TSI NI-100 Noise Indicator User Manual
- June 7, 2024
- tsi
Table of Contents
TSI NI-100 Noise Indicator
Warranty
(For country-specific terms and conditions outside of the USA, please visit
www.tsi.com.)
Seller warrants the goods, excluding software, sold hereunder, under normal
use and service as described in the operator’s manual, to be free from defects
in workmanship and material for 12 months, or if less, the length of time
specified in the operator’s manual, from the date of shipment to the customer.
This warranty period is inclusive of any statutory warranty. This limited
warranty is subject to the following exclusions and exceptions:
- Hot-wire or hot-film sensors used with research anemometers, and certain other components when indicated in specifications, are warranted for 90 days from the date of shipment;
- Pumps are warranted for hours of operation as set forth in product or operator’s manuals;
- Parts repaired or replaced as a result of repair services are warranted to be free from defects in workmanship and material, under normal use, for 90 days from the date of shipment;
- Seller does not provide any warranty on finished goods manufactured by others or on any fuses, batteries or other consumable materials. Only the original manufacturer’s warranty applies;
- This warranty does not cover calibration requirements, and seller warrants only that the instrument or product is properly calibrated at the time of its manufacture. Instruments returned for calibration are not covered by this warranty;
- This warranty is VOID if the instrument is opened by anyone other than a factory authorized service center with the one exception where requirements set forth in the manual allow an operator to replace consumables or perform recommended cleaning;
- This warranty is VOID if the product has been misused, neglected, subjected to accidental or intentional damage, or is not properly installed, maintained, or cleaned according to the requirements of the manual. Unless specifically authorized in a separate writing by Seller, Seller makes no warranty with respect to, and shall have no liability in connection with, goods which are incorporated into other products or equipment, or which are modified by any person other than Seller.
The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS stated herein. NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE. WITH RESPECT TO SELLER’S BREACH OF THE IMPLIED WARRANTY AGAINST INFRINGEMENT, SAID WARRANTY IS LIMITED TO CLAIMS OF DIRECT INFRINGEMENT AND EXCLUDES CLAIMS OF CONTRIBUTORY OR INDUCED INFRINGEMENTS. BUYER’S EXCLUSIVE REMEDY SHALL BE THE RETURN OF THE PURCHASE PRICE DISCOUNTED FOR REASONABLE WEAR AND TEAR OR AT SELLER’S OPTION REPLACEMENT OF THE GOODS WITH NON-INFRINGING GOODS.
TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER OR BUYER, AND THE LIMIT OF SELLER’S LIABILITY FOR ANY AND ALL LOSSES, INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS BASED ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) SHALL BE THE RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE PRICE, OR, AT THE OPTION OF SELLER, THE REPAIR OR REPLACEMENT OF THE GOODS. IN THE CASE OF SOFTWARE, SELLER WILL REPAIR OR REPLACE DEFECTIVE SOFTWARE OR IF UNABLE TO DO SO, WILL REFUND THE PURCHASE PRICE OF THE SOFTWARE. IN NO EVENT SHALL SELLER BE LIABLE FOR LOST PROFITS, BUSINESS INTERRUPTION, OR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENTAL DAMAGES. SELLER SHALL NOT BE RESPONSIBLE FOR INSTALLATION, DISMANTLING OR REINSTALLATION COSTS OR CHARGES. No Action, regardless of form, may be brought against Seller more than 12 months after a cause of action has accrued. The goods returned under warranty to Seller’s factory shall be at Buyer’s risk of loss, and will be returned, if at all, at Seller’s risk of loss.
Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY AND LIABILITY, which contains the complete and exclusive limited warranty of Seller. This LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or its terms waived, except by writing signed by an Officer of Seller.
Service Policy
Knowing that inoperative or defective instruments are as detrimental to TSI as
they are to our customers, our service policy is designed to give prompt
attention to any problems. If any malfunction is discovered, please contact
your nearest sales office or representative, or call TSI’s Customer Service
department at 1-800-680-1220 (USA) or
+001 651-490-2860 (International).
Trademarks
TSI and TSI logo are registered trademarks of TSI Incorporated in the United
States and may be protected under other country’s trademark registrations.
Contact/Service information
This section gives directions for contacting TSI® Incorporated for technical information and directions for returning the NI-100 Noise Indicator for service.
Technical Support Contacts
If you have any difficulty setting or operating the instrument, or if you have technical or application questions about this system, contact TSI®s Technical Support.
technical.services@tsi.com
tsigmbh@tsi.com
Service Contact Information
If your instrument does not operate properly, or if you are returning the
instrument for service, visit our website at
tsi.com/service for a Service Request form, or
contact Customer Service.
Returning for Service
Visit our website at tsi.com/service and complete
the on-line “Service Request” form or call TSI® at
1-800-680-1220 (USA) or
651-490-2860, or 001 651 490 2860
(International) for specific return instructions.
Customer Service will need the following information:
- The instrument model number
- The instrument serial number
- A purchase order number (unless under warranty)
- A billing address
- A shipping address
Use the original packing material to return the instrument to TSI®. If you no longer have the original packing material, seal off any ports to prevent debris from entering the instrument and ensure that the display and the connectors on the instrument front and back panels are protected. This instrument is very fragile and must be packed in a manner appropriate for a precision instrument.
- A: Clip
- B: Green LED
- C: Red LED
- D: On/Off Button
OPERATING INSTRUCTIONS
-
Attach the Noise Indicator to clothing where it is clearly visible using badge clip.
-
To switch On, press and hold On/Off button until solid red and green lights appear and then release button.
During use:
Flashing Green, with 2 second intervals indicates noise level below 85 dB(A).
Flashing Red, with 2 second intervals indicates noise level above 85 dB(A). -
To switch Off, press and hold On/Off button until LEDs illuminate solid red and green and then disappear. Release the button.
NOTE: If not manually switched off the noise indicator will automatically power off after approximately 10 hours.
Charging Instructions
-
Plug mini-USB cable from PC into external port of TSI® NI-100 Noise Indicator.
The LED lights will flash alternately red and green.
Allow at least 4 hours to fully charge the battery. -
When fully charged the green LED will double flash every 5 seconds.
WARNING: The NI-100 Noise Indicator is a simple noise check indicator
designed to help the wearer understand when hearing protectors need to be worn
in a workplace environment. This device is not approved for use as a
monitoring device for the purpose of compliance with European Directive
2003/10/EC as part of a risk assessment.
This product complies with the European EMC Directive 2004/108/EC.
Do not use in explosive atmospheres.
Professional advice should be obtained from a safety officer or an
occupational hygienist. For further information call TSI® Incorporated
1-800-680-1220 (USA) or +1
651-490-2860.
TECHNICAL SPECIFICATION
- Size: 5.1cm x 3.6cm x 1.3cm
- Weight: 17g
- {Date of Manufacture \Operating and Storage Temperature: -10 to +50°C }
- Humidity Range: <95%
- Accuracy: ±3dB
- Battery: Lithium Polymer
- Battery Duration: Approximately 200 hours of operating before recharging required.
- Battery Life: Approximately 2 years of charging cycles.
- Charging: A mini-USB cable (Sold Separately).
TSI Incorporated – Visit our website www.tsi.com for more information.
USA Tel: +1 800 680 1220
UK Tel: +44 149 4 459200
France Tel: +33 1 41 19 21 99
Germany Tel: +49 241 523030
India Tel: +91 80 67877200
China Tel: +86 10 8219 7688
Singapore Tel: +65 6595 6388
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>