WalkFit Smart Watch User Manual

: June 7, 2024
: WalkFit

WalkFit Smart Watch User Manual

Introduction

Thank you for purchasing our products. This manual addresses the safety guidelines, warranty, and operating instructions. Please review this manual thoroughly before operating your device.

All pictures in this manual are for illustration purpose only. Actual product may vary due to product firmware upgrade and app upgrade.

Getting Started

What’s in the Box

Smart watch (ID205L with bands)
Charging cable
Quick Start Guide

What’s in this Document

This manual gets you started quickly with setting up your watch. Setup ensures that your watch can synchronize its data with the Letsfit app, where you can get detailed information on your stats, view historical trends, log sleep, and more. As soon as setup is complete, you’re ready to start moving. The remainder of the manual walks you through every function on your ID205L.

Setting up Your Watch

Charging Your Watch

Please fully charge your watch before initial use.

Insert the USB plug of the charging cable into the USB port on your computer or a UL-certified USB wall charger.
Hold the other end of the charging cable near the port on the back of the watch until it attaches magnetically.
Make sure the pins on the charging cable lock securely with the port. The connection is secure when the watch vibrates and the battery icon with percent charged appears on the screen.

When the watch shows that the battery is low, connect the watch to a USB port with 5V-500mA.

While the watch charges, there is a battery progress bar on the screen and you can press the function button to check the battery level.

Remove the watch from the power supply once fully charged.

USB charger requirement: CD USB port (5V-500mA).
Charging time: 2-3 hours.

Disassembling / Assembling Your Watch

Disassembly

To remove the wristbands, turn over the watch and find the quick-release lever.
While pressing the quick-release lever inward, gently pull the wristband away from the watch.
Repeat on the other side.

Assembly

To reattach the wristbands, slide the pin (the side opposite the quick-release lever) into the notch on the watch. Attach the wristband with the clasp to the top of the watch.
While pressing the quick-release lever inward, slide the other end of the wristband into place.
When both ends of the pin are inserted, release the quick-release lever.

Wearing Your Watch

All-day Wear and Exercise
For all-day wear when you’re not exercising, wear the device on your wrist horizontally, a finger’s width below your wrist bone and lying flat, the same way you would put on a watch.
Wearing Your Watch

for optimized heart rate tracking, keep these tips in mind.

Experiment with wearing the watch higher on your wrist during exercise. Because the blood flow in your arm increases the farther up you go, moving the watch up a couple of inches can improve the heart rate signal. Also, many exercises such as bike riding or weight lifting require you to bend your wrist frequently, which is more likely to interfere with the heart rate signal if the watch is lower on your wrist.
Do not wear your watch too tight. A tight band restricts blood flow, potentially affecting the heart rate signal. This being said, the watch should also be slightly tighter (snug but not constricting) during exercise than during all-day wear.

Using Your Watch

App Installation

Use the watch with our customized Letsfit app. You can download Letsfit from App Store / Google Play or scan the QR codes below to download.

IOS

LETSFIT
ANDROIND

Note : Lets fit app is only compatible with smartphones, not tablets or PCs.

Smart Phone System Requirements

iOS 11.0 & higher
Android 6.0 & higher
Bluetooth 4.0 & higher

Account Registration and Login

Please register an account with a valid email address. After registration, check your email box to complete email verification, and then tap “Verified” to log in.

**Pairing the Watch with Your Phone

**

Please pair the watch with your phone in the Letsfit app, NOT in the Bluetooth settings of your phone.

Pair the watch with your smartphone in the Letsfit app.
IOS

Android
Do NOT pair the watch with your smartphone in your phone’s Bluetooth settings.

Enable the Bluetooth of your smartphone.
Open the Letsfit app on your smartphone and go to the “Settings” page, tap “+ Pair new device”.
Tap “ID205L” , and your smartphone starts searching devices.
In the list of found devices that appear on your smartphone, tap “ID205L” to connect the watch to your smartphone. (If your phone failed to find ID205L, please search the watch on your smartphone again.)

Notes :

Once the watch is connected to your app, the watch will automatically search and reconnect itself if the connection is lost or when Bluetooth is restarted after manual disconnection.
If you unpair the watch with the app, the watch will be reset, and the information on the watch will be cleared. Please do not unpair the watch with the app unless there is an issue that will require a reset.
The watch can only pair with one smartphone at a time. When pairing, please ensure that the watch screen is on and the watch and your smartphone is within 0.5 meters distance.

App Interfaces

Activity
Daily Active Hours
Daily Steps
Training
When you start a sport mode on your watch, detailed data and graphs will be displayed here after the exercise is over (swipe down to sync data first).
Settings
Tap “ID205L” , you can customize call / message / alarm alert or set other parameters.

Getting to Know Your Watch

**Function Button

**

Function Button

Press the function button to wake the screen or return to the previous interface.
Press and hold the function button to turn on the watch.

Watch Interfaces

This is a touch screen; swipe the screen to go to different interfaces, and tap to enter the function. this home screen is a clock.. on the clock :

Swipe down to see notifications.
swipe up to see notifications.
swipe left to see the function list.
swipe right to seen the status bar. (automatic haert rate monitoring, wrist sense, do not disturb, find my phone.
fig 1

After the watch is bound to the app, the home screen will display the time and date as shown in fig. 1.

You can customize the home screen by following the steps below:

Tap and hold the home screen.
Swipe down to choose one and tap to confirm.

Wake a Dimmed Screen
To conserve power, the watch has a standby mode in which the screen turns off. To wake the screen, turn your wrist towards you or press the function button.

Function Introduction

Tracks your exercise data in up to 8 sports modes.
Tracks your real-time heart rate automatically and continuously.
Guides your breathing for a relaxation.
Set alarms in the app to have the watch vibrates to wake you up, take pills, and more.
Control the music playing of your smartphone.
Timing and countdown.
Some basic settings of the watch.
Your recent sports record.

Tracking Sports

The watch tracks your exercise data in up to 8 sports modes.

Start a sport

Tap sport swipe the screen to view sports modes
Tap the sport you choose to start.

During sports

Swipe the screen left / right to flip through exercise data and control the music playing on your phone.
Press the function button to pause / resume the sport.

End the sport

press and hold the function button to end the sport tap to confirm.
Exercise data is displayed after the exercise has ended. swipe up the screen to flip through exercise data:

Notes :

After ending an exercise, you can view detailed data and graphs in the app (Go to the “Training” page, swipe down the page to synchronize data, and tap the exercise you just ended).
Data of exercises less than 1 minute will not be saved.
When the battery level is less than 20%, you cannot start a sports mode. Please charge the watch to operate it again.

**Monitoring Heart Rate

**

The watch tracks your real-time heart rate automatically and continuously. You can also view your detailed heart rate data on the watch screen or in the app.

Note:
To monitor heart rate more accurately, wear the watch on the upper position of your wrist and a bit tighter than usual when you exercise. In addition, complete your profile in the app.

**Relaxing

**

Tap to start the relaxing press the the function button to end the relaxing tap to confirm.

Relaxing Function

Setting Alarms

Go to the “Settings” page in the Letsfit app and tap “ID205L”.
Tap “Alarm” to enter the alarm setting interface.
Tap “Add” to add an alarm.
Set the alarm time.
Tap “Confirm” to save your settings.

You can enable/disable the alarm on your watch (Tap “Alarm” on the watch and then turn on/off the alarm you set.)

Controlling Phone Music

After the watch is connected to your phone, tap “Music Controller” on the watch to enter the function and control the music playing on your phone.
Controlling Phone Music

Note:
You can only control the music player that’s running on your phone.

Tracking Sleep

The watch automatically tracks your sleep duration (Deep Sleep, Light Sleep, and Wake-sleep) and consistency with a comprehensive analysis of sleep quality data so you can see your sleep trends and improve your routine. You can check your detailed sleep data in the app.

More Functions

**Call Notification

**

When there is an incoming call, the watch vibrates to alert you, and the screen displays the caller ID. Tap “ ” on the watch screen to reject the call.

Notes:

Only when “Notification alerts” is enabled in the app ( “Settings” page ID205L Notification alert turn on notation alerts will calls be notified.
When the “Do not disturb” function is enabled on the watch status bar calls will not be notified on the wateh during the do not disturb period.

Message Notification

When messages (like short messages, Facebook, Twitter, and Instagram messages) come in, the watch vibrates to alert you, and the screen displays the message content.

Notes:

Only when “Notification alerts” is enabled in the app (“Settings” page ID205L Notification alert turn on notation alerts will calls be notified.
When the “Do not disturb” function is enabled on the watch (status bar calls will not be notified on the wateh during the do not disturb period.

Sedentary Reminder

The watch vibrates to remind you to get up and move around when you have been sitting too long (activity page active hours sedentary alert settings enable the movement reminders function and set the remind period.

Find My Phone

You can use the watch to locate your phone by making your phone vibrate or ring when the distance between our phone and the watch is within 10 meters (33 feet).

go to the settings page ID205L find my phone in the app and enable the function.
Swipe the watch screen right to come to the status bar and tap to use the function.

Note:
You can use the find phone function only when it is enabled in the app.

Basic Specifications

model no: ID205L
sync: Bluetooth 4.2
screen: 1.3 TFT LCD
battery capacity: 210mAh
working voltage: 3.8V
working temperature: -10 C to 40 C
weight: 1.37oz (39g)
water proof rating: IP68
working time: about 10 days

FAQs

Failure to re-pair the watch with the Letsfit app on your smartphone

Make sure your smartphone’s Bluetooth is enabled and your smartphone’s system meets the requirements of Android 6.0 or higher, iOS 11.0 or higher, and Bluetooth 4.0 or higher.
Make sure the distance between your smartphone and the watch does not exceed 0.5 meters and that Bluetooth communication is also within range (10 meters max).
Make sure your watch has enough battery life. If there is still a problem after being fully charged, please contact us.

Occasional failure to connect with Bluetooth
Reboot your smartphone or restart your smartphone’s Bluetooth

Failure to receive SMS / calls notifications

Calls / SMS notification function works when the watch connects to your smartphone via the app. Please kindly refer to the following tips:

Go to your smartphone Settings, find Letsfit app, and enable the Location and all Notifications.
Enable your phone’s Bluetooth and go to the Letsfit app to pair the watch
open the app. go to the settings page ID205L “Notification alerts”, turn on “Notification alerts”.
Make sure the “Do not disturb” function is not enabled on the watch

The watch is disconnected from the Letsfit app on your smartphone

The watch will disconnect from your smartphone in the following cases:

Smartphone Bluetooth is off or exceeds the Bluetooth
connection range (the maximum Bluetooth connection range is 10 meters and can easily be reduced by walls, furniture, etc.)
The Letsfit app is closed on the phone. (This can occur automatically under certain circumstances.)

To reconnect the watch to your smartphone, please kindly take the following steps:

Go to your smartphone system Settings, find the Letsfit app, and enable the Location and Bluetooth.
Clear all running / background processes on your smartphone.
Open the Letsfit app, go to the “Settings” page, tap “ID205L”, and then the watch will reconnect to your smartphone and update data. You can also restart your smartphone and Bluetooth, then re-pair the watch in the app.

Important Safety Instructions

The device contains electrical equipment that may cause injury if not used properly. For example, prolonged contact may contribute to skin allergies for some users. To reduce irritation, please read the safety guidelines on the following pages to ensure proper use and care.

Do not expose your device to [[quid, moisture, humidity or rain while charging; do not charge your device when it is wet, as this may result in electrica[ shock and injury.
Keep your device clean and dry. Do not use abrasive cleaners to clean your device.
Consult your doctor before use if you have any preexisting conditions that might be affected by using this device.
Do not wear it too tight. If your device feels hot or warni, or if it causes any skin irritation or other discomforts, please discontinue using your device and consult your doctor.
Do not expose your watch to extremely high or low temperatures.
Do not leave your watch near open flames such as cooking stoves, candles, or fireplaces
This product is NOT a toy — never allow children or pets to play with this product. Always store the product out of the reach of children.
The devices themselves or the many small parts they contain may cause choking if ingested.
Do not use your device in a sauna steam room.
Dispose of this. device, The device’s battery and its package in accordance with local regulations.
Do not check any notifications, CPS, or any information on your device’s display while driving or in other situations where distractions could cause [njury or hazard. Always be aware of your surroundings while exercising.

Battery Warnings

A lithium-on battery is used in this device If these guidelines are not followed: bafteries may experience a shortened life span or may cause fire, chemical bum electrolyte leakage, andior inpury.

Do not disassemble, modify, rernanufacture, puncture or damage the device or batteries
Do not remove or attempi to remove the non-user-replaceable battery
Do not expose the device or batteries to fire, explosion, or other hazards

Health Warnings

If you have a pacerrtaker or other in eleMonic device, consult your physician before using a heart rate monitor
The optical wrist rieari rate monitor emits green light and slashes occasionally_ Consult your physician if you have epilepsy or are sensitive to fias’hing lights.
Always can your physician before begirimng or modifying any exercise program
The device, accessories, heart rate monitor and related data are intended to be used only for general fitness and wellness purposes, not for medical purposes, and are not intended to diagnose_ monitor, &eat, cure, or prevent any disease or condition
The heart rate readings are for reference only, and no responsibility is assumed for the consequences of any false readings.
While the optical wrist heart rate monitor technology typically provides the best estimate of a user’s heart rate, there are inherent limitations with the technology that may cause some of the heart rate readings to be inaccurate under certain circumstances, including the user’s physical characteristics, fit of the device, and type and intensity of activity.
The smart watch relies on sensors that track your movements and other metrics. The data and information provided by these devices are intended to be a close estimation of your activity and metrics tracked, but may not be completely accurate, including step, sleep, distance, heart rate, and calorie data.
If you have eczema, allergies or asthma, you may be more likely to experience skin irritation or allergies from a wearable device.
Whether you have the conditions above or not, if you start to experience any discomfort or skin irritation on your wrist, remove your device. If symptoms persist longer than 2-3 days of not using your device, contact your doctor.
If you sweat for more than two hours while wearing your watch, be sure to clean and dry your band and your wrist to avoid skin irritation.
Prolonged rubbing and pressure may irritate the skin, so give your wrist a break by removing the band for an hour after extended wear.

Maintenance

Regularly clean your wrist and the smart watch, especially after sweating during exercise or being exposed to substances such as soap or detergent which may adhere to the internal side of the watch.
Do not wash the watch with household cleanser. Please use soapless detergent, rinse thoroughly and wipe with a soft towel or napkin.
While the watch is water resistant, wearing a wet band is not good for your skin
If your bands get wet-for example after sweating or showering-clean and dry them thoroghly before putting them back on your wrist.
Be sure your skin is dry before you put your bands back on.
Do not bring your device into contact with any sharp objects, as this could cause scratches and other damage.
For light-colored arm bands, minimize direct contact with dark colored clothing, as color transfer can occur.

Warranty

We strive to build our products with the highest attention to detail and craftsmanship. However, sometimes there are occurrences of a defect, so we are happy to offer a ONE-year hassle-free warranty on all our devices as we continue to make amazing products. Please contact us if you have any questions about our devices.