SATCO NUVO S28928 Hi Pro LED Wall Pack Lamps Instruction Manual
- June 5, 2024
- SATCO NUVO
Table of Contents
SATCO NUVO S28928 Hi Pro LED Wall Pack Lamps
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
-
Please read this manual carefully before use. Make sure the application is in accordance with the instructions before use.
-
Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit.
Check for enclosed wiring and components. -
To reduce the risk of electric shock and fire, this lamp must be installed, tested and maintained by professionals using special equipment.
-
Do not operate lamps on existing ballasts. These LED lamps require all the ballasts, capacitors, and
ignitors to be bypassed or removed. -
Suitable for dry and damp locations. Do not use where directly exposed to water.
-
Do not use with dimmers or attempt to dim.
-
Added weight of the device may cause instability of a free-standing portable luminaire.
-
This device is not intended for use with emergency exits.
-
Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
-
When using in portable table luminaires, ensure the distance from the bottom of the base to the top of the lampholder does not exceed three (3) times the base diameter.
-
Before installation make certain the AC power to the fixture is off.
-
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
-
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
-
I nstallers should not disconnect existing wires from lamp holder terminals to make new connections at lamp holder terminals. Instead installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder lead wires by employing applicable connectors.
-
For use in enclosed fixtures.
Item #| Watts| Volts (VAC)| Base| Dimensions
(Inches)| Min. Compartment| Operating Temperature
---|---|---|---|---|---|---
S28928| 20-10-5W|
100 – 277V
| E26| 5.43″ Length, ø3.62″|
N/A
|
Totally enclosed fixtures:
–22ºF to 113ºF (–30ºC to 45ºC)
Open fixtures:
–22ºF to 140ºF (–30ºC to 60ºC)
S28929| 40-30-20W| E26| 7.8″ Length, ø3.62″
S28930| 40-30-20W| EX39| 8.43″ Length, ø3.62″
S28980| 30-20-10W| E26| 7″ Length, ø3.62″
S28987| 60-40-20W| EX39| 10.59″ Length, ø3.62″| (L) 200mm/7.88″ x (W)
200mm/7.88″
INSTALLATION
Each lamp can be set to the desired color temperature and wattage during the
installation process.
NOTE: Before installation, select the Wattage and Color Temperature (CCT)
by sliding the switch, 3000K left, 4000K middle, 5000K right. See STEP 3.
-
STEP 1: Turn off the power before installation. Remove the old ballast, capacitor and ignitor (if existing). See Figure 1.
-
STEP 2: Make sure the Alternating Current Wires connect to the E39, EX39, and E26 socket directly. Reattach or replace ground lead if one is needed. See Figure 2.
-
STEP 3: Select wattage (on top of lamp).
-
STEP 4: Screw the LED lamp onto the corresponding socket. See Figure 4.
Securely fasten the earth fly lead cable to the main body structure. If cable is damaged, DO NOT USE. Replace with 1.0mm cable and insulate from heat. -
For installation in downward horizontal fixture, use support with double “prongs.” Cut to desired length after installation. See Figure 5.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>