video and OSD setting mode

Technical Support

Please visit: https://support.runcam.com

Parameter

HD sensor SONY8MP
Analog sensor SONY 1.3MP
Field of View(FOV) HD Recording FOV 145°; (FPV FOV 150 ° @4:3)
Video Resolution 4K@30fps / 2.7K@60fps / 2.7K@50fps / 1080P@120fps I

1080P@1OOfpsI1080P@60fps/ 1080P@50fps
Video File Format| MP4
TV Mode| NTSC (720480)/PAL (720576) Switchable
Interface| HD supports UART remote control;
FPV (Analog) supports UART firmware update.
Max Micro SD Card Supported| Up to 128G.Samsung ‘s U3 card is recommended (2.7K60/1080P120 requires U3 or above; other solutions require U1 or above) Please make sure that the file format of the SD card is FAT32, otherwise, it will easily cause errors.
Mounting Holes Distance| 2020mm
PCB Size| 29
29mm
Lens Module Size| 19*25mm
Lens Specs| HD Lens: Ml0| FPV Lens: M8
Power Input| DC 5-20V (Non-direct power supply from 4s battery or above.
Powered directly with battery will generate surges and burn the camera.)
Working Current| 480mA@5V / 140mA @12V
Weight| 18g

www.runcam.com

Documents / Resources

| Runcam B08NPCKXG2 RC Hybrid 4K FPV and HD Recording Camera [pdf] User Manual
B08NPCKXG2, RC Hybrid, 4K FPV and HD Recording Camera, Recording Camera, Dual Recording Camera
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals