REMARK RK-C2076T-05 Elite Spec 23 Toyota Gr Corolla Installation Guide

: September 12, 2024
: REMARK

Table of Contents

REMARK RK-C2076T-05 Elite Spec 23 Toyota Gr Corolla
Product Usage Instructions
PARTS LIST
PARTS LAY OUT
INSTALLATION
WARRANTY POLICY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

REMARK RK-C2076T-05 Elite Spec 23 Toyota Gr Corolla

Specifications:

Manufacturer: Honda
Year: 2023+
Model: Civic Type R
Trim: FL5
Chassis Code: RK-C3076H-09
Part #: 76C3-H01 (Front Overpipe), 76C3-H02 (Midpipe), 76C2-01 (Muffler)
Description: Catback Configuration with Front Overpipe – 3.0 in / 304 Stainless Steel Construction / Triple Tips

Product Usage Instructions

Installation should be done by a trained technician.
Ensure the exhaust is cool before starting the installation.
Check that the exhaust valve flap is closed visually.
Remove the rear diffuser cover(s).
Disconnect the electrical harness from the exhaust valve motor.
Remove the lower front under cover to access the front overpipe.
Install the REMARK front overpipe using gasket [1] and OEM nuts, torque to factory spec.
Install the exhaust components [B], [C], [D] starting from the front and working rearwards.
Use gaskets and hardware provided to install each section snugly.
Remove the OEM exhaust valve motor and spring.
Adjust the height of the additional spring if needed.
Visually check to ensure the REMARK exhaust valve is closed.
Align the exhaust valve motor spring to the slots on the REMARK exhaust.

FAQ:

Q: Can I install this product myself?
A: We recommend installation by a trained technician for proper installation and to avoid any issues.
Q: Do I need to adjust the spring included in the kit?
A: Only adjust and use the additional spring if you no longer have your OE spring, and ensure it is adjusted to the correct height.

MANUFACTURER: HONDA
YEAR: 2023+
MODEL: CIVIC
TRIM: Type R
CHASSIS CODE: FL5
REMARK PART #: RK-C3076H-09
DESCRIPTION: CATBACK CONFIG. + FRONT OVERPIPE – 3.0 IN / 304 STAINLESS STEEL CONSTRUCTION / TRIPLE TIPS

PARTS LIST

No.	Description	Part Num.	Qty	Torque
1	3.0” Composite 3-Bolt Triangle Gasket	76C3-H01	1
2	3.0” Composite 3-Bolt Triangle Gasket	76C3-H02	1
3	3.0” Compostie 2-Bolt Gasket	76C2-01	2
4	M10x1.5 Serrated Hex Head Bolt L=35mm	M10B35	7	~42 ft-lbs.
5	M10x1.5 Serrated Nut	M10N	7	~42 ft-lbs.
6	M5 Hex Head Bolt	N/A	3	~35 INCH-lbs.
7	M5 Nut	N/A	3	~35 INCH-lbs.
A	3.0” Front overpipe with flex	N/A	1
B	3.0” Resonated section of Midpipe	N/A	1
C	3.0” Rearward section of Midpipe	N/A	1
D	Rear Triple tip muffler section	N/A	1

ITEMS NOT TO SCALE – FOR REFERENCE ONLY

PARTS LAY OUT

INSTALLATION

IMPORTANT: INSTALLATION OF THIS PRODUCT REQUIRES MODIFICATION OR REPLACEMENT OF OEM REAR BUMPER LOWER COVER/ DIFFUSER

We recommend installation to be performed by a trained and/ or qualified technician
Installation should be performed when the exhaust is cool to the touch
Visually ensure the exhaust valve flap is in the closed position
Remove the rear diffuser cover(s)
Disconnect the electrical harness from the exhaust valve motor, and unclip harness from exhaust
Remove the lower front under cover to gain access to the front overpipe
Remove OEM front overpipe and exhaust
Install the original rubber hangers from the OEM exhaust component onto the REMARK exhaust system
Install the REMARK front overpipe onto the vehicle using gasket [1] and the oem nuts. Torque to factory spec.
Begin to install the components of the exhaust [B] [C] [D]. It may be easier to install the exhaust in sections instead of as an assembled complete exhaust due to the weight and size (unless you are installing with aid of an additional person). We recommend starting from the front first and working your way rearwards, starting with [B]
Install the forward section of the midpipe [B] to the REMARK front overpipe. Use provided 3-bolt gasket [2] and provided M10 hardware [4] [5]. Snug or just hand tighten hardware at this point
Use the supplied gasket [3] and hardware [4] [5] to install section [C]. Leaving the hardware hand tight until the entire system is installed.
Remove the OEM exhaust valve motor from the OEM exhaust by removing M5 nuts. Once removed, the valve motor spring should be in position similar to image shown. We recommend using the OEM exhaust valve motor spring. An additional spring is included with the kit but the height of the spring needs to be adjusted/ lengthened if used. Only adjust and use if you no longer have your OE spring.
Visually check to ensure the REMARK exhaust valve is closed
Remove the M5 hardware [6] [7] from the exhaust valve brackets located on the rear muffler section of the REMARK exhaust [D]
Align the exhaust valve motor spring to the slots on the REMARK exhaust valve, and slightly rotate to line up the three mounting tabs.
IMPORTANT – Ensure the spring is properly seated into the slots on the top of the valve motor.
Secure with supplied M5 hardware [6] [7]. 4mm HEX wrench and 8mm box wrench.
CAUTION – Do not overtighten hardware. Suggested, ~35 INCH-lbs.
Install the REMARK rear muffler section [D] onto the vehicle. Use supplied gasket [3] and hardware [4] [5]. Snug the hardware.
Check positioning of the exhaust piping, resonator, muffler(s), and tips(s). Reposition if needed by loosening hardware, adjust position and retighten hardware.
When placement is confirmed, tighten all hardware to recommend torque spec.
INSTALLATION TIP – If the position of the tips need to be adjusted, loosen the flange hardware, have someone hold the tips in desired position, and re-tighten hardware.
Plug in the exhaust valve harness to the exhaust valve motor
Throughly wipe down the exhaust system from any grease, dirt, handprints, fingerprints, etc… as these may cause a permanent stain once the exhaust reaches operating temp. DO NOT USE any harsh cleaners on the polish or burnt
finish tips as permanent discoloration may occur. We recommend soap and water for the tips.
Start the engine and let the system come up to temp.
Check for any leaks, fitment issues, rubbing, etc..
Re-install front lower cover and rear diffuser under panel.
Re-check for exhaust leaks, fitment issues, and re-torque all hardware after ~100 miles of driving.
We highly recommend that the all system components be inspected, and ALL hardware retightened at normal service intervals. Every 3000-5000 miles.

Exhaust Valve Operation –
When stationary and revving, the exhaust valve motor will open regardless of the driving mode.
When driving, Comfort mode will leave the exhaust valve closed. In both Sport and R+ modes, the exhaust valve is predominantly open.

WARRANTY POLICY

1-year limited manufacturer defect warranty from date of purchase
All warranty claims are subject to inspection by REMARK at our facility
Limited Warranty only applies to the original purchaser of the product
REMARK is not responsible for fitment issues on non-US spec vehicles as all products are developed on US spec models
Product finishes are not covered under warranty and considered wear & tear
No warranty whatsoever will be valid if the defect was caused by abuse, negligence and/or mishandling. That includes weather conditions, natural disasters, any road/off-road conditions, and any accidents/collision you were part of.
Acidic cleaning products or steel wool are not to be used unless by a trained professional. Some chemical cleaning products may damage the product and/or finishes.
Wear and tear (the damage that happens to our product in ordinary use) is not covered by our limited warranty.
Improper installation or misuse of the product may lead to failure and damage to both product and vehicle. The user assumes all responsibility.
All products are intended for use off-public streets and highways. Vehicle manufacturer warranty may be voided should any modification(s) or removal(s) of OEM(factory) components are determined.
Federal and state law may prohibit the removal, modification or rendering of any device affecting vehicle emissions or state regulated decibel limits. It is the customer’s responsibility to be aware of federal, state and local laws.
User assumes all cost and risks associated with purchase and installation of aftermarket components. REMARK is not responsible for any fees, fines, or any type of penalties you have received from any authority.
Buyers are responsible for all return shipping fees unless otherwise noted
REMARK does not cover any installation, un-installation, labor fees, or related