AcuRite 00617 Pool & Spa Thermometer Instruction Manual
- June 7, 2024
- Acurite
Table of Contents
Instruction Manual
Pool & Spa Thermometer
model 00617
Questions? Contact Customer Support at
877-221-1252 or visit
www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Congratulations on your new AcuRite product. To ensure the best possible product performance, please read this manual in its entirety and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this product. Locate the tab and peel it off to remove it.
Package Contents
- Display unit with tabletop stand
- Pool and spa temperature sensor
- Instruction Manual
Features & Benefits
TEMPERATURE SENSOR
-
High-Temperature Record
The highest temperature was recorded over the past 24 hours. -
Low-Temperature Record
The lowest temperature was recorded over the past 24 hours. -
Integrated Anchor Loop for easy placement.
-
Sensor Low Battery Indicator
-
Current Temperature
BOTTOM OF SENSOR -
A-B-C Switch
ID code that must match display’s A-B-C switch to ensure units synchronize. -
Battery Compartment
-
°C/°F Button
Press to select° C or °F temperature units. -
Battery Compartment Ring for securing the battery compartment to the sensor.
-
Battery Compartment Housing
Features & Benefits
DISPLAY UNIT
-
High-Temperature Record
The highest water temperature was recorded over the past 24 hours. -
Current Temperature
-
Low-Temperature Record
The lowest water temperature was recorded over the past 24 hours. -
History Chart
Displays the past 72 hours of data for temperature. -
“ “ Icon
Displays when FREEZE WARNING is active. -
“▼ CLEAR MIN“ Button
Press and release to clear low-temperature record (#3). -
“ FREEZE WARNING“ Button
Press to activate freeze warning. -
“ ▲ CLEAR MAX“ Button
Press and release to clear high-temperature record (#1). -
Display Low Battery Indicator
-
Sensor Signal Strength
-
Sensor Low Battery Indicato r
BACK -
Integrated Hang Hole
For easy wall mounting. -
A-B-C Switch
ID code that must match sensor’s A-B-C switch to ensure units synchronize. -
Battery Compartment
-
Removable Tabletop Stand
-
°C/°F Button
Press to select ° C or ° F temperature units. -
Battery Compartment Cover
SETUP
Sensor Setup
-
Access Battery Compartment
Remove the battery compartment housing from the sensor by unscrewing the battery compartment ring. -
Set the A-B-C Switch
The A-B-C switch is located inside the battery compartment. It can be set to A, B or C. However, you must select the same letter choices for both the sensor and the display unit in order for the units to synchronize. -
Install or Replace Batteries
Remove the battery compartment housing from the sensor by unscrewing the battery compartment ring.
AcuRite recommends high-quality alkaline batteries for the best product performance. Heavy duty or rechargeable batteries are not recommended.
Slide off the battery compartment cover. Take note of the A-B-C switch setting inside the battery compartment.
1. Insert 2 x AA batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment.
2. Replace the battery cover. -
Replace Battery Compartment Housing
Replace battery compartment housing and secure to the sensor by screwing on the battery compartment ring.
IMPORTANT: Screw on the battery compartment ring gasket tightly, to ensure that water does not enter the sensor and damage its internal components.
Display Unit Setup
-
Set the A-B-C Switch
Locate the A-B-C switch inside the battery compartment. Set the A-B-C switch to A, B or C. You must select the same letter choices for both the display unit and the sensor in order for the units to synchronize. -
Install or Replace Batteries
1. Remove the battery compartment cover.
2. Insert 3 x AA alkaline batteries into the battery compartment, as shown. Follow the polarity (+/-) diagram in the battery compartment.
3. Replace the battery cover.
Select Temperature Units
To select between degrees Celsius (°C) or Fahrenheit (°F) temperature units,
slide the “°C/ °F” switch located inside the battery compartment located on
the back of the display.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY
AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior
to battery installation. Remove batteries from equipment that is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the
battery compartment. Promptly remove dead batteries from the device. Dispose
of used batteries properly. Only batteries of the same or equivalent type as
recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose
of batteries in fire, as batteries may explode or leak. DO NOT mix old and new
batteries or types of batteries (alkaline/standard). DO NOT use rechargeable
batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit
the supply terminals.
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of both the display unit and outdoor sensor are critical to the
accuracy and performance of this product.
Display Unit Placement
Place the display unit in a dry area free of dirt and dust.
The display unit stands upright for tabletop use or is wall-mountable.
Outdoor Sensor Placement
Sensors must be placed in water to observe water temperature. The sensor
should be secured to a pool ladder or other structure to prevent it from
drifting out of the wireless range of the display unit. Secure the sensor
using the integrated anchor loop and a length of waterproof cord or rope (not
included).
Important Placement Guidelines
- The display unit and outdoor sensor must be within 100 ft (30 m) of each other.
- To maximize wireless range, place units away from large metallic items, thick walls, metal surfaces, or other objects that may limit wireless communication.
- To prevent wireless interference, place both units at least 3 ft (.9 m) away from electronic devices (TV, computer, microwave, radio, etc.).
Setup is Complete
The sensor will now synchronize with the display unit. It may take a few
minutes for synchronization to complete. Please refer to the troubleshooting
section of this manual if anything appears to be functioning improperly.
OPERATION
Using the Thermometer
Water Temperature History Chart
The water temperature history chart lets you monitor the change in conditions
over the past 3 days (-3, -2, -1) and over the past 16 hours (-16, -8, -6, -4,
-2, -1, 0).
Set the Freeze Warning Alarm
Press the FREEZE WARNING button to activate the freeze alarm. ” FREEZE WARNING
ON ALARM WILL SOUND” will appear on the display.
Deactivate the freeze alarm by pressing the FREEZE WARNING button again.
Freeze Warning Alarm Function
The freeze warning alarm will sound and the display will flash when the
temperature drops below 40°F (4°C). The alarm will sound for up to 1 minute.
When the alarm is sounding, press any button to silence the alarm. If no
buttons are pressed, the alarm will automatically stop after 1 minute and the
display will continue to flash for up to 10 hours.
High/Low Records
High and low values are recorded for water temperature. High and low records
reflect the minimum and maximum temperature records in the last 24 hours,
starting at the time the batteries are installed.
To clear the LOW-temperature record, press and release the “▼ CLEAR MIN”
button. button. Dashes will display to confirm low record has been cleared. To
clear the HIGH-temperature record, press and release the “▲ CLEAR MAX” button.
Dashes will display to confirm high record has been cleared.
Troubleshooting
No outdoor sensor reception no bars| If the wireless signal indicator shows no
bars:
• Relocate the display unit and/or the outdoor sensor.
The units must be within 100 ft (30 m) of each other.
• Make sure both units are placed at least 3 feet (.9m) away from electronics
that may interfere with the wireless communication (such as TVs, microwaves,
computers, etc).
• Use standard alkaline batteries. Do not use heavy-duty or rechargeable
batteries. NOTE: It may take up to 20 minutes for the display unit and sensor
to synchronize after batteries are replaced.
---|---
Display screen not working| • Check that the batteries are installed
correctly. Batteries may need to be replaced.
Temperature is flashing or showing dashes| Flashing of the temperature is
generally an indication of wireless interference.
1. Bring both the sensor and display unit indoors and remove at least one
battery from each.
2. Make sure the A-B-C switch on both units matches.
3. Reinstall the battery in the outdoor sensor.
4. Reinstall the battery in the display unit.
5. Let the units sit within a couple of feet of each other for about 20
minutes to gain a strong connection.
If your AcuRite product does not operate properly after trying the troubleshooting steps, visit www.AcuRite.com or call 877-221-1252 for assistance.
Care & Maintenance
Display Unit Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt, and moisture.
Outdoor Sensor Care
Clean with a soft damp cloth. Do not use caustic cleaners or abrasives.
Specifications
| TEMPERATURE RANGE | 32ºF to 158ºF; 0ºC to 70ºC |
|---|---|
| WIRELESS RANGE | 100 ft / 30 m depending on home construction materials |
| OPERATING FREQUENCY | 433 MHz |
| POWER | Display: 3 x AA alkaline batteries |
Sensor: 2 x AA alkaline batteries
DATA REPORTING| 60-second updates
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
- This device may NOT cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Customer Support
AcuRite customer support is committed to providing you with best-in-class service. For assistance, please have the model number of this product available and contact us in any of the following ways:
877-221-1252
info@chaney-inst.com
24/7 support at www.AcuRite.com
► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas
Limited One Year Warranty
At AcuRite, we proudly uphold our commitment to quality technology. Chaney
Instrument Co. warrants that all products it manufactures to be of good
material and workmanship and to be free of defects when properly installed and
operated for a period of one year from the date of purchase.
We recommend that you visit us at www.AcuRite.com
for the fastest way to register your product. However, product registration
does not eliminate the need to retain your
original proof of purchase in order to obtain warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures to be of good
material and workmanship and to be free of defects when properly installed and
operated for a period of one year from the date of purchase. Remedy for
breach of this warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is proven to breach
the warranty contained herein within ONE YEAR from the date of sale will, upon
examination by Chaney, and at its sole option, be repaired or replaced by
Chaney. Transportation costs and charges for returned goods shall be paid for
by the purchaser. Chaney hereby disclaims all responsibility for such
transportation costs and charges. This warranty will not be breached, and
Chaney will give no credit for products it manufactures which have received
normal wear and tear, been damaged (including by acts of nature), tampered,
abused, improperly installed, damaged in shipping, or repaired or altered by
others than authorized representatives of Chaney.
The above-described warranty is expressly in lieu of all other warranties,
express or implied, and all other warranties are hereby expressly disclaimed,
including without limitation the implied warranty of merchantability and the
implied warranty of fitness for a particular purpose. Chaney expressly
disclaims all liability for special, consequential or incidental damages,
whether arising in tort or by contract from any breach of this warranty. Some
states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. Chaney
further disclaims all liability from personal injury relating to its products
to the extent permitted by law. By acceptance of any of Chaney’s products, the
purchaser assumes all liability for the consequences arising from their use or
misuse. No person, firm or corporation is authorized to assume for Chaney any
other liability in connection with the sale of its products. Furthermore, no
person, firm, or corporation is authorized to modify or waive the terms of
this paragraph, and the preceding paragraph, unless done in writing and signed
by a duly authorized agent of Chaney. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
For in-warranty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
It’s more than accurate, it’s AcuRite offers an extensive assortment of precision instruments, designed to provide you with information you can depend on to Plan your day with confidence™.
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.
Printed in China
00617 INST 012215
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>