CHACON DiO 54791 1 Channel 433MHz Remote Control Instruction Manual
- June 5, 2024
- CHACON
Table of Contents
- CHACON DiO 54791 1 Channel 433MHz Remote Control
- Changing the battery in your remote control
- Linking the remote control with a DiO 1.0 module, socket
- Linking the remote control with the receiver
- Deleting the link between the remote control and a DiO receiver
- Use
- Troubleshooting
- Technical specifications
- Supplementing your installation
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CHACON DiO 54791 1 Channel 433MHz Remote Control
Changing the battery in your remote control
- Open the small compartment at the back of the remote control.
- Replace the old battery with a new 3V CR2032 battery.
Warning: Risk of explosion if the battery is not replaced correctly.
Replace only with the same type or an equivalent type.
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death. Keep new and used batteries away from children. If the
battery compartment does not close securely, stop using the product and keep
it away from children. If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate medical attention.
Linking the remote control with a DiO 1.0 module, socket
This product is compatible with all DiO 1.0 peripherals operating under the
DiO 1.0 radio protocol, and with the DiO Smart Home main unit for control
through your smartphone.
Using the DiO main unit, you can control your home wherever you are through
your smartphone. For more information visit:
www.chacon.com.
Linking the remote control with the receiver
- Connect the receiver (module, socket).
- Bring the remote control close to the DiO 1.0 receiver and press the receiver learn button (see receiver manual); the receiver LED flashes.
- Press the ‘I’ button on the remote control to link them.
- The lamp connected to the module/socket flashes twice to confirm the link and the LED stops flashing.
Deleting the link between the remote control and a DiO receiver
If the remote control memory is full or if you want to delete a receiver:
- Bring the remote control close to the receiver to be deleted and press the receiver learn button (socket, module, doorbell, bulb – see product manual); the receiver LED flashes.
- Press the ‘OFF’ (O) button of the remote control to be deleted; the lamp flashes twice to confirm the deletion and the LED of the receiver stops flashing.
Use
ON/OFF control: Press the ‘I’ button of the remote control once to turn
your light, device, roller shutter, etc. on, or the ‘O’ button once to turn it
off.
Dimmer (only with a dimmer module, socket or bulb): Press the ‘I’ button
of the remote control twice; the brightness starts to increase/decrease; press
‘I’ again to stop the increase/decrease.
When you turn off the light with the ‘O’ button, the last brightness level
selected will be retained in the receiver memory.
DiO 1.0 receivers (lighting module, shutter module, socket, bulb, etc.) can be
controlled individually or in conjunction with other receivers (e.g.: a DiO
switch closes the shutter linked to a DiO shutter module and at the same time
turns on the lamp connected to the lighting module, and the DiO remote control
turns the lamp on and off individually).
Troubleshooting
The receiver is not activated when the remote control is pressed:
- Check the polarity of the battery and/or that it is not flat.
- Make sure that the remote control is linked to the receiver and that the receiver is connected correctly.
- Check the status of the receiver memory (see receiver manual).
Important: The range between the receiver and the remote control is 50 m, but this may be reduced by the thickness of the walls or a currently wireless environment.
A minimum distance of 1-2 m is necessary between two DiO receivers (module, socket and/or bulb). Do not use in a damp location.
Technical specifications
- Protocol: DiO 1.0
- Frequency: 433.92 MHz
- Transmission range: 50 m (in free field)
- Lithium battery: CR2032 3V (included)
- Number of channels: 1
- Dimensions: 84 x 36 x 10 mm
- Indoor use (IP20). Do not use in a damp environment.
Supplementing your installation
Supplement your installation with DiO solutions to control your heating,
lighting, roller shutters, or garden, or to use video surveillance to keep an
eye on what is happening at home.
Easy, high-quality, scalable and economical…learn about all of the DiO
Connected Home solutions at www.chacon.com.
Recycling
In accordance with European WEEE directives (2002/96/EC) and directives
concerning accumulators (2006/66/EC), any electrical or electronic device or
accumulator must be collected separately by a local system specialising in the
collection of such waste. Do not dispose of these products with ordinary
waste. Check the regulations in force. The logo shaped like a waste bin
indicates that this product must not be disposed of with household waste in
any EU country. To prevent any risk to the environment or human health due to
uncontrolled scrapping, recycle the product in a responsible manner. This will
promote the sustainable use of material resources. To return your used device,
use the return and collection systems, or contact the original dealer. The
dealer will recycle it in accordance with regulatory provisions.
CHACON declares that device 54791 conforms with the requirements and
provisions of Directive RED 2014/53/EU.
The complete text of the EU declaration of conformity is available at the
following Internet address:
www.chacon.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>