Chacon 34034 Wireless Alarm with Voice Warner User Manual

June 5, 2024
CHACON

Chacon 34034 Wireless Alarm with Voice Warner

Package Included

Registering the guarantee
To register your warranty, fill in the online form at www.chacon.com/warranty

Product overview

  1. Siren

  2. LED 5

  3. Chime mode

  4. Zone 1 button

  5. LED 1

  6. LED 3

  7. Zone 3 button

  8. Volume

  9. LED 6

  10. Arming and disarming button

  11. Zone 2 button

  12. LED 2

  13. LED 4

  14. Zone 4 button

  15. Micro

  16. LED indicator

  17. Motion detector

  18. Motion detector

  19. LED indicator

  20. Arm

  21. Disarm

  22. Emergency button

Introduction

Thank you for using this product.

  • Please read all instructions carefully before using the product.
  • Do not attempt to disassemble or repair the product yourself, as this will invalidate the warranty.
  • Remove the tab from each product before using them.

Battery installation

• Portable alarm (central alarm)

  1. Turn the unit over and slide the cover down to access the battery compartment.
  2. Insert the batteries, making sure that the polarity is correct (+/-)
  3. Close the compartment.

Note: If lights 1, 2, 3 and 4 remain on at the same time, it means that the battery is low. Please change it as soon as possible.

• Motion detector

  1. Turn the unit over
  2. Using a crosshead screwdriver, remove the screw on the back of the motion detector.
  3. Using a flathead screwdriver, separate the two parts to access the battery compartment.
  4. Insert the batteries, making sure that the polarity is correct (+/-)
  5. Close the compartment and seal it with the screw.

Note: When the battery is low, the LED will flash twice every 15 seconds. For optimal use, we recommend that you test the device every 3 months.

• Opening detector

  1. Take the largest part of the detector and turn it over.
  2. Using a flathead screwdriver, separate the two parts to access the battery compartment.
  3. Insert the batteries, making sure that the polarity is correct (+/-)
  4. Close the compartment.

• Remote control

  1. Turn the remote control over
  2. Using a small crosshead screwdriver, remove the screw on the back of the remote control.
  3. Separate the two parts to access the battery compartment.
  4. Lift the metal part with the «+» marking before inserting the CR2032 battery
  5. Insert the batteries, making sure that the polarity is correct (+/-)
  6. Close the remote control compartment and seal it with the screw.

Note: If the indicator led doesn’t light up or dims when you press the button, please replace the batteries.

Button’s explanations: central alarm

On this alarm there are various buttons. Let’s go through them quickly for ease of use.

| Buttons 1,2,3 and 4 represent zones. Each zone can correspond to different rooms in your house/apartment/business so that you can detect where the intrusion is coming from.
Example; Zone 1 = Bedroom, Zone 2 = Garage, Zone 3 = Veranda… and so on…
---|---
| By combining your accessories on this chime mode, you will receive a musical notification when the opening or motion detector is triggered.
This can be useful when you run a business to know when someone is entering or leaving your shop.
Note: You can choose from 32 different melodies
| Arming and disarming your alarm.
| The side button has several functions:

  • Volume: decrease, increase or mute (vibrate)
  • Change melodies (chime mode)
  • Record a voice message (only in disarmed mode)

Note: Each element of this kit can be associated to only one zone (max 10/ zone).
You can also buy a second kit and associate it with your current kit. Being 100% compatible, you will be able to associate the same opening detector with several alarm control units. This allows you, for example, to leave one alarm in your living room and another in your bedroom

Motion detector

When you open the detector, you will see a switch with the letters «T» and «S» written. This allows you to choose between two monitoring modes.

  • “T” mode: This is the energy saving mode. As soon as the detector detects a movement, the alarm sounds. Then starts the sleep mode. If within 60 seconds a second movement is detected, the detector will count down 60 seconds before a second alarm can be issued.
  • “S” mode: As soon as the detector detects movement, the alarm sounds. Then it will take about 60 seconds for another alarm to sound. (Recommended mode).

Remote control button

  • Padlock closed: Alarm on.
  • Padlock open: Alarm deactivated. However, you still receive a voice alert (see point 8)
  • SOS Mode / Home Mode: When you press either button, the alarm will be activated directly. You will have to press the button on the remote control or on the central alarm to deactivate it.

Synchronisation of devices

  1. Opening detector :
    a. Press the button for the zone of your choice (1,2,3,4) until you hear a «beep».
    b. Separate the two ends of the opening detector.
    c. A beep will follow to let you know that the synchronization was successful.

  2. Motion detector:
    a. Place the face of the motion detector on a table and wait one minute before synchronising.
    b. Press the button of the zone of your choice (1,2,3,4) until you hear a «beep».
    c. Turn the detector over and make a move in front of the detector.
    d. A beep will follow to let you know that the synchronization was successful.

  3. Remote control:
    a. Press the button of the zone of your choice (1,2,3,4) until you hear a «beep».
    b. Press a button on your remote control.
    c. A beep will follow to let you know that the synchronisation was successful.

Note: if you hear a double beep, it means that the pairing didn’t work.

Chime mode

To synchronize your detectors to your central alarm unit in chime mode, the principle is the same as for the synchronization by zone.

  1. Press the «» button, until you hear a «beep».
  2. Synchronize the opening or motion detector by following the steps in point 3.

Wall installation

Central alarm unit (voice alarm)

Thanks to its magnetic plate at the back of the device, you can easily hang it on the doors of your refrigerator, on your microwave… or simply leave it near you on a table or a piece of furniture.

Motion detector

When choosing a location for your motion detector, always ensure that it is placed at a height of 2 metres from the ground and slightly tilted forward. Try to install it in places with the best possible field of vision. (See diagram)

You can opt for installation with double-sided adhesive or with screws.

Tip: Don’t place the detector under a heat source and avoid direct sunlight as much as possible.

Voice recording

  1. Press the side button until you hear a «beep».
  2. Press the button for the area of your choice, you will hear a «beep» to alert you that the message is being recorded.
  3. When you finished your message, press the zone button chosen in the previous point.
  4. You will see the LED for your zone and the one with the two locks flashing.
  5. Press your zone button to listen to your message again.
  6. Satisfied? Confirm and press the side button.

Note: Voice recording notification is only possible in disarm mode.

Unpairing devices from a zone

  1. Press the zone button that you want to reset until you hear a «beep».
  2. After the «beep» sound, press again the zone button.
  3. You will hear a different «beep» meaning that the desynchronization has worked.

Resetting the device

  1. Remove the batteries so that the device is completely switched off.
  2. Press and hold the «3» and «4» buttons at the same time for about 10 seconds.
  3. Reinsert the batteries into the device to turn it on. You will hear a «beep» indicating that the reset was successful.

Note: After restoration, all added accessories will be deleted.

Safety advice

  • Don’t mix new and used batteries.
  • Please use only the type of battery specified in the manual.
  • Don’t leave used batteries lying around in the unit, as this may damage the unit.
  • Don’t place the control panel against a heat source or where it may be exposed to direct sunlight, rain or strong light.
  • The unit isn’t waterproof. Don’t expose it to rain or immerse it in water.
  • Don’t attempt to disassemble or repair the product by yourself
  • Please keep these instructions in a safe place.
  • Incorrect use of the battery may damage nearby objects and risk fire or serious injury.
  • Please keep batteries away from children.
  • Recycle used batteries in accordance with environmental protection practices

Technical specifications

  • Central alarm – voice alarm :
    • Alarm volume: ≤ 80dB
    • Battery: 3x AAA 1.5V (not included)

  • Motion detector :
    • Detection distance: 7 m (free field)
    • Detection angle: 90
    • Standby current: ≤ 20uA
    • Alarm current: ≤ 20mA
    • Battery: 2x AAA 1.5V (not included)

  • Opening detector :
    • Standby current: ≤ 3uA
    • Alarm current: ≤ 15mA
    • Battery: 1xCR2032 (Included)

  • Remote control:
    • Battery: 1xCR2032 (Included)
    • Frequency: 433 MHz
    • Operating temperature: -10°C ~ 55°C

| For indoor use only
---|---
| This product must be treated in accordance with European Directive 2002/96/EC with the aim of being recycled or dismantled to minimise its impact on the environment. For further information, please contact your local or regional authorities.
| Hereby, Chacon declares that the radio equipment type 34034 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.chacon.com/conformity

Support
www.chacon.com/support

Documents / Resources

| Chacon 34034 Wireless Alarm with Voice Warner [pdf] User Manual
34034, Wireless Alarm with Voice Warner
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals