SCARLETT SC-HC63C10DBL Hair Clipper Set Instruction Manual

SCARLETT SC-HC63C10DBL Hair Clipper Set

DESCRIPTION

1. Blades
2. Blade adjustment lever
3. Housing
4. On/Off switch
5. Hanging loop
6. 4 detachable combs
7. Oiler
8. Brush for blades cleaning

SPECIFICATION

IMPORTANT SAFEGUARDS

• Please read this instruction manual carefully before use and keep in a safe place for future reference.
• Before switching on the appliance for the first time please check if the technical specifications indicated on the unit correspond to the mains parameters.
• For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes than described in this instruction manual.
• Do not use outdoors.
• Always unplug the appliance from the power supply before cleaning and when not in use.
• To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids. If it has happened DO NOT TOUCH the appliance, unplug it immediately and check in a service center.
• Do not take this product to a bathroom or use near water.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliances by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not leave the appliance switched on when not in use.
• Do not use other attachments than those supplied.
• Do not operate after malfunction or cord damage.
• Do not attempt to repair, adjust or replace any parts of the appliance. Check and repair the malfunctioning appliance in the nearest service center only.
• Keep the cord away from sharp edges and hot surfaces.
• Do not place or store the appliance where it can fall or be pulled into a tub or sink.
• Do not pull, twist, or wrap the power cord around the appliance.
• Never insert any objects into openings in the appliance housing.
• Do not put operating appliance on any surface, it may cause injury or damage.
• Do not use the appliance with a damaged comb, or with teeth missing from the blades as injury may occur.
• If the product has been exposed to temperatures below 0ºC for some time it should be kept at room temperature for at least 2 hours before turning it on.
• NOTE: KEEP THE BLADES OILED.
• Do not use the hair clipper when the skin is infected.
• Do not use the hair clipper on animals.
• The manufacturer reserves the right to introduce minor changes into the product design without prior notice, unless such changes influence significantly the product safety, performance, and functions.
• Production date mentioned on the unit and/or on the packing materials and documentation.

BLADE ALIGNMENT

• Your clipper was carefully examined to ensure that the blades were oiled and properly aligned before leaving our factory.
• Blades must be realigned if they were removed for cleaning or after replacement.
• To realign the blades, simply match the teeth of the upper and lower blade up, point for point.
• End of the top blade teeth should be approximately 1.2 mm back from lower blade. Compare your clipper blades with the sketch (pic.1).
• If blade alignment is incorrect, add a few drops of oil to the blades, switch on the clipper for a few moments, switch off and unplug. Loosen screws slightly and adjust. Tighten screws after the blade is aligned.

OILING

• To maintain your clipper in peak condition, the blades should be oiled after every haircut.
• Do not use hair oil, grease, oil mixed with kerosene, or any solvent.

BLADE LEVER

• The lever located to the left of the blades, allows easily adjust cut hair length while clipping.
• The lever adds versatility to your clipper by allowing you gradually change the closeness of your cut without an attachment comb.
• When the lever is in the uppermost position, the blades will give you the closest cut and leave the hair very short. Pushing the lever downwards gradually increases the cutting length.
• In its lowest position, the lever will leave the hair approximately the same length as a №1 (3mm) comb.
• The lever will also extend the use of your blades since a different cutting edge is used in each setting.
• In addition, if extremely heavy hair cutting has jammed the blades, it will help you to remove hair that has become wedged between the two blades without removing the blades.
• While the clipper is running rapidly move the lever from “close cut” to “longer cut” a couple of oftimes. Do this each time after you have finished using your clipper to keep the blades free of cut hair.
• If this does not help and clipper stops cutting, the blades are dulled. Replace them with new blades.

INSTRUCTIONS FOR HAIRCUTTING

• Before starting the hair cut inspect the clipper, making sure that there is no oil between the cutting blade teeth, switch the unit on to distribute the oil between the blade teeth and to check running smoothness. Wipe off any excess oil. This should be done after each use. While using the unit, untwist the cord from time to time to avoid tangling.
• Before cutting always comb the hair thoroughly first.

DETACHABLE COMBS

Attachment comb

№

| Hair length mm/inches
---|---
№1| 3 (1/8)
№2| 6 (1/4)
№3| 9 (3/8)
№4| 12 (1/2)

• Each comb attachment is marked accordingly on its outside middle surface.
• To attach a comb, hold it with its teeth upward and slide onto and along the clipper blade until the front of the comb firmly seats against the clipper blade.
• When you use the clipper for the first time, cut only small portions of hair.
• For even cutting do not force the clipper. Also remember to comb the hair more frequently to remove trimmed hair and check for uneven strands.
• It is recommended that you start the haircut by choosing the maximum hair length, and then gradually reduce the length setting.
• In order to obtain the most effective result move the device in the direction opposite to the direction of hair growth. Since hair in different head segments grows in different directions, you need to move the device in different directions as well (up, down, or crosswise). See Figures 2.1-2.8.
• In order to obtain a good haircut for wavy, rare or long hair, use a comb to direct the cutting block of the device. See Figure 2.6.

CARE AND CLEANING

• Switch off the appliance and unplug it.
• Clean and oil the appliance after each use.
• Remove cut hair from the clipper with the brush enclosed.
• Wipe the clipper with a dry soft cloth.
• Oil the blades as mentioned above.

STORAGE

• Keep the appliance in a dry place.
• You may hang the cutter by providing loop.
• The blades must be oiled for the storage period.

DISPOSAL

The symbol on the unit, packing materials and/or documentation means used electrical and electronic units and the batteries should not be toss in the garbage with ordinary household garbage. These units should be pass to a special receiving point. For additional information about actual system of garbage collection address to the local authority. Valid utilization will help to save valuable resources and avoid negative work on the public health and environment which happens with incorrect using garbage.

www.scarlett.ru

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>