BRESSER BR-180RGB COB LED Studio Light Instruction Manual
- May 15, 2024
- BRESSER
Table of Contents
BR-180RGB
COB LED Studio Light
Art. No. F005100/F005107
INSTRUCTION MANUAL
BR-180RGB COB LED Studio Light
Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.
https://www.bresser.de/PF005100
WARRANTY
http://www.bresser.de/warranty_terms
GENERAL WARNINGS
DANGER OF BODILY INJURY!
Do not use in the presence of children or animals. Store out of reach of
children and animals.
RISK OF MATERIAL DAMAGE!
Make sure that no one can trip over connection cables of the device. The
device could be knocked over.
Only use the recommended power cable or the recommended battery for the power
supply!
The manufacturer accepts no liability for voltage damage caused by the use of
an unsuitable power supply!
DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source
(power adapter). Only use the device as described in the manual. Otherwise,
you run the
DANGER of an ELECTRIC SHOCK.
Never bend, squeeze or pull power cables, connecting cables, extensions or
connectors. Protect cables from sharp edges and heat.
Check this device, cables and connections for damage before use.
Never attempt to operate a damaged device, or a device with damaged electrical
parts!
Damaged parts must be replaced immediately by an authorized service agent.
Operate the device only in a completely dry environment and do not touch the
device with wet or damp body parts.
RISK OF GLARE!
Make sure that people and animals do not look into the light. The high
luminosity can cause glare to the eyes and afterimages. This impairment of
vision can lead to accidents.
FIRE/EXPLOSION HAZARD!
Always place the device in such a way that it cannot tip over and ensure that
it is stored in a reasonably safe place.
- Keep children and animals away from the device! They could knock the device over.
- Make sure that no one can trip over connection cables. The device could be knocked over.
- Do not expose the device to high temperatures. Do not short-circuit the device or dispose of in fire! Excessive heat and improper handling can cause short circuits, fires and even explosions!
- Only use the recommended power supply*!
IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your
dealer.
They will contact the Service Center and can arrange the return of this device
for repair if necessary.
Disconnect the power supply by pulling the mains plug when the appliance is
not in use, in case of a longer interruption of operation and before any
maintenance and cleaning work.
Place your device so that it can be disconnected from the power supply at any
time. The power outlet should always be near your appliance and should be
easily accessible, as the plug of the power cord serves as a disconnect device
from the mains supply. To disconnect the unit from the mains, always pull the
mains plug and never pull the cable!
Do not subject the device to excessive vibrations.
PARTS OVERVIEW
PARTS DESCRIPTION
1. LED-Screen
2. Temperature check / Bluetooth Reset
3. Fan | Channel Select
4. CCT / HSI / FX Mode Select
5. Power Switch
6. Power Switch
7. Adjustment Knob
8. Power Socket
9. DMX Input | Output (RJ45)
10. Umbrella Socket| 11. Fixing Screw for Umbrella Socket
12. Tilt Adjusting Screw
13. U-holder
14. Fixing Screw for 16mm (5/8″) Spigot
15. Spigot connection hole
16. Handle
17. Release knob for S-Bajonet
18. COB LED Light Source
19. S-Bajonet holes
20. Ventilation Slots
---|---
FUNCTIONS & OPERATION
Temperature check / Bluetooth Reset
Shortly press ② to check the working temperature. Long press ② to reset the
bluetooth connection.
Cooling fan / Channel Selection
Shortly presst ③ to switch on or off the coo ling fan.
Note: When the cooling fan is switched off, the indensity is allowed to
dimmer max to 30%.
Long press ③ to allow the access to 2.4G remote control, wheel the knob ⑦ to
select the address 01 -99.
CCT / HSI / FX Control Mode
Shortly press ④ to switch between CCT and HSI control.
-
In the CCT mode, shortly press the knob ⑦ to switch to control between dimmer and color temperature and turn the knob ⑦ to change the color temperature from 2700K to 6500K or change intensity from 0 % to 100 %.
-
In the CCT mode, long press the knob ⑦ to allow access to FX control mode. Shortly press the knob ⑦ to switch control of special effects x12, flash speed from 1 to 9, and dimmer from 0 % to 100 %.
Wheel the knob ⑦ to change the number.
Long press ④ to exit from the FX control. -
In the HSI mode, shortly press the knob ⑦ to switch the change the hue 0-360°, saturation 0-100% and intensity 0-100%. Turn the knob ⑦ to change the number.
-
In the HSI mode, long press the button ④ to enter FX control mode. Shortly press the knob ⑦ to switch control of special effects x8, flash speed from 1 to 9, and dimmer from 0 % to 100 %. Turn the knob ⑦ to change the number. Long press ④ to exit from the FX control.
FX Control ( special effects)
Welding / Pulsing / Campfifire / Lightning / Explosion / TV / Candle / Fault
Bulb / Breathe / Paparazzi / SOS / Flame / Fade / Cop Car / Party / Fireworks
/ Disco / Ambulance / Fire Siren / RGB Loop
APP CONTROL
This studio light can be controlled throug a smart device (e.g. Tablet-PC, Smartphone) by the ‘LinkLite’ App.
- Use the link or QR code below to download the App ‘LinkLite’.
- Turn on the studio light and wait about 5 seconds.
- Long press ② to reset the bluetooth connection for the studio light.
- Enable Bluetooth on your smart device and connect with the studio light model ‘BR180RGB’.
Once the studio light is connected, you are able to control the device through
the App.
Note: If the connection failed, add the studio light ‘BR-180RGB’ manually
through the App (select ‘Add device’).
APP DOWNLOAD:
https://a.smart321.com/comlinklite
ADJUSTING THE TILT ANGLE
- Hold the LED light and slowly loosen the locking screw (11) for the tilt joint.
- Move the light head to the desired position and tighten the locking screw (11) again hand-tight.
*MOUNTING ON A TRIPOD (optional)**
- Loosen the fixing screw (14) for the Spigot connection hole (15) so that the opening of the Spigot connection is exposed.
- Place the LED light with the opening on the Spigot of a tripod and tighten the fixing screw (14) firmly.
*ATTACHING ACCESSORIES (optional)**
- This LED light is equipped with umbrella socket (10) which can be used to attach optional accessories with a suitable rod (e.g. umbrella). Just put the accessory’s rod into the umbrella socket hole (10) and fix it by turning the fixing screw (11)
- This LED light is also has a S-bayonet connection holes (19) which can be used to attach optional accessories with suitable S-bayonet.
*not included
DISPOSAL
Dispose of the packaging materials properly, according to their type, such as
paper or cardboard. Contact your local waste-disposal service or environmental
authority for information on the proper disposal.
**** Do not dispose of electronic devices in the household garbage! As per
the Directive 2012/19/EC of the European Parliament on waste electrical and
electronic equipment and its adaptation into German law, used electronic
devices must be collected separately and recycled in an environmentally
friendly manner.
CE DECLARATION OF CONFORMITY
Bresser GmbH has issued a „Declaration of Conformity“ in accordance with
applicable guidelines and corresponding standards. The full text of the CE
declaration of conformity is available at the following internet address:
www.bresser.de/download/BRS-
COB/CE/BRSCOB_CE.pdf
WARRANTY & SERVICE
The regular warranty period is 2 years and begins on the day of purchase. To
benefit from an extended voluntary warranty period as stated on the gift box,
registration on our website is required.
You can consult the full warranty terms as well as information on extending
the warranty period and details of our services at
www.bresser.de/warranty_terms.
*not included
TECHNICAL DATA
| Model No. | BR-180RGB |
|---|---|
| Art. No. | F005100 / F005107** |
| Power Consumption | 180W |
| Color Temperature | 2700K-6500K ±200K |
| CRI | ≥ 97 |
| Dimmer | 0%-100% |
| Saturation | 0%-100% |
| Channels | up to 99 channels in parallel operation |
| LED Type | High power COB (Chip on Board) LED |
| Special Effects | 20 |
| Flash Speeds | 1-9 |
| App Control | via LinkLite App (free of charge via download link) |
| Remote Control | via 2.4G wireless remote control* |
| Remote Control Distance | up to 30m |
| DMX512 dimmer | yes, via RJ45 interface connection |
| DC power input | 100-240V~50/60Hz |
| Dimensions | 140140300mm |
*not included / *2 pcs. kit of F005100
not included
Service
Please contact the service centre first for any questions regarding the
product or claims, preferably by e-mail.
E-Mail: service@bresseruk.com
Telephone: +44 1342 837 098
BRESSER UK Ltd.
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain
Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.
Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
@BresserEurope
| Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
Great Britain
---|---
Errors and technical changes reserved.
Manual_F005100_F005107_BR-180RGB_en-nl-de_BRESSER_v022024a
Documents / Resources
|
BRESSER BR-180RGB COB LED Studio
Light
[pdf] Instruction Manual
F005100, F005107, BR-180RGB COB LED Studio Light, BR-180RGB, COB LED Studio
Light, LED Studio Light, Studio Light, Light
---|---
|
BRESSER BR-180RGB COB LED Studio
Light
[pdf] Instruction Manual
BR-180RGB COB LED Studio Light, BR-180RGB, COB LED Studio Light, LED Studio
Light, Studio Light, Light
References
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- Bresser | Startseite | Expand Your Horizon mit BRESSER
- Bresser | BRESSER BR-180RGB COB LED Light | Expand Your Horizon
- Linklite
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>