Mine Site Technologies Pty UT33 Tag User Manual
- June 6, 2024
- Mine Site Technologies Pty
Table of Contents
Mine Site Technologies Pty UT33 Tag
Statement
Thank you for using this electronic product of our company. In order to let you experience the product swimmingly, detailed instruction is provided which you can find the introduction, usage and other information. Before using this product, please read the manual carefully, so that you can correctly use it. In case of any printing or translation error, we apologize for the inconvenience. As for the content change, we are sorry for no further notice.
General Information
The Mine Site Technologies model UT33 tag is a radio frequency identification module operating at 2.4GHz. The AL2236 IC of Airoha Technologu Corp and MSP430 microcontroller unit are working together, realizing the carrier arising,signal amplify,data modulation, demodulation and decoding. Radio- frequency mode in the reader and UT33 tag no contact between the bidirectional data transmission, in order to achieve target recognition and data exchange. And the tradition of code, magnetic and IC card, compared with non-contact, RF card reading speed, wear, not by environmental impact, long life, easy to use and has the characteristics of anti-collision function. Model UT33 tags are mainly used for container port, personnel to wear or other mining equipment, such as cap lamps, personnel tags, vehicle tags and equipment tags, etc.
Physical map
Model UT33 Tag physical map as follows.
Component function
- LED light: After press button and low voltage alarm.
- Button: Alarm.
Performance index
Mechanical Structure Index
Item| Name| Specific parameters
| Size| 46mm×25mm×15mm
| Weight| 10g
Electrical Performance Index
Item| Name| Specific parameters
| Power supply| Battery
| Rated voltage| DC 3.0V 4.2V
| ****
Working frequency
| Transmitter
Receive frequency:125KHz
| Communication
protocol
| ****
IEEE 802.11b
| Transmitter frequency| Adjust
| Low voltage alarm| V
Environment Index
Item| Name| Specific parameters
| Operating temperature.| -25 +60
| Anti-static grade| Air discharge 8000V
Accessories
- Tag.
- A set of use,s manual & warranty card
General attention
- Do not put tag on microwave oven or high-tension apparatus to avoid circuit damage and fire accident.
- Do not use under flammable and explosive gas in case of malfunction or lighting a fire.
- Do not put it on uneven or unstable surfaces to avoid falling off or breakdown.
- Tag You can replace if the battery capacity is insufficient. Use the battery appointed by the company. Other production may cause battery leakage, overheating, explosions and lighting a fire.
- Tag is worn by belt clips and lanyard Around the waist.
List of applicable FCC rules
FCC Part 15.247, FCC Part 2.1093
Specific operational use conditions
This product is a Limited Single Modular transmitter; Use only the supplied or an approved antenna.
Limited module procedures
Mine Site Technologies Pty Ltd will retain control over the final installation of the modular such that compliance of the end product is assured. In such cases, an operating condition on the limit modular approval for the module must be only approved for use when installed in devices produced by a specific manufacturer. If any hardware modify or RF control software modify will be made by host manufacturer. C2PC or new certificate should be apply to get approval, if those change and modification made by host manufacturer not expressly approved by the party responsible for compliance ,then it is illegal.
RF exposure considerations
This module certified that complies with RF exposure requirement under 0mm to body.
Information on test modes and additional testing requirements
Contact Mine Site Technologies Pty Ltd will provide stand-alone modular transmitter test mode. Additional testing and certification may be necessary when multiple modules are used in a host.
Additional testing, Part 15 Subpart B disclaimer
To ensure compliance with all non-transmitter functions the host manufacturer is responsible for ensuring compliance with the module(s) installed and fully operational. For example, if a host was previously authorized as an unintentional radiator under the Suppli Declaration of Conformity procedure without a transmitter certified module and a module is added, the host manufacturer is responsible for ensuring that the after the module is installed and operational the host continues to be compliant with the Part 15B unintentional radiator requirements. Since this may depend on the details of how the module is integrated with the host, Mine Site Technologies Pty Ltd shall provide guidance to the host manufacturer for compliance with the Part 15B requirements.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement:
Note 1: This device meets the government’s requirements for exposure to
radio waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation
of scientific studies. The standards include a substantial safety margin
designed to assure the safety of all persons regardless of age or health. The
SAR limit of USA (FCC) is 1.6 W/kg averaged. Device types: UT33 Tag (FCC ID:
N73-UT33) has also been tested against this SAR limit. SAR information on this
and other pad can be viewed on line at http://www.fcc.gov/oet/ea/fccid/.
Please use the device FCC ID number for search. This device was tested
simulation typical 10mm to body. To maintain compliance with FCC RF exposure
requirements, use accessories should maintain a separation distance between
the user’s bodies mentioned above, the use of belt clips, holsters and similar
accessories should not contair metallic components in its assembly. the use of
accessories that do not satisfy these requirements may not comply with FCC RF
exposure requirements, and should be avoided. Body-worn accessories that do
not meet these requirements may not comply with RF exposure requirements and
should be avoided. Use only the supplied or an approved antenna.
Note 2: Any modifications made to the module will void the Grant of Certification, this module is limited to OEM installation only and must not be sold to end-users, end-user has no manual instructions to remove or install the device, only software or operating procedure shall be placed in the end- user operating manual of final products.
Note 3: Additional testing and certification may be necessary when multiple modules are used.
Note 4: The module may be operated only with the antenna with which it is authorized. Any antenna that is of the same type and of equal or less directional gain as an antenna that is authorized with the intentional radiator may be marketed with, and used with, that intentional radiator.
Note 5: For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and economic development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This module is limited to OEM installation only and must not be sold to end-
users, end-user has no manual instructions to remove or install the device,
only software or operating procedure shall be placed in the end-user operating
manual of final products. Additional testing and certification may be
necessary when multiple modules are used.
Any changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate this equipment.
The final end product must be labeled in a visible area with the following ”
Contains IC: 7449B-UT33 “.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>