TSI 300W AC DC Power Supply Plus Heater User Guide
- June 7, 2024
- tsi
Table of Contents
300W AC DC Power Supply Plus Heater
INSTALLING THE 300W AC/DC POWER SUPPLY PLUS HEATER
INTO ENVIRONMENTAL ENCLOSURE
INSTALLATION GUIDE
P/N 6012152, REVISION B JANUARY 2020
This guide will help you quickly install the 300W AC/DC Power Supply plus Enclosure Heater into the Environmental Enclosure.
Unpacking
- Unpack the power supply plus enclosure heater and verify that all the items listed in the following table are present.
- Contact TSI immediately if items are missing or broken.
Qty.
|
Item Description
|
Reference Picture
---|---|---
1
|
Power Supply, 300 watts
|
1
|
Thermostat
|
Qty.
|
Item Description
|
Reference Picture
---|---|---
2
|
Thermostat Wires
|
1
|
Heater
|
2
|
Vent Plugs
|
4
|
Nuts
|
4
|
Washers
|
TSI and TSI logo are registered trademarks of TSI Incorporated.
Warning Labels
Warns that the instrument could be hot to the touch or a burn hazard.
Installing the Power Supply and Enclosure Heater
1. Connect the power cable to the power supply.
2. Install power supply onto threaded studs.
3. Using a 7/16″ socket on a socket wrench, install the 4 nuts and washers (hand tight) to secure to the power supply to the threaded studs.
4. Connect the power cable to the DIN rail.
5. Using a small flat blade screwdriver, install the red wires onto the Thermostat.
6. Clip the Thermostat onto the DIN rail.
7. Insert the #1 wire from the left side of the Thermostat into the 1st Gray connector.
8. Clip the Heater onto the DIN rail.
9. Insert the #2 wire from the right side of the Thermostat into the left side of the heater connector.
DO NOT PLUG THE THERMOSTAT WIRES INTO THE GREEN/YELLOW PHOENIX GROUND CONTACTS THE THERMOSTAT MUST PROVIDE POWER TO THE HEATER. BYPASSING THE THERMOSTAT, OR PLUGGING THE HEATER DIRECTLY INTO THE POWER SIDE OF THE DIN RAIL, WILL CAUSE THE HEATER TO RUN CONSTANTLY AND MAY DAMAGE EQUIPMENT AND LEAD TO PREMATURE FAILURE(S).
10. Insert the heater connector into the final pair of DIN rail 24V DC power supply connectors.
11. Insert vent plugs into openings to help keep heat inside enclosure in cold environments. Twist covers counter clockwise to remove. Hand-tighten after inserting plug.
12. Remove vent plugs when weather conditions do not require use of the heater. Twist vent cover counter clockwise to remove vent plugs. Hand-tighten after removing plug.
Operating Instructions
- The heater thermoset is preset, no adjustment or setting is required. Thermostat will turn heater on automatically when the temperature inside the enclosure reaches approximately +5°C (41°F).
- The thermostat will automatically turn off the heater when the temperature in the enclosure is approximately +15°C (59°F).
Specifications
Nominal Heater Power…………….|
24 Volts DC; 100 Watts
---|---
Temp Range…..|
Will keep instruments inside enclosure above 0°C (32°F) with outside temperature down to -20°C (-4°F).
TSI Incorporated Visit our website www.tsi.com for more information.
USA UK France Germany
Tel: +1 800 680 1220 Tel: +44 149 4 459200 Tel: +33 1 41 19 21 99 Tel: +49 241
523030
India
Tel: +91 80 67877200
China
Tel: +86 10 8219 7688
Singapore Tel: +65 6595 6388
P/N 6012152 Rev. B
©2020 TSI Incorporated
Printed in U.S.A.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>