omnicharge Omni 20+ Smart and Portable Power Bank User Manual
- June 6, 2024
- omnicharge
Table of Contents
omnicharge Omni 20+ Smart and Portable Power Bank User Manual
BEFORE USING
Calibrate the battery
To make sure the battery percentage reading is correct, make sure to calibrate the battery whithin the first seven days of receiving the product.
It’s easy to do. Follow these steps:
-
Fully discharge Omnicharge until the screen turns off. Press the Power Button and you should see an empty battery icon on the screen.
-
Fully charge your Omnicharge to 100% to finish the calibration.
Note: The Omnicharge battery needs to be recharged at least every 6 months to avoid over depletion. Failure to do so can cause the battery to malfunction and is not covered by warranty.
PORTS AND BUTTONS
Note: For optimal wireless charging, place phone horizontally towards the back of the Omnicharge.
- AC Outlet
- Power and Menu Button
- USB Button
- AC Outlet Button
- Quick Charge USB (QC 3.0 Compatible)
- 5V/3A USB-A Port
- DC Input/Output (5.5 x 2.1mm Barrel Port)
- USB-C Input/Output
- Wireless Charging
BUTTON FUNCTIONS
PRIMARY CONTROLS
Long press to power on
Long press to power off
On/Off AC Outlet
On/Off USB Ports
MENU CONTROLS
Double press to enter the menu
Quick press to select
Move Up
Move Down
SCREEN
OLED screen with real time metrics
- Status Icons
- Power Input (watts)
- Battery Power Output (watts)
- Battery Temperature
- DC Output Voltage
- Battery Percentage
Note: When you are pass-through charging, the battery output field will show a lower value and can even show 0W output, since the output field is showing how much power is output from the battery and not how much is output from the port.
SCREEN ICONS
-
AC OUTPUT
AC outlet is activated. -
HVDC OUTPUT
HVDC (high voltage DC) is activated -
USB-C OUTPUT
60W USB-C output is activated. -
ADJUSTABLE DC OUTPUT
Adjustable 5V-25V DC output is activated. -
LOW TEMPERATURE PROTECTION
Battery’s temperature is too low, the charging circuit is shut off. -
LOW POWER PROTECTION (ONLY DURING PASS-HROUGH)
Occurs when outgoing power is higher than incoming power and battery is empty. Omnicharge will cut off the outgoing power until a sufficient battery level has been reached. -
OVERPOWER PROTECTION
Device is drawing too much power. Omnicharge will limit or cut off the output power. -
OVERHEATING PROTECTION
Battery temperature is too high. Omnicharge will limit or cut off its input and output power. -
OVERVOLTAGE PROTECTION
Barrel input voltage exceeds the 36V limit. Input charging circuit is shut off. -
USB OUTPUT
USB ports are turned on. -
CHARGING INPUT
Your Omnicharge is being charged. -
OPTIMAL CHARGING
Charging at maximum power. -
SOLAR CHARGING
Charging from solar power -
Wireless Charging
Wireless charging is active.
MENU NAVIGATION
-
DC OUT
Turn on DC output and set the voltage and amperage. -
WALL SOCKET
Choose whether the AC outlet will output 120V AC or 150V HVDC -
USB
Choose whether your USB-A ports are on or off when you turn on your Omnicharge. The default setting is on. -
SCREEN OFF TIMER
Set the screen auto shut-off time here. The default setting is 5 min.
-
AUTO SHUT DOWN
Set the power auto shut-off time here. The default setting is 5 min. -
TEMPERATURE
Choose whether your temperature is displayed in celcius or fahrenheit -
BUTTON LIGHT
Choose whether the button lights are on or off. The default setting is on. -
TIME REMAINING
Choose whether the time remaining is displayed
-
LANGUAGE
Choose the screen language -
FACTORY RESET
Reset the Omnicharge to the factory settings -
ABOUT
Find the model name, capacity, firmware version, and serial number information here.
AC OUTLET
Max output power: 100W
To change the AC output mode, double press the Power Button to enter the menu and select Wall Socket.
- Choose 120V AC/150V HVDC mode in the menu
Note:
Only choose 150V HVDC if you are using a switch mode power supply, such as a
laptop’s AC power adapter. Check our support page at
www.omnicharge.co for more detailed information.
-
When AC/HVDC is active, the following icons should appear on the screen
AC output
HVDC output
-
Power any device.
DC OUTPUT
5V – 25V with 0.1V Accuracy, up to 5A (100W max)
The DC output feature can directly charge your laptop without needing your laptop charger.
Warning: Before using DC Output make sure you know the correct voltage for your laptop. Using the wrong voltage can damage your device.
Note: For more information visit our support page at www.omnicharge.co/support
Set voltage and amperage through the menu
Omnicharge keeps 4 voltage presets. You can press and hold the power button
while selecting a preset to customize the voltage and amperage.
Once active, the DC icon will appear.
Adjustable DC output
Power your device through the DC port.
DC to Surface Cable
DC to MagSafe 2 Cable
You can purchase additional DC cables from our website. For more information
about available accessories, please visit
www.omnicharge.co/products
USB-C PORT
USB-C port max output: 60W
The USB-C port is plug-and-play. Plug your USB-C device into the USB-C port to start charging
Note: If your USB-C output does not start charging, try to reconnect the USB-C cable.
Power any USB-C device.
RECHARGING FROM THE USB-C PORT
USB-C port max input: 45W
Fully recharge in 3 hours
Plug in a USB-C wall charger and it will start recharging the Omni 20+.
Note: If the Omnicharge does not detect incoming power, try to plug in your USB-C charger while the Omnicharge is turned off. Once charging has started, you can power on the Omnicharge to utilize pass-through charging.
USB-A PORTS
5V⎓3A, 9V⎓2A, 12V⎓1.5A QC3.0 compatible
Choose whether the USB output is on or off by default.
RECHARGING FROM THE BARREL PORT
DC Input 5V – 25V, Up to 3A (2W – 45W)
Charging your Omnicharge
Use any AC wall charger, or other power adapters like your laptop charger to
recharge your Omnicharge.
Note: Make sure the output voltage of your adapter falls within 5V – 25V range. The Omni 20+ only accepts 5.5 x 2.1mm barrel plugs.
WIRELESS CHARGING
Qi wireless charging 10W Output
Simply place your phone on top of the Omnicharge to get fast and reliable wireless charging.
For optimal wireless charging, align your phone horizontally with the back
edge of the Omnicharge as shown in the picture.
You will see a flashing wireless icon when the phone has been detected.
Wireless Charging
Wireless charging is activated anytime USB-A charging is ON. Remember to press the USB-A button to activate. To set USB-A to be turned on by default.
Note: The range of the optimal charging area varies depending on the size of the receiver coil of your phone. Some phone models have small receiver coils and can experience sudden interruptions after few seconds of charging. This is because of minor alignment deviations between the transmitter and receiver coil. Please fine-tune your phone’s position until it gets stable wireless charging.
TECHNICAL SPECIFICATION
-
GENERAL
Weight: 1.35 lbs (611 g)
Dimension: 5.0″x 4.8″x 1.1″(12.7 x 12.2 x 2.7 cm) -
USB-C
Bidirectional Input/output charging
Input: USB-PD, 5V~20V, up to 3A, 45W max
Output: 5V⎓3A，9V⎓3A，12V⎓3A，15V⎓3A，20V⎓3A, up to 3A, 60W max -
USB-A Output
Port1: QC 3.0，5V⎓3A，9V⎓2A，12V⎓1.5A
Port2: QC 3.0，5V⎓3A，9V⎓2A，12V⎓1.5A -
DC Port
Bidirectional Input/output charging
Input: 5~25V, up to 3A, 45W max
Output: 5~25V, up to 5A, 100W max -
AC PORT
120V AC, 60Hz, 100W max US version
230V AC, 50Hz, 100W max EU version -
WIRELESS CHARGING
Output: 10W -
CAPACITY
6 cells, 70Wh max at 3.7V -
OPERATING ENVIRONMENT
Temperature 0°C-40°C
Humidity 30-70%
Altitude ≤2000m
CUSTOMER SUPPORT
All Omnicharge products have gone through quality inspection. If you find your Omnicharge or any Omnicharge accessory is experiencing or demonstrating any abnormal behavior, immediately stop all product use and contact us at support@omnicharge.co.
FOLLOW US
https://www.facebook.com/omnicharge
https://www.instagram.com/omnicharge
https://www.youtube.com/c/omnicharge
https://twitter.com/omni_charge
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>