DNAKE S215 Door Station User Guide

June 5, 2024
DNAKE

DNAKE S215 Door Station User Guide
DNAKE S215 Door Station

REMARK

Please follow the user manual for correct installation and testing. If there is any doubt please call our tech-supporting and customer center.

Our company applies ourselves to reformation and innovation of our products. No extra notice for any change. The illustration shown here is only for reference. If there is any difference, please take the actual product as the standard.

The product and batteries must be handled separately from household waste. When the product reaches the end of service life and needs to be discarded, please contact the local administrative department and put it in the designated collection points in order to avoid the damage to the environment and human health caused by any disposal. We encourage recycling and reusing the material resources.

For specific operation instructions, please scan the following QR code to obtain the full version of the User Manual.

PACKAGE CONTENTS

Please make sure the package contains the following items :

  • Door Station

  • Screw

  •  Screw Fixing Seat

  •  Screw Wrench

  •  Interface Plate

  • Cable Locking Plate

  • Hanging Rope

  • Sealing Plug

  •  Quick Start Guide

PICTURES

BASIC OPERATION

Calling indoor monitor

In a standby mode, input room number on door station, for example, when inputting “123” on door station, then press “if” to enter the call state. Note: During communication, pressing “s” on the door station, the call gets disconnected.

Phonebook

In a standby mode, press “ ” or “ ” button on the keypad to open phonebook page. Select and press “#” or “ ” on the keypad to call.

Unlock the door

Unlocking by PIN Code

In a standby mode, press “#” key and enter the PIN Code(default is 0000). Then press “#” key again to confirm. If the PIN Code is correct, the door will be unlocked; if not, it will make a sound like “clatter clatter”.

Unlocking by IC/ID card

Put the registered IC/ID card on card reader area of the door station. If successful, the door will be unlocked.

Calling concierge

In a standby mode, press “ ” to call concierge directly. During ringing, press “*” key to cancel the call.

SYSTEM CONFIGURATION

SYSTEM CONFIGURATION

SYSTEM DIAGRAM

  1. Network(PoE)
    Standard RJ45 interface connects with master station, indoor monitor or other network equipment by network switch.
    Network\(PoE\)

  2. Power
    Power interface of door station connects with 12V DC power.
    Power Induction

  3. Switching Value Output
    Connect to the lock module ( independent power supply is necessary for the lock)
    Switching Value Output

  4. RS485
    Enable to connect equipment with RS485 interface.
    RS485 Connecting

  5. Exit/Door-detector/Fire Fighting Linkage
    Exit Door Detector

  6. Card Reader Interface The interface can be connected to one IC/ID card reader or be used for reading the information of built-in card reader.
    Card Reader Interface

Note: Only one card reader can be connected to door station. When there is built-in card reader, the interface can only be used for reading the information of built-in card reader.

INSTALLATION

Model: S215 ( Flush Mounting )

Installation Induction

  • Product size: 133x295x41mm
  • Flush mounting box size: 122x287x55mm
  • Trepanning size: 124x289x56mm

MODEL: S215 ( Surface Mounting )

  • Product Size: 133 x 295 x 41mm
  • Surface mounting box size : 132 x 294 x 34.5mm
Installation method
  1. According to the installation dimension of door station, dig a square groove at the appropriate position in the wall or door, and dig a hole (drainage hole) at the bottom;
  2. Drill the threading holes at the bottom of the built-in box to facilitate drainage. Upward arrow is on the front of the built-in box. Embed the built-in box into the wall, then put the built-in box into the groove of the wall, and tighten four screws from top to bottom of the built-in box, or fix the built-in box in the wall with concrete;
  3. Assemble the door station into the built-in box, align the groove and the built-in box, tighten the screws, and finally inject the glass glue into the top, left and right sides of the door station(note: the glass glue cannot be injected into bottom part that is reserved for the drainage hole at the bottom of door station).
Installation Instruction

[Suggestion]: The camera should be 1450— 1550mm above the ground. Th camera at this height can capture human face perfectly.

SAFETY INSTRUCTIONS

In order to protect you and others from harm or your device from damage, please read the following information before using the device.

Do not install the device in the following places:

  • Do not install the device in high-temperature and moist environment or the area close to magnetic field, such as the electric generator, transformer or magnet.
  • Do not place the device near the heating products such as electric heater or the fluid container.
  • Do not place the device in the sun or near the heat source, which might cause discoloration or deformation of the device.
  • Do not install the device in an unstable position to avoid the property losses or personal injury caused by the falling of device.

Guard against electric shock, fire and explosion:

  • Do not use damaged power cord, plug or loose outlet.
  • Do not touch the power cord with wet hand or unplug the power cord by pulling.
  • Do not bend or damage the power cord.
  • Do not touch the device with wet hand.
  • Do not make the power supply slip or cause the impact.
  • Do not use the power supply without the manufacturer’s approval.
  • Do not have the liquids such as water go into the device.

Clean Device Surface

  • Clean the device surfaces with soft cloth dipped in some water, and then rub the surface with dry cloth.

Other Tips

  • In order to prevent damage to the paint layer or the case, please do not expose the device to chemical products, such as the diluent, gasoline, alcohol, insect-resist agents, opacifying agent and insecticide.
  • Do not knock on the device with hard objects.
  • Do not press the screen surface. Overexertion might cause flopover or damage to the device.
  • Please be careful when standing up from the area under the device.
  • Do not disassemble, repair or modify the device at your own discretion.
  • The arbitrary modification is not covered under warranty. When any repair required, please contact the customer service center.
  • If there is abnormal sound, smell or fume in the device, please unplug the power cord immediately and contact the customer service center.
  • When the device isn’t used for a long time, the adaptor and memory card can be removed and placed in dry environment.
  • When moving, please hand over the manual to new tenant for proper usage of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals