AcuRite 06014 Home Weather Station Instruction Manual

AcuRite 06014 Home Weather Station

Features & Benefits

1. Rainfall Collector Funnel

2. Solar Cell Panel
   Converts sunlight into power to run the internal aspirating fan.
   Internal Aspirating Fan
   (not shown) Draws ambient air into the sensor to reduce solar radiation heating, resulting in more accurate temperature measurements.

3. A-B-C Switch ID code that must match the display’s A- B-C switch to ensure units synchronize.

4. Battery Compartment

5. Temperature & Humidity Sensors (internal)

6. Mounting Point

7. Wind Speed Anemometer

8. Wind Direction Vane

9. Mounting Bracket

10. Mounting Hardware
    Includes 5 anchors & the following screws: 
    Qty   Diameter  Length
    5          #4             3/4”
    1          #4              1/2”
    1          #6             1/2”

11. Debris Filter
    Pre-installed to prevent debris from entering the rain gauge.

5-in-1 Sensor Setup

• Set the A-B-C Switch
  Locate the A-B-C switch inside the battery compartment. Set the A-B-C to switch to A, B, or C. You must select the same letter choice for both the sensor and the companion unit (not included) in order for the units to synchronize.

• Install or Replace Batteries
  Batteries MUST be installed for this product to operate. AcuRite recommends high-quality alkaline or lithium batteries for the best product performance. Heavy-duty or rechargeable batteries are not recommended. The 5-in-1 sensor requires lithium batteries in low-temperature conditions. Cold temperatures can cause alkaline batteries to function improperly. Use lithium batteries in the 5-in-1 sensor for temperatures below -4ºF / -20ºC.

• Remove the Rain Gauge Stabilizer
  Locate and remove the rain gauge stabilizer (plastic tab) taped to the bottom of the sensor. The rain gauge will not function until this is removed .

PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.

BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment that is not to be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in a fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.

Placement for Maximum Accuracy

AcuRite sensors are sensitive to surrounding environmental conditions. Proper placement of both the display and the sensor is critical to the accuracy and performance of this product.

5-in-1 Sensor Placement

The 5-in-1 sensor is designed to remain outdoors all year long. Choose an open location with no obstructions above or around the sensor for the most accurate measurements.

Important Placement Guidelines

The display and sensor must be within 330 feet (100 meters) of each other.

• MAXIMIZE WIRELESS RANGE
  Place units away from large metallic items, thick walls, metal surfaces, or other objects that may limit wireless communication.

• PREVENT WIRELESS INTERFERENCE
  Place units at least 3 feet (.9 m) away from electronic devices (TV, computer, microwave, radio, etc.).

• LOCATE AWAY FROM HEAT SOURCES
  Position the sensor away from heaters, air conditioners, chimneys, exhaust vents, asphalt and concrete (surfaces that radiate heat).

• LOCATE AWAY FROM HUMIDITY SOURCES
  Avoid installing the sensor near pools, spas, or other bodies of water. Water sources may impact humidity accuracy.

• LOCATE AWAY FROM SPRINKLER HEADS
  DO NOT install the sensor where it will be sprayed by a sprinkler system. This may force water inside the sensor.

• LOCATE AWAY FROM WIND & RAIN OBSTRUCTIONS
  DO NOT mount the sensor with obstructions around it. Consider a location that is a wide open area, with few structures around to ensure accurate wind measurement.

**Visit us online to view installation photos and video, or learn more

about AcuRite technology:** www.AcuRite.com/5in1
5-in-1 Sensor Installation Guidelines

INSTALLATION HEIGHT

Mount the sensor at a minimum height of 5 feet (1.5 meters) off the ground, in an open area. Higher is better for wind measurements – the National Weather Service recommends 33 feet (10 meters) high!

MOUNTING OPTIONS

The included mounting bracket is designed to screw directly onto wooden posts or surfaces that are 2”x 4” or larger. The sensor can also be mounted directly to a 3/4” steel pipe (available at hardware stores and home centers).

SOLAR CELL INSTALLATION

Install the sensor with the solar cell facing SOUTH. This ensures the cell receives as much sun as possible and orients wind direction. 5-in-1 Sensor Installation

1. Fasten the mounting base (included) to a post or pole (not included) using the 4 longer screws included in the hardware bag.
2. Insert the mounting base into the hole on the bottom of the sensor.
3. Make sure the arrows on the top of the sensor are pointed in the proper direction and the bubble level is centered. The solar cell should be facing south to properly orient the wind direction.
4. Fasten the sensor into the mounting base using the 2 shorter screws included in the hardware bag.

The 5-in-1 sensor is now ready to use.

Basic Setup is Complete

The 5-in-1 sensor will now synchronize with the display. It may take a few minutes for synchronization to complete. If both or one of the units appears to be functioning improperly, please refer to the troubleshooting section.

Calibrate the Rain Gauge

The rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy. Items Needed: 5-in-1 sensor, companion unit, plastic cup, pin, screwdriver

1. First, ensure the 5-in-1 sensor is perfectly level using the built-in bubble level.
2. Use a compatible companion unit or AcuRite software to monitor during calibration.
3. Make a pinhole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill it with exactly 1 cup (8oz) of water, allowing the water to drip into the rain gauge. You should hear the internal buckets tip and see water drain through the rain gauge.
4. A few seconds after each bucket tip, the companion unit displays rainfall in approximately 0.01” or more increments.
5. The cup of water should take more than 20 minutes to empty; a quicker period will result in an inaccurate calibration. Try to simulate a normal steady rainfall. When the cup is empty of water, the companion unit should register 1.06”

Tips

There should be nearly an equal number of water drops (about 25 water drops) between bucket tips. If not, adjust the calibration screws on the bottom of the 5-in-1 sensor until an equal number of water drops are tipping the buckets.

Adjustment

If the rain gauge doesn’t register close to 1.06”, make an EQUAL adjustment to the two calibration screws on the bottom of the 5-in-1 sensor. Turning screws clockwise increases rainfall; counter-clockwise decreases rainfall.

• To adjust the rainfall reading by 2% turn both screws 1/8 of a turn.
• To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.
• To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.

Watch the video at www.AcuRite.com/5in1

Specifications

updates Outdoor temperature & humidity: 36-second updates

Customer Support

AcuRite customer support is committed to providing you with best-in-class service. For assistance, please have the model number of this product available and contact us in any of the following ways:

(877) 221-1252

Visit us at www.AcuRite.com

• Installation Videos
• Instruction Manuals
• Replacement Parts
• Register your Product
• Support User Forum
• Submit Feedback & Ideas

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:

• This device may NOT cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

• This device may not cause interference, and
• This device must accept any interference received, including interference that may cause undesired operation of the device.

Limited 1-Year Warranty

AcuRite is a wholly owned subsidiary of Chaney Instrument Company. For purchases of AcuRite products, AcuRite provides the benefits and services set forth herein. For purchases of Chaney products, Chaney provides the benefits and services set forth herein.
We warrant that all products we manufacture under this warranty are of good material and workmanship and, when properly installed and operated, will be free of defects for a period of one year from the date of purchase.

Any product which, under normal use and service, is proven to breach the warranty contained herein within ONE YEAR from the date of sale will, upon examination by us, and at our sole option, be repaired or replaced by us. Transportation costs and charges for returned goods shall be paid for by the purchaser. We hereby disclaim all responsibility for such transportation costs and charges. This warranty will not be breached, and we will give no credit for products that have received normal wear and tear not affecting the functionality of the product, been damaged (including by acts of nature), tampered, abused, improperly installed, or repaired or altered by others than our authorized representatives.

Remedy for breach of this warranty is limited to repair or replacement of the defective item(s). If we determine that repair or replacement is not feasible, we may, at our option, refund the amount of the original purchase price

THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY FOR THE PRODUCTS AND IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. ALL OTHER WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

We expressly disclaim all liability for special, consequential, or incidental damages, whether arising in tort or by contract from any breach of this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. We further disclaim liability for personal injury relating to its products to the extent permitted by law. By acceptance of any of our products, the purchaser assumes all liability for the consequences arising from their use or misuse. No person, firm, or corporation is authorized to bind us to any other obligation or liability in connection with the sale of our products.

Furthermore, no person, firm, or corporation is authorized to modify or waive the terms of this warranty unless done in writing and signed by a duly authorized agent of ours. In no case shall our liability for any claim relating to our products, your purchase, or your use thereof, exceed the original purchase price paid for the product.

Applicability of Policy

This Return, Refund and Warranty Policy applies only to purchases made in the United States and Canada. For purchases made in a country other than the United States or Canada, please consult the policies applicable to the country in which you made your purchase.

Additionally, this Policy applies only to the original purchaser of our products. We cannot and do not offer any return, refund, or warranty services if you buy products used or from resale sites such as eBay or Craigslist.

Governing Law

This Return, Refund and Warranty Policy is governed by the laws of the United States and the State of Wisconsin. Any dispute relating to this Policy shall be brought exclusively in the federal or State courts having jurisdiction in Walworth County, Wisconsin; and the purchaser consents to jurisdiction within the State of Wisconsin.

It’s More than Accurate, it’s AcuRite offers an extensive assortment of precision instruments, designed to provide you with information you can depend on to Plan your day with confidence™.

www.AcuRite.com

©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology. Visit www.AcuRite.com/patents for details.

FREQUENTLY ASKED QUESTIONS

What is the AcuRite 06014 Home Weather Station?

The AcuRite 06014 Home Weather Station is a device that allows you to monitor various weather conditions and receive accurate weather forecasts for your location.

What are the main features of the AcuRite 06014 Home Weather Station?

The main features of the AcuRite 06014 Home Weather Station include temperature and humidity readings, barometric pressure measurements, wind speed and direction monitoring, rainfall measurements, and a digital display for easy reading.

How does the AcuRite 06014 Home Weather Station provide weather forecasts?

The AcuRite 06014 Home Weather Station uses its sensors to collect data on current weather conditions and then utilizes that data to generate accurate local weather forecasts.

Can the AcuRite 06014 Home Weather Station connect to the internet?

No, the AcuRite 06014 Home Weather Station does not have internet connectivity. It is a standalone device that provides localized weather information.

Does the AcuRite 06014 Home Weather Station require batteries?

Yes, the AcuRite 06014 Home Weather Station requires batteries to power the various sensors and the digital display.

Can I view historical weather data with the AcuRite 06014 Home Weather Station?

Yes, the AcuRite 06014 Home Weather Station has the capability to store and display historical weather data, allowing you to track weather patterns over time.

Is the AcuRite 06014 Home Weather Station suitable for outdoor use?

Yes, the AcuRite 06014 Home Weather Station is designed to be used outdoors and can withstand various weather conditions.

Can I set up alerts with the AcuRite 06014 Home Weather Station?

No, the AcuRite 06014 Home Weather Station does not have built-in alert capabilities. It primarily provides weather information and forecasts.

What is the range of the wireless connection between the sensors and the main unit?

The wireless range between the sensors and the main unit of the AcuRite 06014 Home Weather Station is typically around 330 feet (100 meters) when there are no obstructions.

Can I connect additional sensors to the AcuRite 06014 Home Weather Station?

No, the AcuRite 06014 Home Weather Station is not designed to connect additional sensors. It comes with a set of sensors included.

Is the AcuRite 06014 Home Weather Station easy to install?

Yes, the AcuRite 06014 Home Weather Station is generally straightforward to install. It typically involves mounting the sensors in appropriate locations and setting up the main unit.

Does the AcuRite 06014 Home Weather Station have a mobile app?

No, the AcuRite 06014 Home Weather Station does not have a dedicated mobile app. It primarily relies on the digital display for data visualization.

Can I connect the AcuRite 06014 Home Weather Station to a computer for data analysis?

No, the AcuRite 06014 Home Weather Station does not have computer connectivity options. It is primarily designed for standalone use.

How accurate are the measurements provided by the AcuRite 06014 Home Weather Station?

The AcuRite 06014 Home Weather Station is known for providing reasonably accurate weather measurements, but keep in mind that its accuracy may vary based on factors such as sensor placement and calibration.

Can I mount the AcuRite 06014 Home Weather Station on a pole?

Yes, the AcuRite 06014 Home Weather Station can be mounted on a pole using the included mounting hardware. This allows for optimal sensor placement and better accuracy.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK:AcuRite 01540M Home Weather Station Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>