ULINE H-1713, H-2770 Take-A-Number Wireless System Installation Guide

June 7, 2024
ULINE

ULINE H-1713, H-2770 Take-A-Number Wireless System Installation Guide

TOOLS NEEDED

Large Flathead Screwdriver

Mini Flathead Screwdriver

Phillips Screwdriver

PARTS

COUNT PIECES BEFORE ASSEMBLING

CONTENTS OF MEDIUM BOX (Dispenser)

CONTENTS OF A SMALL BOX (Wireless Push Button Set)

Display Wall Mount Bracket x 1

Wireless Receiver x 1

Wireless Push Button x 2
NOTE: Spare wireless push button in plastic bag is not programmed. See page 6 for programming instructions.

“Please Take A Number” Sign x 1

Label Sheet x 1

CONTENTS OF LARGE BOX (Display)

Display x 1 (H-1713)                  Display x 1 (H-2770)

Wall Anchor x 2                      Large Phillips Screw x 2

CONTENTS OF LARGE RECLOSABLE BAG (Stand and Power Supply)

Power Extension Cable (10 ft.)               AC Power Supply x 1

Country Outlet Adapter x 4

Allen Wrench x 1 (used to disconnect bottom base from stand post)
Mounting Stand x 1

OPERATION AND USE OF DISPENSER

OPERATION
  1. Customer takes a number from the dispenser and waits until the number appears on the display.
  2. Press (+) on the wireless push button once to display the next time
  3. Press and hold (+) on the wireless push button to advance the numbers by tens
  4. Use (–) on the wireless push button to go back one number at a TIME

NUMBER DISPENSER

Number dispenser can be mounted to either the wall or stand.

WALL MOUNTING
  1. Mark mounting holes on wall using dispenser mounting bracket as a (See Figure 1)

  2. Drill holes using 3⁄16″ to 5⁄16″ drill bit.

  3. Use wall anchors if attaching to surfaces other than solid
    Figure 1

  4. Position sign and dispenser mounting bracket (longer holder at the top) over holes in wall and fasten with two slotted screws.
    (See Figure 2)

  5. Snap dispenser into mounting
    (See Figure 3)

STAND MOUNTING
  1. Position mounting stand in the desired location on countertop.

NOTE: for clean, smooth surfaces, remove backing from adhesive strips on the base of the mounting stand and secure to surface.

NOTE: for permanent mounting, use the base of mounting stand as a template, mark and drill four holes and secure base of stand to surface with four screws (not included).

  1. Align holes in sign and mounting bracket (longer holder on top) with holes in Push two large slotted bolts through bracket and sign and secure with nuts. (See Figure 4)
  2. Snap dispenser into mounting (See Figure 3)
LOADING DISPENSER
  1. Pull down locking bar to open dispenser.

  2. Drop in number roll (not included) so the numbers roll out from the bottom. (See Figure 5)

  3.  Pull end of roll through end of dispenser. Close dispenser and snap locking bar back into place.

DISPLAY – MOUNTING AND INSTALLATION

ELECTRONIC DISPLAY

MOUNTING BRACKET TO WALL

  1. Determine where to place the display so it is easily seen by costumers.

  2. Mark mounting holes on wall using the display wall mount bracket as a (See Figure 6)

  3. Drill holes using 5⁄16″ drill bit.

  4. Use wall anchors (included) if attaching to surfaces other than solid wood

  5. Position display wall mount bracket over drilled holes and fasten with two large Phillips (See Figure 7)

CONNECTING AC POWER SUPPLY

  1. Plug the AC power supply into either of the two power receptacles located on the back of the display. (See Figure 8)

  2. Choose the appropriate country outlet adapter and slide it into the AC power (See Figure 9)

  3. Attach 10 power extension cable if necessary. (See Figure 10)

  4. Plug the AC power supply into the nearest outlet.

CONNECTING WIRELESS RECEIVER

  1. Place the pin connector of the wireless receiver on the pins located on the back of (See Figure 11)
  2. Remove backing from adhesive strips on the wireless receiver and mount it on the back of the display.

SETUP

SETTING SOUND TONE AND VOLUME

Use a mini flathead screwdriver to change the tone and volume switches on back of the display. (See Figure 12) Set the sound tone with switches 1-2:

  • No sound: 1-OFF, 2-OFF
  • Single tone: 1-OFF, 2-ON
  • Double tone: 1-ON, 2-OFF
  • Triple tone: 1-ON, 2-ON

Set the volume with switches 3-4:

  • Low volume: 3-OFF, 4-OFF
  • Medium volume: 3-ON, 4-OFF (recommended in most cases)
  • High volume: 3-OFF, 4-ON
  • Highest volume: 3-ON, 4-ON

DISPLAY START-UP

The display shows a number of messages on start-up once it is plugged in. (See Figure 13) Display shows:

  • Program version: “P-“, then number
  • TOM-Net address: ‘ad”, then 51 or 21
  • Last number displayed when power was disconnected: Number, (“00” if first-time start-up.)
  • Error message if display is set as a duplicate master: “Ed”

OPTIONAL DISPLAY SETUP (See Figure 14)

To enter setup options, make sure display is unplugged. Hold down (+) on the wireless push button and plug the display back in. Release (+) when display shows “UP.”

  1. Set display update delay:
    • Display shows “UP” followed by the current delay time in seconds, (ex. “00”). Press (+) on the wireless push button to increase the delay one second at a
    • After three seconds without pushing the button, the set display sleep time “SL”
  2. Set display sleep time:
    • Display shows “SL” followed by the current setting in (The display shuts off after a set period of time with no button pushes.) Press (+) on the wireless push button to increase the delay before the display goes into sleep mode one minute at a time.
    • After three seconds without pushing the button, the set display flashes and “FL” appears.
  3. Set display flashes when number changes:
    • Display shows “FL” followed by the current setting showing number of flashes. Press (+) on the wireless push button to increase the number of times the display will flash when the number changes one flash at a time.
  4. After three seconds without pushing the button, the display shows “CS” and saves new settings to memory.

INSTALLING ADDITIONAL DISPLAYS

  • See instructions included with H-2769 or H-4665.

PROGRAMMING  WIRLES PUSH  BUTTON

NOTE: The wireless push button codes must be copied to the wireless receiver. The maximum number of wireless push buttons per wireless receiver is 15.

NOTE: Individual wireless push button codes cannot be changed or deleted. All codes must be deleted to start over with new codes.

PROGRAMMING ADDITIONAL WIRELESS PUSH BUTTON
  1. Press #1 on the wireless receiver and hold for three The green LED light on the back of the wireless receiver will start blinking. (See Figure 15)
  2. Release #1 on the wireless receiver. Then press the (+) button on the wireless push button. The green LED light will stop blinking. (See Figure 16)
  3. Press #2 on the wireless receiver and hold for three The red LED light on the back of the wireless receiver will start blinking. (See Figure 15)
  4. Release #2 on the wireless receiver. Then press the (–) button on the wireless push button. The red LED light will stop (See Figure 16)

DELETING WIRELESS PUSH BUTTON

  1. Press #1 on the wireless receiver for three seconds. Release and press #1 again for three seconds. The code has been (See Figure 15)
  2. Press #2 on the wireless receiver for three seconds. Release and press #2 again for three seconds. The code has been (See Figure 15)

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals