ULINE H-1133 Plastic Folded Towel Dispenser Instruction Manual

June 7, 2024
ULINE

H-1133
PLASTIC FOLDED TOWEL DISPENSER

1-800-295-5510
uline.com

ULINE H-1133 Plastic Folded Towel Dispenser - Cover

TOOLS NEEDED

ULINE H-1133 Plastic Folded Towel Dispenser - Tools
Needed

PARTS

ULINE H-1133 Plastic Folded Towel Dispenser - Parts

OPTIONAL PUSH-BUTTON INSTRUCTIONS

  1. Open dispenser and raise end of lock spring just enough to pop out decorative hole plug. (See Figure 1)
    NOTE: Do not overstress the lock spring.
    ULINE H-1133 Plastic Folded Towel Dispenser - Optional Push Button
Instructions 1

  2. Slide push button under lock spring and insert button through hole in door. (See Figure 2)

  3. Release lock spring and close dispenser. (See Figure 2)
    ULINE H-1133 Plastic Folded Towel Dispenser - Optional Push Button
Instructions 2

DECORATOR STRIP INSTALLATION INSTRUCTIONS

  1. Open cover to expose inside of decorator strip window.
  2. Slide decorator strip into place, making sure the decorator strip is held by the plastic guides. (See Figure 3)
  3. Close cover firmly and lock.
    ULINE H-1133 Plastic Folded Towel Dispenser - Decorator strip installation
Instructions

MOUNTING INSTRUCTIONS

NOTE: Recommended mounting height is 48-54″ from the floor to bottom of dispenser.
NOTE: Ensure that proper mounting hardware is used for appropriate wall composition as enclosed hardware may not be compatible with your wall surface.

  1. Insert the key into the lock opening on the top of dispenser and push until cover pops open. If push button is installed, gently push the button until the cover opens. (See Figure 4)
    ULINE H-1133 Plastic Folded Towel Dispenser - Mounting Instructions
1

  2. Open dispenser cover and hold dispenser to ideal mounting place on wall. (See Figure 5)
    ULINE H-1133 Plastic Folded Towel Dispenser - Mounting Instructions
2

  3. Mark the four holes on the wall where screws will be inserted. (See Figure 6)
    ULINE H-1133 Plastic Folded Towel Dispenser - Mounting Instructions
3

  4. Drill into wall at four marked locations with 1/4″ drill bit. (See Figure 7) Insert wall anchors if necessary.
    ULINE H-1133 Plastic Folded Towel Dispenser - Mounting Instructions
4

  5. Hold dispenser over previously drilled holes and insert screws. (See Figure 8)
    ULINE H-1133 Plastic Folded Towel Dispenser - Mounting Instructions
5

LOADING INSTRUCTIONS

CAUTION: Do not overload dispenser.
NOTE: It is recommended that this dispenser be refilled when towels reach the center of the side lens. (See Figure 4)
NOTE: Dispenser will accept C-fold, multi-fold, or Scottfold® paper towels.

LOADING MULTI-FOLD TOWELS

  1. When loading multi-fold towels, make sure that folded edge is down and toward rear of dispenser. (See Figure 9)
    ULINE H-1133 Plastic Folded Towel Dispenser - Loading Instructions
1

LOADING C-FOLD TOWELS

  1. When loading C-fold towels, make sure that folded edge is down. (See Figure 10)
    ULINE H-1133 Plastic Folded Towel Dispenser - Loading Instructions
2

LOADING SCOTTFOLD® TOWELS

  1. When loading Scottfold® towels, make sure short folded edge is down and facing forward through dispenser opening. (See Figure 11)
    ULINE H-1133 Plastic Folded Towel Dispenser - Loading Instructions
3

1-800-295-5510
uline.com

0721 IH-1133

Documents / Resources

| ULINE H-1133 Plastic Folded Towel Dispenser [pdf] Instruction Manual
H-1133, Plastic Folded Towel Dispenser
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals