ULINE H-1225,H-3638,H-5533 Double Tier Locker Three Wide Instruction Manual
- June 7, 2024
- ULINE
Table of Contents
H-1225, H-3638 H-5533 |
uline.com
DOUBLE TIER LOCKER THREE WIDE
TOOL NEEDED
11/32″ Nut Driver (Included)
CAUTION! Some parts may have sharp edges. Care must be taken when handling various pieces to avoid injury. For your safety, wear work gloves when assembling.
PARTS
PRIMARY ASSEMBLY NO ASSEMBLY REQUIRED
# DESCRIPTION QTY.
1 Back 3
2 Left Side 2
3 Rear Leg 4
4 Top/Bottom 9
5 Coat Hook 18
6 Right Side 2
7 Locker Door 6
8 Door Frame Assembly 3
9 Number Plate 6
10 Push Plug 12
11 Latch and Spring 12
12 Bumper 12
13 Dart Clip 12
14 Locking Channel 6
15 Lock Receiver 6
16 Reinforcement Tab 6
17 Recessed Handle 6
18 Logo Plate 6
ASSEMBLY INSTRUCTIONS
ASSEMBLING MAIN PANELS
NOTE: Do not tighten bolts until unit is completely assembled.
-
Locate and separate the left and right-hand sides (2 & 6). Identify the top of each panel. The top of each panel has three holes instead of one.
-
Place back (1) on a protected flat surface so that the flanges face upward.
-
Bolt left side (2) to the back (1) so that side flange fits around back (use 7 bolts and nuts – nuts to the inside). Do not use bottom two holes; these will be used for attaching legs in step 7. (See Figure 1)
-
Next bolt top (4), bottom (4) and intermediate top (4) to back and left side panel (use 4 bolts and nuts each). Bolt an intermediate side and back panel to the flange on the back of the first locker in seven places. (See Figure 2)
-
Next attach a top, bottom and intermediate top to the first intermediate side and back. These will share bolts with the parts on either side of them as shown in detail view. (See Figure 2)
-
Next attach the remaining intermediate side and back panel to the flange on the back of the second locker. Then attach remaining top, bottom and intermediate top to the intermediate side. (See Figure 2)
-
Attach coat hooks (5) to each locker’s left side and back panel:
• Side - 2nd, 3rd & 9th, 10th holes from top.
• Back - 2nd, 3rd & 11th, 12th holes from top. -
Bolt right side (6) to the back so that side flange fits around back. (See Figure 3)
-
Insert legs (3) into the corner between the bottom and the side. Bolt the leg to the side using two bolts and nuts per leg. (See Figure 4)
-
Place door and frame assembly (7 & 8) over the locker body. Make certain the body sides are inside the frame and not between the frames. Attach top to frame header and bottom to frame sill (one bolt each). Finish by attaching the door and frame assembly to the sides of the locker body (bolts will be shared with the door and frame on either side of them). (See Figure 5) If joining a 3-wide unit beside another unit see JOINING UNITS TOGETHER below.
-
Stand unit upright and place in desired location. If joining units together, remove temporary bolts in frames and bolt adjacent units together through frames. Check and tighten all permanent bolts.
NOTE: If the temporary bolts are not removed before the frames are joined side by side, the frames will have a 1/8″ gap between them.
JOINING UNITS TOGETHER
1. If joining a 3-wide unit beside another unit, temporarily install a bolt and nut into the third and sixth holes down from the top of the outer frame(s) that will be joined to the adjacent locker frame(s). (See Figure 6) The center locker frame can be bolted complete.
SECURING UNITS
1. Anchor units to wall or floor. Units are not intended to stand free and may topple if not secured. (Units standing back to back should be bolted together.)
CAUTION! Care must be taken to assure that lockers are set plumb and true
before anchoring.
2. If units are not pre-numbered, an optional number plate (11) may be
attached with two #6 x 5/16 drive screws or push plugs (12).
1-800-295-5510
0821 IH-1225
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>