Sunmi T6900 PoS Handheld Mobile Instruction Manual
- June 7, 2024
- SUnmI
Table of Contents
Sunmi T6900 PoS Handheld Mobile
Quick start
FEATURES
-
NFC reader
Used for sensing Quick Pass Card. -
Magnetic card reader
Used for reading the information stored in the magnetic stripe of bank card. -
Front-facing camera (optional)
Supports photographing and 1D/2D code quick scanning. -
Type-C USB
Used for charging equipment and debugging by developers. Do not charge the battery in hazardous location. -
Function Key
Used for customized function. -
Power button
- Short press: wake up the screen, lock the screen.
- Long press: long press for 2-3 seconds in power off mode to switch on the device.
- Long press for 2-3 seconds in normal operation mode to select power off or reboot.
- Long press for 11 seconds when system is frozen for automatic reboot.
-
Printer
For printing sales slips in power on mode. -
Indicator lamp
Used for indicating the steps for swiping card. -
IC Card socket
Used for inserting the bank chip card. -
Two-dimensional code scanner(optional)
Used to read commodity code and mobile payment code. Attention: do not look directly into the eyes. -
Rear camera
Supports photographing and 1D/2D code quick scanning. -
Extend pins
- To connect to dock.(Need to buy dock separately)
- Do not use dock in hazardous location.
-
Slide down the metal buckle and take out the Nano SIM
-
SIM card slot (PSAM optional)
- Used for inserting the SIM Card(PSAM optional)
- Do not open and insert SIM card when an explosive atmosphere is present.
-
PSAM card slot
- Used for inserting the PSAM Card.
- Do not open and insert PSAM card when an explosive atmosphere is present
-
Micro SD card slot
Used for inserting extend SD card. -
Nano SIM card slot
Used for inserting Nano SIM card.
Printing instructions
This device supports 58mm thermal paper with the specifications of 57±0.5mm*Ø40mm.
- Please open the paper container with the uncovering handle, Please do not force open the paper container to avoid print headgear wear;
- Feed the paper correctly into the paper container in the direction as shown, and pull some paper outside the cutter;
- Close the cover of the paper container to finish printing paper feeding .
Note: If the printed paper is blank, please check whether the paper roll has been installed in the correct direction.
Do not open a paper container when an explosive atmosphere is present.
Notices: Safety Warning
- WARNING
- DO NOT CHARGE THE BATTERY IN HAZARDOUS LOCATION, including cable and cradle.
- DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT, including inserting SIM card, or changing paper roll.
- This device is an anti-explosion product with Ex ic IIA T3 level. Please use it in the according environment.
- Connect the AC plug to the AC socket corresponding to the marked input of the power adapter;
- This is a Class A product. This product may cause radio interference in living environments. In that case, the user may be required to take adequate measures against interference.
- Battery is un-removable. Please don’t change the battery by yourself.
Significant Safety Instructions
- Do not install or use the device during lightning storms to avoid the potential risks of lightning shock;
- Please turn off the power immediately if you notice abnormal odor, heat or smoke;
- The paper cutter is sharp, please do not touch!
Suggestions
- Do not use the terminal near water or moisture to prevent liquid from falling into the terminal;
- Do not use the terminal in extremely cold or hot environments, such as near flames or lit cigarettes;
- Do not drop, throw or bend the device;
- Use the terminal in a clean and dust-free environment if possible to prevent small items from falling into the terminal;
- Please do not use the terminal near medical equipment without permission.
Statements
- The Company does not assume responsibilities for the following actions:
- Damages caused by use and maintenance without complying with the conditions specified in this guide;
- The Company will not assume any responsibility for the damages or problems caused by optional items or consumables (rather than the initial products or approved products of the Company). The customer is not entitled to change or modify the product without our consent. The product’s operating system supports official system updates, but if you change the operating system into a third-party ROM system or alter the system files by system cracking, it may cause system instability and security risks and threats.
Disclaimer
As a result of product upgrading, some details in this document may not match
the product, and the actual product shall govern. The Company reserves the
right of interpretation of this document. The Company also reserves the right
to alter this specification without prior notice.
Modo di protezione: II 3G Ex ic IIB T4 Gc
RF Exposure Statement (SAR)
This device has been tested and meets EU, FCC and IC RSS-102 applicable limits
for radio frequency (RF) exposure. Please visit
www.sunmi.com.
EU regulatory conformance
Conformity CE
Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this device is in
compliance with the essential requirements and other relevant provisions of
Radio Equipment Directive 2014/53/EU. The full text of the EU Declaration of
conformity is available at the following internet address: https://develop-
er.sunmi.com/docs/read/en-US/maaeghjk480
INFORMATION ABOUT THE SOFTWARE
The description of accessories and components, including software, which allow
the radio equipment to operate as intended, can be obtained in the full text
of the EU declaration of conformity at the following internet address:
https://developer.sunmi.com/docs/read/en-US/maaeghjk480.
RESTRICTIONS OF USE
5150-5350MHz only be used by indoors.
Technical specifications
CE certification information (SAR)
- This device was tested for typical body-worn operations with the back of the handset kept 5mm away. To maintain compliance with RF exposure requirements, use accessories that maintain a 5mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with
- RF exposure requirements and should be avoided.
- If you are using a pacemaker, hearing aid, cochlear implant or other device, please use the phone according to the doctor’s advice.
PRODUCT SAFETY WARNINGS
Use responsibly. Read all instructions and safety information before use to
avoid injury.The limit operating ambient temperature of the equipment declared
by the manufacturer is -15~55°C
Battery Safety
Charge battery only at ambient temperatures ranging from 40°C.
CAUTION:
- The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to battery manufacturer’s instructions.
- Risk of explosion if the battery is replaced by an incorrect type . Dispose of used batteries according to the instructions.
- The battery charging temperature’s upper limit is 40°C.
-
Adapter safety
When charging, please place the device in an environment that has a normal room temperature and good ventilation. It is recommended to charge the device in an environment with a temperature that ranges from 0°C~40°C. For altitude 2km below use only -
Wi-Fi Safety
Turn Wi-Fi off in areas where Wi-Fi use is prohibited or when it may cause interference or danger, such as in airplanes while flying. Technical features and characteristic
ISED Canada compliance statements
This device complies with ISED Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
Manufacture
Shanghai Sunmi Technology Co., Ltd. Room 505, KIC Plaza, No.388 Song Hu Road,
Yang Pu District, Shanghai, China
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution : The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Declaration of Conformity
EU Representative : SUNMI France SAS 186,avenue Thiers,69006 Lyon,France
This symbol means that it is forbidden to dispose the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contact your local authority representative for detailed information on WEEE recycling.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>