RunCam 6 4K HD FPV Action Camera With ND Filters User Manual

May 15, 2024
RunCam

Run Cam 6 4K HD FPV Action Camera With ND Filters

User Manual Runcam6

Diagram

Diagram

  1. Lens protection hood
  2. OLED Display
  3. Wi-Fi/Menu button
  4. Power/Shutter button
  5. Power light indicator
  6. Wi-Fi/Menu light indicator
  7. Type-C port
  8. HDMI port
  9. MicroSD card holder
  10. Battery holder

Power indicator light

Red: recording Green: charging
Wi-Fi/Menu indicator light
Blue: Wi-Fi/Firmware update Orange: menu setting

Camera Basic Operations

  • Power on/Power of
    Long press Power/Shutter button buzzer beeps 3 times with power light on and camera icon on OLED display, camera is turned on.
    Long press the Power/Shutter button buzzer beeps 5 times with power light and OLED display off, camera is turned off.
    Camera Basic Operations

  • Video mode
    After turning on the camera, short press the Power/ Shutter button buzzer beeps once, power light blinks red slowly, OLED display shows recording time, camera starts recording. When camera records, short press Power/Shutter button buzzer beeps twice, power light turns solid red, OLED display goes to ready mode, camera stops recording.

  • Wi-Fi mode
    At standby mode, short press Wi-Fi/Menu button   buzzer beeps once, Wi- Fi/Menu light blinks blue slowly, OLED display shows WiFi icon, the camera turns on Wi-Fi and waits for a connection.
    When camera is connected via Wi-Fi, Wi-Fi/Menu light  stays solid blue.
    At Wi-Fi mode, short press Wi-Fi/Menu button buzzer beeps once with Wi-Fi/Menu blue light and WiFi icon off, camera turns off Wi-Fi and stays standby.
    Wi-Fi mode

  • Menu mode
    At standby mode, long press Wi-Fi/Menu button to enter menu setting mode, buzzer beeps once, Wi-Fi/Menu light turns solid orange, OLED display shows menu setting. Long press Wi-Fi/Menu button  to quit OLED setting mode, buzzer beeps once with orange Wi-Fi/Menu light off, OLED display and camera go back to standby mode.

  • Low power alarm
    When the camera is low, the orange light flashes and the buzzer beeps each 3 seconds till camera powers of

  • Forced shutdown
    When the camera behaves abnormally and both buttons don’t give any responses, press both buttons simultaneously to shut down the camera.

  • Abnormal conditions
    Card error(no card, card full or low-speed card, etc):
    Red light blinks quickly Failed Wi-Fi connection: Wi-Fi/Menu light doesn’t blink or always stays solid blue
    Abnormal booting: Camera fails to detect the lens module, and blue light blinks quickly with OLED display on, camera shuts off in 5 seconds.

OLED Display

Display icons

Menu

Menu

Wi-Fi

Wi-Fi

Camera conditions

  • Firmware update
    Camera conditions

  • U-Disk mode
    U-Disk mode

  • Abnormal booting
    Abnormal booting

  • UVC mode
    UVC mode

Lens protection hood

Rotate the lens protection hood counterclockwise to remove, rotate it clockwise to install.

Lens protection hood

Battery holder

Push the battery door outward and flip, remove or install the battery.

Battery holder

Battery holder

Battery holder

Micro SD Card

MicroSD U3 card is recommended; Capacity of card is supported up to 512GB.

Notice:
Use carefully when handling memory cards. Avoid liquids, dust, and debris. As a precaution, please power off the camera before inserting or removing the card. Check manufacturer guidelines regarding use in acceptable temperature ranges. If camera cannot record, please format the used microSD card via Run Cam App or computer.

Computer Connection

Connect the camera to a computer via Type-C cable, the camera will be recognized as a U-Disk.

Notice:
If the camera cannot be recognized by the computer after connecting, please make sure that a microSD card is inserted well. If you cannot access the files inside the microSD card, please try another Type-C cable or port of PC.

Computer Connection

Firmware update

For camera’s best performance, please use the latest firmware.

Camera firmware update status: Light alternates quick-blinking blue Wi-Fi/Menu light and quick-blinking red Power light, and camera shuts off automatically when the update is finished. Firmware update method/download and Run Cam App:
https://www.runcam.com/download/Runcam6

Gyro Flow Support

  • Turn off stabilization
    Turn off stabilization

  • Use camera to record, and there will be Runcam6_0001.mp4 and Runcam6_0001.gcsv generated.

  • Download Gyro Flow from https://gyroflow.xyz/, install and run the software.
    Turn off stabilization

  • After stabilizing the recording video via Gyro Flow, export the video.

  • Please refer to an electronic document for more details.

Remote Control

Type-C Control cable instruction

Power wire

It supports external power input of DC5-18V.

Ground

Power ground wire / Remote control signal ground wire

Video

It can be soldered to VI pad of Flight Controller or Video In pad of Video Transmitter to transmit video signal to VTX.

PWM

It can be soldered to a spare M pad or LED pad of Flight Controller to achieve remote control for camera.

TX

It can be soldered to a R3 pad or other spare UART of Flight Controller to achieve remote control for camera.

RX

It can be soldered to a T3 pad or other spare UART of Flight Controller to achieve remote control for camera.

Remote Control

Remote Control via UART (Recommended)

Here we take Flight Controller Speedy Bee-F7 for an example

  • Solder the wires of Type C control cable to the pads on Speedy Bee F7 V3, with Power wire to 5V pad, GND wire to GND pad, Tx wire to R3 pad and Rx wire to T3 pad.
    Remote Control via UART \(Recommended\)

  • Use BetaFlight to configure, setting the UART3 of Speedy Bee F7 V3 as Run Cam device.
    Remote Control via UART \(Recommended\)

  • Configure at Modes
    Find the Modes tab at the BetaFlight, and there are three options for camera. Configure each for the functions of camera (select AUX by yourself), and the range is 1900-2100.For example:
    Configure at Modes

  • Assign the channels to the switch of the controller Please choose your Model on the
    controller, then access to the MIXER interface and assign the channel to the switches. Here we take Radio master TX12 as an example, assigning the channels CH5, CH6 and CH7 to SE, SB and SC position respectively.
    Configure at Modes

  • Test
    Power on Run Cam 6 and the Flight Controller

  • Set the SE to the bottom, the camera starts/stops recording

  • Set the SB to the bottom, the camera turns on/off WiFi.

  • Set the SC to the bottom, the camera switches among the two modes:
    video and OSD setting mode; At OSD mode, you can use SA position to select, and use SB to enter a sub-menu or confirm the setting.

  • PWM Remote Control
    Here we take Flight Controller Speedy Bee-F7 for an example

  • Solder the wires of Type C control cable to the pads on Speedy Bee F7 V3, with Power wire to 5V pad, GND wire to GND pad, PWM wire to M6 pad.
    PWM Remote Control

  • Configure M6 at CLI mode

  • Connect the flight controller to BetaFlight and enter the CLI interface

  • Type in resource to proceed, and type the command as below
    PWM Remote Control

  • Assign the channels to PWM
    PWM Remote Control

  • Assign the channels to a switch of the controller
    Please choose your Model on the controller, then access to the MIXER interface and assign the channel to a switch. Here takes Radio master TX12 as an example, assigning CH7 to SF position.

  • Test
    Set the SF to the bottom, toggle the switch once, camera starts/stops recording; toggles the switch three times, camera will switch to photo mode.

Run Cam App Connection

  1. After turning on the camera, short press the Wi-Fi/Menu button to turn on the Wi-Fi. The Wi-Fi light indicator will blink blue slowly, and camera waits for a connection on mobile device.
  2. Go to WLAN/Wi-Fi setting of a mobile phone and find Runcam6_XXXXXXX device to connect, type in the password 1234567890
  3. Turn to Run Cam App, select Run Cam 6 as the camera model to connect. Preview and configuration will be available after a successful connection.

Run Cam App Download

Run Cam App supports both Android and iOS system. Please search and download Run Cam App at Google Play/ AppStore.

Product Support

Please visit: https://support.runcam.com/hc/en-us

Specifications

Model Runcam6
Image Sensor SONY(12MP)
Resolutions 4K@30FPS/2.7K@60FPS/2.7K@30FPS/ 1440P@60FPS/1080P@120FPS/

1080P@60FPS/1080P@50FPS/1080P@30FPS
EIS| 6-DoF EIS
Lens| FOV D:155° H:135° V:77°
ISO| Auto
Shutter| Auto
Video File Format| MP4
WiFi| 2.4G
APP| Android ,IOS
Interface| Type-C/HDMI
Working Current| Max 500mA@ DC 5V
Run Time| 60Mins/4K30fps 110Mins/1080p60fps 135Mins/1080p30fps
Net weight| 49g(with battery)/35g(without battery)
Dimensions| 66.54020mm

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals