SATCO NUVO 60-7179 Sommerset 9 Light Chandelier with Clear Glass Brushed Nickel Finish Instruction Manual

June 5, 2024
SATCO NUVO

60-7179 Sommerset 9 Light Chandelier with Clear
Glass Brushed Nickel Finish
Instruction Manual

FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT  BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag-type fixture be installed on a ceiling that contains a radiant-type heating system. Read instructions carefully. If you are unclear as to how to proceed, consult a  qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this fixture.

FIXTURE ASSEMBLY

Carefully remove the fixture from the carton and check that all parts are included as shown in the figure. Be careful not to misplace any of the screws or parts, which are needed to install this fixture.
STEP 1: Place the nipple (M) over the tube (N) and tighten the nipple in coupling (O).
STEP 2: Thread rod (K) into the coupling (L). Carefully pass the wires through each rod during assembly. Repeat step 2 with rods (H), (I), and (J) until the desired hanging height is reached.
STEP 3: Thread the rod (H) onto swivel (G).

INSTALLATION

IMPORTANT: Do not attach the fixture directly to the outlet box.
STEP 1: Thread mounting screw (A) into the matching hole of the mounting bar (B).
STEP 2: Secure the mounting bar (B) to the outlet box with outlet box screws (C).
STEP 3: Hook the supporting cable (D) to the mounting bar (B).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to the ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied).
If the ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

GROUP A:
Connect to Black House Wire| GROUP B:
Connect to White House Wire
---|---
BLACK| WHITE
‘PARALLEL WIRE (round & smooth)| ‘PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER| WHITE OR GREY WITHOUT TRACER
BROWN. GOLD OR BLACK WITHOUT TRACER| BROWN. GOLD OR BLACK WITH TRACER

NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth (Seen best when viewed  from the wire end.)
STEP 3: Take your fixture wire(s) from group A and place it evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.

Line art shown may not exactly match the fixture enclosed. However, the installations do apply to this fixture.

STEP 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside the outlet box.
Raise canopy (E) allowing the mounting screw (A) to protrude through the hole in the canopy (A), and secure with finials (F).
STEP 2: Install lamps (not supplied). Do not exceed the maximum capacity recommended on the socket.
STEP 3: Place the glass (P) over the socket (R) and secure it with the screws (Q).
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts. Be sure to use exact wording from illustration when ordering parts.

© Copyright 2022 Satco Products, Inc. 5/22 v1.1

Documents / Resources

| SATCO NUVO 60-7179 Sommerset 9 Light Chandelier with Clear Glass Brushed Nickel Finish [pdf] Instruction Manual
60-7179, 60-7279, 60-7179 Sommerset 9 Light Chandelier with Clear Glass Brushed Nickel Finish, Sommerset 9 Light Chandelier with Clear Glass Brushed Nickel Finish
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SATCO NUVO User Manuals

Related Manuals