Chacon 34045 All-in-One Alarm User Manual
- June 5, 2024
- CHACON
Table of Contents
- Introduction
- Synchronization of devices
- Wall installation of the control unit
- Mode on the remote control
- Setting up the personal code
- The functionality of the keypad
- Reset pairing
- Problem-solving
- Add a device to your existing alarm
- Safety advice
- Technical specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
34045 All-in-One Alarm
User Manual
Registering the guarantee
To register your warranty, fill in the online form at
www.chacon.com/warranty
Product overview
1 | Motion detector |
---|---|
2 | Speaker |
3 | Flashing LED |
4 | Pairing button |
5 | « On » button |
6 | « Off » button |
7 | « Away » mode |
8 | « Home » mode |
9 | LED indicator |
10 | Magnetic part |
11 | Keypad |
Introduction
Thank you for using this product.
- Please read all instructions carefully before using the product.
- Don’t attempt to disassemble or repair the product yourself, as this will invalidate the warranty.
Battery installation: Central alarm unit with motion detector
- Using a crosshead screwdriver, remove the screw from the back of the motion detector.
- Slide the cover down to access the battery compartment.
- Insert the batteries, ensuring correct polarity (+/-).
- Close the compartment with the cover and screw.
Note: When the battery is low, the LED indicator will flash slowly (3s/flash)
Battery installation: remote control
- Using a crosshead screwdriver, remove the screw on the back of the remote control.
- Slide the cover to the left to access the battery compartment.
- Insert the battery, making sure that the polarity is correct (+/-)
- Close the compartment with the cover and screw.
Battery Installation: Door Opening Sensor
- Using a crosshead screwdriver, remove the screw on the front of the opening detector
- Slide the cover down to access the battery compartment.
- Insert the battery, ensuring correct polarity (+/-)
- Close the compartment with the cover and screw.
Battery installation: remote keyboard
- Use a flat screwdriver to separate the two parts of the keyboard.
- Insert the battery taking care to respect the polarity (+/-)
- Close the compartment.
Synchronization of devices
-
Using a screwdriver, open the battery compartment of the main unit.
-
Press and hold the learn button until you hear a «beep». The unit enters pairing mode. (see diagram)
a. Opening detector: Separate the two parts of the opening detector to send a signal to the main unit. You will hear a «beep» sound to indicate that the pairing was successful.
b. Remote control: Press any button on the remote control. You will hear a «beep» sound to indicate successful pairing.
c. Remote Keyboard: Press any button on the remote keyboard. You will hear a «beep» sound to indicate successful pairing. -
To exit pairing mode, press and hold the learn button for 3 seconds. You will hear a double «beep».
Wall installation of the control unit
- Once you have installed the batteries, choose a location for your motion detector.
- Fix the bracket to the wall using the supplied dowels and screws.
- Fit the sensor onto the bracket and then choose the best angle for the sensor to have the best possible field of view.
Recommended installation height:
Maximum 160cm and minimum 30cm.
NOTE: Adjust the installation angle so that it faces downwards.
Mode on the remote control
The remote control has an «On» button to activate the alarm and an «Off»
button to deactivate it.
On the side of the remote control, there are two inscriptions «HOME» and
«AWAY».
a) Home mode: When you select «HOME» mode with the switch, it means that you
are at home and don’t want to be disturbed. Slide the switch on the remote
control marked «HOME» and press the «On» button.
b) AWAY mode: When you select the «AWAY» mode with the switch, it means that
you are leaving your home and want to turn off your alarm. Slide the switch on
the remote control marked «AWAY» and press the «On» button
NOTE: In «home» mode, all motion detectors are disabled.
Setting up the personal code
Once you have placed your batteries, you have 15 seconds to choose a four-
digit code. If you have not had time to enter your personal code, the code
1234 will be saved by default.
Note: Each time you install batteries, you will need to set up your
4-digit code again.
The functionality of the keypad
a) HOME Mode: Enter your 4-digit code, then press the «1» button. You will
hear a «beep» to indicate that the alarm will enter «home» mode after 30
seconds.
NOTE: In this case, the motion detection function is disabled. Only the
opening detector will trigger an alarm. This mode is also available on the
remote control.
b) AWAY mode: Enter your 4-digit code, then press the «2» button. You will
hear a «beep» to indicate that the alarm will enter the «Away» mode after 30
seconds.
NOTE: In this case, if someone opens the door or window equipped with the
opening detector or enters the field of vision of your motion detector, the
alarm will be triggered. This mode is also available on the remote control.
c) Emergency mode: Press buttons 1 and 4 simultaneously in case of emergency.
An alarm will sound without a time limit to scare off intruders.
Reset pairing
In order to reset your entire alarm, remove the batteries from your device. Then press and hold the learning button (see diagram point 1.). When you reinsert the batteries, you will hear two «beeps» indicating that the reset was successful.
Problem-solving
-
False alarms from the main unit
a) Check that there are no animals near the motion detector.
b) In hot weather, moving shadows may also activate the alarm. Also, ensure that the detector is not installed near a radiator or heat source.
c) Check that there are no devices with strong electromagnetic fields near the door/window sensor. Strong electromagnetic fields can cause false alarms. -
The main unit doesn’t receive a signal from the transmitter
a) Check if the pairing between the transmitter and the main unit was successful.
b) If the pairing was successful, check the battery voltage of the main unit and transmitter. Low voltage will result in product failure. -
No alarm sounds after a detection
a) Check if the low battery indicator is flashing (please replace the batteries immediately).
b) If the unit is armed and set to HOME mode and the PIR sensor detects an intrusion, the alarm will not sound. The PIR sensor is disabled in HOME mode. Check if the main unit is installed correctly.
Add a device to your existing alarm
We have created a 100% compatible alarm system to meet your needs.
Here, we offer accessories that can work alone but also as a kit. This allows
you to personalize your alarm and to associate several accessories but also
several alarms between them. For example, when a person triggers the opening
detector, all your alarms will sound. You can deactivate your alarm using the
code units, remote control or the remote keyboard.
More information on our website: https://chacon.com/fr/
Compatible products: 34035, 34036, 34038, 34043, 34044, 34046, 34048
Safety advice
- Don’t mix new and used batteries.
- Don’t mix alkaline, standard (zinc-carbon), or rechargeable (ni-cad, ni-me, etc.) batteries.
- Please use only the type of battery specified in the manual.
- Don’t leave used batteries lying around in the unit, as this may damage the unit.
- Incorrect use of the battery may damage nearby objects and result in fire or serious injury.
- Please keep batteries away from children. If you suspect that batteries have been ingested, seek medical attention immediately. Swallowing the battery can lead to serious consequences; internal burns within 2 hours or death.
- Recycle used batteries in accordance with environmental protection practices
- Don’t place the unit near a heat source, where it may be exposed to direct sunlight, rain, or strong light.
- The unit is not waterproof. Don’t expose it to rain or immerse it in water.
- Don’t attempt to disassemble or repair the product yourself.
- Please keep this manual in a safe place.
- The reception distance may be affected if a strong interference signal exists in the area of use.
Technical specifications
- Can be switched on or off remotely via the controls provided
- Easy to install
- Compatible products: 34035, 34036, 34038, 34043, 34044, 34046, 34048
- Motion detector:
- Detection distance: 8 m (free field)
- Detection angle: 100
- Alarm volume: 100 dB
- Standby current: ≤ 350uA
- Alarm current: ≤ 150mA
- Battery: 3x AA 1.5V (not included)
- Remote control:
- Battery: 1x CR2032 (included)
- Standby current: ≤ 3uA
- Alarm current: ≤ 25mA
- Opening detector:
- Battery: 1x CR2032 (included)
- Standby current: ≤ 3uA
- Alarm current: ≤ 15mA
- Remote keyboard:
- Battery: 2xAAA 1,5V (not included)
- Standby current: ≤ 3uA
- Alarm current: ≤ 15mA
- Box content: Motion detector + 1 remote control + remote keyboard + door opening detector + battery (2x) + manual
Support www.chacon.com/support
For indoor use only
This product must be treated in accordance with European Directive 2002/96/EC
with the aim of being recycled or dismantled to minimize its impact on the
environment. For further information, please contact your local or regional
authorities.
Hereby, Chacon declares that the radio equipment type 34045 is in compliance
with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
www.chacon.com/conformity
v1 210809
Chacon S.A. – Avenue Mercator 2 – 1300 Wavre – Belgium
Made in PRC
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>