solaredge ENET-HBNP-01 Energy Net Kit Installation Guide
- June 6, 2024
- solaredge
Table of Contents
ENET-HBNP-01 Energy Net Kit
Installation Guide
The installation of the SolarEdge Energy Net Plug-in must be performed by a
qualified installer only.
Make sure to follow all safety and handling instructions specified in the
inverter installation guide.
Install the Antenna
To avoid electric shock, refer to safety instructions in the inverter installation guide before removing the inverter cover.
-
Turn off the inverter ON/OFF/P switch and DC safety switch (if applicable).
-
Turn off AC to the inverter on the main service panel.
-
Wait five minutes.
-
Open the inverter cover and Connection Unit cover (if applicable).
-
Clip the antenna (supplied) to a heatsink fin.
-
Pass the antenna cable through a communication gland.
Install and Connect the Plug-in
-
Connect the Energy Net plug-in to the dedicated socket on the communication board.
-
Connect the antenna to the Energy Net plug-in.
-
Tie the antenna cable to the communication board bracket with a plastic tie (supplied).
-
Mount the inverter cover and Connection Unit cover (if applicable). Tighten the screws to 8.4N⋅m/74lb-in.
Verify Connection
-
Turn on AC to the inverter on the main service panel.
-
Turn on the inverter ON/OFF/P switch and DC safety switch (if applicable).
-
Run NetApp
-
Scan the QR code on the inverter.
-
Verify connection.
Datasheet
Scan the QR code:
Or follow the link:
https://www.solaredge.com/sites/default/files/se-energy-net-plug-in-
datasheet.pdf
Regulatory Statements
Professional Installation Instructions
Installation Personnel
This product is designed for a specific application and needs to be installed
by qualified personnel. The user should not attempt to install the product or
change any of the product settings.
External Antenna
Use only the antennas, which have been approved by the applicant. Unapproved
antenna(s) may produce unwanted spurious or excessive RF transmitting power,
which may lead to violation of FCC/IC limits and is prohibited.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body. This module is
intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01
guidance, the following conditions must be strictly followed when using this
certified module:
- This module has been tested for compliance with FCC Part 15.
- The module is tested for standalone mobile RF exposure use conditions.
Any other usage conditions such as co-location with another transmitter (s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification.
RF Exposure Considerations
This equipment complies with the FCC mobile radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator & your body. If
the module is installed in a portable host, a separate SAR evaluation is
required to confirm compliance with relevant FCC portable RF exposure rules.
Antennas
The following antennas have been certified for use with this module; antennas
of the same type with equal or lower gain may also be used with this module.
The antenna must be installed such that 20 cm can be maintained between the
antenna and users.
Approved antenna(s) list:
Manufactures| MSS| Antenna Type| Max Gain (dBI)|
Impedance (Ω)
---|---|---|---|---
RALTRON| RST-TUA3-TUB7-320020-17M-A-002| Dipole| 3d8i| 50otirn
RALTRON| RST-TUA3-TUB7-19550200-17M-A-001| Dipole| 3d8i| 50otirn
SolarEdge| AS4034-1| Dipole| Od8i| 50otirn
SolarEdge| AS4035-1| Coil| Od8i| 50otirn
Label and Compliance Information
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: 2AGPT-ENET”. The grantee’s FCC ID can be used only when all
FCC compliance requirements are met.
Information on Test Modes and Additional Testing Requirements
This transmitter is tested in a standalone mobile RF exposure condition and
any co-located or simultaneous transmission with another transmitter (s) or
portable use will require a separate class II permissive change re-evaluation
or new certification.
Additional Testing, Part 15 Subpart B Disclaimer
This transmitter module is tested as a subsystem and its certification does
not cover the FCC Part 15, Subpart B (unintentional radiator) rule requirement
applicable to the final host. The final host will still need to be reassessed
for compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, no further transmitter test will be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and the
FCC ID can not be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including
the transmitter) and obtaining a separate FCC authorization.
Manual Information to the End-User
The OEM integrator has to be aware not to provide information to the end-user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end-user manual shall include all required regulatory information/warning
as shown in this manual.
OEM/Host Manufacturer Responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the
Host and Module. The final product must be reassessed against all the
essential requirements of the FCC rule such as FCC Part 15 Subpart B before it
can be placed on the US market. This includes reassessing the transmitter
module for compliance with the Radio and EMF essential requirements of the FCC
rules. This module must not be incorporated into any other device or system
without retesting for compliance as multi-radio and combined equipment.
Industry Canada Statement
This device complies with ISED’s license-exempt RSS. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that
may cause undesired operation.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions (for module device use):
- The antenna must be installed and operated with a minimum distance of 20cm between the antenna and users, and
- The transmitter module may not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, no further transmitter test will be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada
authorization is no longer considered valid and the IC ID can not be used on
the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate Canada authorization.
NOTE IMPORTANT:
End Product Labeling
This transmitter module is authorized only for use in devices where the
antenna may be installed and operated with a minimum distance of 20cm between
the antenna and users. The final end product must be labeled in a visible area
with the following: “Contains IC: 20916-ENET ”.
Manual Information to the End-User
The OEM integrator has to be aware not to provide information to the end-user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end-user manual shall include all required regulatory information/warning
as shown in this manual.
Detachable Antenna Usage
This radio transmitter [IC: 20916-ENET] has been approved by Innovation,
Science, and Economic Development Canada to operate with the antenna types
listed below, with the maximum permissible gain indicated. Antenna types not
included in this list that have a gain greater than the maximum gain indicated
for any type listed are strictly prohibited from use with this device.
Approved antenna(s) list:
Manufacturer| Model| Antenna Type| Max Gain (dBi)|
Impedance (Ω)
---|---|---|---|---
RALTRON| RST-TUA3-TUB7-320020-17M-A-002| Dipole| 3dBi| 50ohm
RALTRON| RST-TUA3-TUB7-19550200-17M-A-001| Dipole| 3dBi| 50ohm
SolarEdge| AS4034-1| Dipole| 0dBi| 50ohm
SolarEdge| AS4035-1| Coil| 0dBi| 50ohm
EU
Hereby, SolarEdge declares that the radio equipment type ENET is in compliance
with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at:
https://www.solaredge.com/sites/default/files/se-single-phase-inverter-
certificate-ce-conformity.pdf
https://www.solaredge.com/sites/default/files/se-single-phase-inverter-
certificate-ce-conformity.pdf
The frequency and maximum transmitted power in the EU are listed below:
863–876 MHz: 17.00 dBm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>