V I V O STAND-V001D Single Monitor Desk Stand Instruction Manual

: June 13, 2024
: V I V O

Table of Contents

V I V O STAND-V001D Single Monitor Desk Stand
Product Information
Package Contents
Warnings
Product Usage Instructions
TIPOVER WARNING
PACKAGE CONTENTS
TOOLS NEEDED
ASSEMBLY STEPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

V I V O STAND-V001D Single Monitor Desk Stand

Product Information

The Single Monitor Desk Stand (SKU: STAND-V001D) is a versatile and sturdy stand designed to securely hold a monitor on your desk. It is compatible with both flat back and curved back monitors, providing flexibility in usage. The stand has a weight capacity of22lbs (9.98kg) and is built to ensure safety and stability.

Package Contents

(x1) Column (A)
(x1) VESA Plate (B)
(x1) Base (C)
(x4) Rubber Pad (D)
(x1) Knob (S-A)
(x1) Metal Washer (S-B)
(x3) M6x10mm Screw (S-C)
(x1) Plastic Washer (S-E)
(x4) M4x8mm Screw (M-A)
(x4) M4x12mm Screw (M-B)
(x4) M4x30mm Screw (M-C)
(x4) Spacer (M-D)
(x1) 4mm Allen Wrench (T-A)
(x1) 5mm Allen Wrench (T-B)

Warnings

Tipover Warning: The use of tipover restraints may reduce the risk of tipover but does not eliminate it completely.
Choking Hazard: This product contains small parts and is not suitable for children under 3 years. Adult supervision is required.

Product Usage Instructions

Apply Rubber Pads (D) to the underside of the Base (C).
Mount the Column (A) to the Base (C) using the M6x10mm Screws (S-C) and tighten with the 4mm Allen Wrench (T-A).
Attach the VESA Plate (B) to the Column (A) using the Knob (S-A), Metal Washer (S-B), and Plastic Washer (S-E).

Option A: Flat Back Monitor

```
* Insert the M4x8mm Screws (M-A) or M4x12mm Screws (M-B) into the top two holes of the monitor, leaving 3mm of thread exposed.
```
- Hang the monitor over the slots in the VESA Plate (B) and insert the screws into the bottom two holes.
- Tighten the screws using a Phillips screwdriver.

Option B: Curved Back Monitor

```
* Insert the M4x30mm Screws (M-C) with Spacers (M-D) into the top two holes of the monitor, leaving 3mm of thread exposed.
```
- Hang the monitor over the slots in the VESA Plate (B) and insert the screws with spacers into the bottom two holes.
- Tighten the screws with a Phillips screwdriver.
Adjust the height of the monitor by loosening the Knob (S-A) and tightening it at the desired height.
Adjust the tilt joint using the 5mm Allen Wrench (T-B). Note: Hold the monitor when adjusting the height.

WARNING! If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

TOOLS NEEDED

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.

ASSEMBLY STEPS

STEP 1
Apply Rubber Pads (D) to underside of Base (C).
STEP 2
Mount Column (A) to Base (C) using M6x10mm Screws (S-C) and tighten with 4mm Allen Wrench (T-A).
STEP 3
Attach VESA Plate (B) to Column (A) using Knob (S-A), Metal Washer (S-B), and Plastic Washer (S-E).
STEP 4
- OPTION A: Flat Back Monitor
  Insert M4x8mm Screws (M-A) or M4x12mm Screws (M-B) into top two holes of monitor, leaving 3mm of thread exposed. Hang monitor over slots in VESA Plate (B), insert screws into bottom two holes, then tighten using a Phillips screwdriver.
STEP 4 (continued)
OPTION B: Curved Back Monitor
Insert M4x30mm Screws (M-C) with Spacers (M-D) into top two holes of monitor, leaving 3mm of thread exposed. Hang monitor over slots in VESA Plate (B), insert screws with spacers into bottom two holes, then tighten with a Phillips screwdriver.
STEP 5
Adjust monitor height by loosening Knob (S-A), then tighten at desired height. Adjust tilt joint using the 5mm Allen Wrench (T-B).
- NOTE: hold monitor when adjusting height.

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 11/03/2022 REV1
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.

309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com. Chat live with an agent! AVG.
RESOLUTION TIME (within office hrs): < 15 M
help@vivo-us.com.
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com.

SKU: STAND-V001D

Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. Instruction Manual https://vivo- us.com/products/stand-v001d.
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST