omnicharge OC32B001 Power Station User Manual

: June 7, 2024
: omnicharge

omnicharge OC32B001 Power Station User Manual

WHATS IN THE BOX?

5 or 10 Omni 20+
Omnicharge Power Station
AC Power Cable
User Manual

DEPLOYMENT TIPS

Placing the station in a visible, high traffic location and effectively communicating the availability of the Power Station will help drive higher usage.
If you are you provide self-checkout, make sure the power station either has access to ethernet or a strong wifi connection.

POWER STATION SETUP

Step 1 :
Place the Omnicharges into the open bays with the AC port facing upwards.
Product Overview

Step 2:
Plug the AC power cable into the base of the power station, and connect to power.
Product Overview

OMNI CLOUD SOFTWARE

The Omnicharge Power Station is built on a powerful software platform allowing you to seamlessly manage and control all your Power Stations from the same dashboard.
For more information visit: www.https://www.omnicharge.co/power- station/
Product Overview

TECHNICAL SPECIFICATIONS

GENERAL

Product Name: Omnicharge Power Station
Weight w/ units (5x): 10.9 kg (24.1 lbs)
Weight w/ units (10x): 18.6 kg (41.1 lbs)
Dimensions w/ units (5x): 330mm x 179mm x 250mm (12.9 x 7 x 9.8 in)
Dimensions w/ units (10x): 530 mm x 179 mm x 250 mm (20.8 x 7 x 9.8 in)

INPUT
100V – 240V~, 50/60Hz, up to 10A

OUTPUT
24V 2A (per charging bay

OPERATING ENVIRONMENT
Temperature 0°C-40°C
Humidity 30-70%
Altitude ≤2000m

STORING YOUR POWER STATION

When storing the power station for an extended period of time please adhere to the following guidelines. Failure to do so can cause longterm damage to the battery cells, and may void your warranty.

Store the powerstation in a cool and dry location.
Shut off the power and disconnect the power cable.
Make sure all Omnicharge units are powered off.
Fully recharge all Omnicharge batteries every 3-4 months.

WARNING

Failure to follow these safety instructions can result in fire, electrical shock, injuries, or damage to your Power Station or other property. Read all safety information carefully before using your Power Station.

Do not set up the power station under direct sunlight or near any heat sources like ovens, stoves, etc, as this may cause the Power Station to overheat.

The Power Station must be grounded. Never operate your power station in the absence of a suitably installed ground conductor.

Before you clean your Power Station, disconnect the power and remove and installed Omnicharges. Clean your Power Station with a soft damp cloth, and avoid spraying liquid on the Power Station.

This product is designed for indoor use only. Keep your Power Station dry and away from moisture, flammable gasses or corrosive materials. Do not operate with wet hands.

Do not disassemble this product or attempt to re-purpose or modify it in any manner.

The power cable, like any other metal wire or cable, is subject to becoming weak or brittle if repeatedly bent or crushed in the same spot. To avoid damage, do not place any objects on top of the cable. Do not use the power cable if damaged.

Radio Frequencies
The built-in communication module exchanges data with both the cloud and terminal equipment. The equipment operates at in the 2402Mhz to 2480Mhz frequency band(s). Maximum Wi-Fi power transmitted in the operating frequency is +17.9dBm. Maximum bluetooth power transmitted is +3.9dBm.

PORTS AND BUTTONS

Note: For optimal wireless charging, place phone horizontally towards the back of the Omnicharge.
PORTS AND BUTTONS

AC Outlet
Power and Menu Button
USB Button
AC Outlet Button
Quick Charge USB (QC 3.0 Compatible)
5V/3A USB-A Port
DC Input/Output (5.5 x 2.1mm Barrel Port)
USB-C Input/Output
Wireless Charging

BUTTON FUNCTIONS

PRIMARY CONTROLS

Long press to power on
Long press to power off
On/Off AC Outlet
On/Off USB Ports

MENU CONTROLS

Double press to enter the menu
Quick press to select
Move Up
Move Down

SCREEN

OLED screen with real time metrics

SCREEN

Status Icons
Power Input (watts)
Battery Power Output (watts)
Battery Temperature
DC Output Voltage
Battery Percentage

Note: When you are pass-through charging, the battery output field will show a lower value and can even show 0W output, since the output field is showing how much power is output from the battery and not how much is output from the port.

SCREEN ICONS

AC OUTPUT
AC outlet is activated

HVDC OUTPUT
HVDC (high voltage DC) is activated.

USB-C OUTPUT
60W USB-C output is activated.

ADJUSTABLE DC OUTPUT
Adjustable 5V-25V DC output is activated.

LOW TEMPERATURE PROTECTION
Battery’s temperature is too low, the charging circuit is shut off.

LOW POWER PROTECTION (ONLY DURING PASS-THROUGH)
Occurs when outgoing power is higher than incoming power and battery is empty. Omnicharge will cut off the outgoing power until a sufficient battery level has been reached

OVERPOWER PROTECTION
Device is drawing too much power. Omnicharge will limit or cut off the output power.

OVERHEATING PROTECTION
Battery temperature is too high. Omnicharge will limit or cut off its input and output power.

OVERVOLTAGE PROTECTION
Barrel input voltage exceeds the 36V limit. Input charging circuit is shut off.

USB OUTPUT
USB ports are turned on

CHARGING INPUT
Your Omnicharge is being charged.

OPTIMAL CHARGING
Charging at maximum power

SOLAR CHARGING
Charging from solar power

Wireless Charging
Wireless charging is activate

DC OUT
Turn on DC output and set the voltage and amperage.
WALL SOCKET
Choose whether the AC outlet will output 120V AC or 150V HVDC
USB Choose whether your USB-A ports are on or off when you turn on your Omnicharge. The default setting is on.
SCREEN OFF TIMER Set the screen auto shut-off time here. The default setting is 5 min

Product installation

AUTO SHUT DOWN
Set the power auto shut-off time here. The default setting is 5 min
TEMPERATURE
Choose whether your temperature is displayed in celcius or fahrenheit
BUTTON LIGHT
Choose whether the button lights are on or off. The default setting is on.
ABOUT
Find the model name, capacity, firmware version, and serial number information here.

AC OUTLET

Max output power: 100W

To change the AC output mode, double press the Power Button to enter the menu and select Wall Socket.

Choose 120V AC/150V HVDC mode in the menu.
Note:
Only choose 150V HVDC if you are using a switch mode power supply, such as a laptop’s AC power adapter. Check our support page at www.omnicharge.co for more detailed information.
When AC/HVDC is active, the following icons should appear on the screen

120V AC output
150V HVDC output

DC OUTPUT

5V – 25V with 0.1V Accuracy, up to 5A (100W max)

The DC output feature can directly charge your laptop without needing your laptop charger.

Warning: Before using DC Output make sure you know the correct voltage for your laptop. Using the wrong voltage can damage your device.

Note: For more information visit our support page at www.omnicharge.co/support
Set voltage and amperage through the menu
Product Installation
Omnicharge keeps 4 voltage presets. You can press and hold the power button while selecting a preset to customize the voltage and amperage.

Once active, the DC icon will appear.
Adjustable DC output

Power your device through the DC port.

DC to Surface Cable
DC to MagSafe 2 Cable

You can purchase DC cables from our website. For more information about available accessories, please visit www.omnicharge.co/products

USB-C PORT

USB-C port max output: 60W The USB-C port is plug-and-play. Plug your USB-C device into the USB-C port to start charging

Note: If your USB-C output does not start charging, try to reconnect the USB-C cable

Power any USB-C device.

RECHARGING FROMTHE USB-C PORT

USB-C port max input: 30W
Fully recharge in 3 hours

Plug in a USB-C wall charger and it will start recharging the Omni 20+

Note: If the Omnicharge does not detect incoming power, try to plug in your USB-C charger while the Omnicharge is turned off. Once charging has started, you can power on the Omnicharge to utilize pass-through charging.

Product Installation

RECHARGING FROM THE BARREL PORT

DC Input 5V-25V, Up to 3A (2W – 30W)

Charging your Omnicharge
Charge the Omnicharge with the Power Station, or use an AC adapter with a 5.5 x 2.1mm barrel plug.
Note : Make sure the output voltage of your adapter falls within 5V -25V range.