Ultraloq U-Bolt Pro V2.4 Installation Guide

June 6, 2024
Ultraloq

Ultraloq U-Bolt Pro V2.4 Installation Guide

Ultraloq U-Bolt Pro V2.4 Installation Guide

Important Notes

  • Do not use a power drill for installation.

  • Install and test the lock with the door open to avoid being locked out.

  • Please read all the instructions before contacting customer support.

  • Please contact customer support before returning the product to the store.

  • DO NOT install the batteries before installing the lock!

  • Follow the instructions in sequential order!

  • This lock is designed for the following operating temperatures:
    Outside Lock Body: -31°F(-35°C) to 158°F (70°C)
    Inside Lock Body: 14°F (-10°C) to 131°F (55°C)

  • Please must use AA Alkaline Battery and don’t use Lithium Battery or Rechargeable Battery.

Statements

To ensure the best service, please register your account at www.u-tec.com/register.html

Ultraloq Terms & Policies

Before using all Ultraloq products, please read all applicable terms, rules, policies and usage provisions found at www.u-tec.com/company/privacy. By using your Ultraloq, you agree to be bound by the U-Tec Privacy Policy.

Need Help?
For technical documents and more Please visit support.u-tec.com

Packing List

Ultraloq U-Bolt Pro V2.4 Installation Guide - Packing
List Ultraloq U-Bolt Pro V2.4
Installation Guide - Packing List

Installation Guide

Installation Video

http://www.u-tec.com/lock/u-bolt_pro/guide

Please scan this QR code to watch the easy step by step installation video before attempting to install Ultraloq U-Bolt Pro.
Or you can also view the website directly. www.u-tec.com/lock/U-bolt_pro/guide

1. Preparing Door

Check the door’s dimensions.

Step 1
Measure to confirm that the door is between Pia” – 1¾” (35 mm- 45 mm) thick.
Step 2
Measure to confirm that the diameter of the hole is 21/a” (53 mm) or 1½” (38 mm)
Step 3
Measure to confirm that the backset is either 23/a” or 23/).’ (60 mm or 70 mm).
Step 4
Measure to confirm that the diameter of the hole in the door edge is 1″ (25 mm).
Step 5
Measure to confirm the depth of the hole in the frame is at least 1″(25mm).

Ultraloq U-Bolt Pro V2.4 Installation Guide - Preparing
Door

If you have a new door, please drill the holes according to Drill Template.

2. Installing Bolt and Strike

Step 1

Install Bolt into the door. Make sure the UP ↑ icon goes up.

Note: Bolt is set for 23/a” backset initially. It can be adjusted to 2 3/,/’ if needed. To adjust it please make sure the bolt is retracted, then, press it, twist and pull it or push it to your desired length.

Step 2
Install Strike into the door frame.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Installing Bolt and
Strike

3. Installing Exterior Assembly

Step l
Keep Bolt retracted and the cylinder tail piece horizontal. Install Exterior Assembly. Please do not insert the mechanical key during installation.
Step 2
Align its two sticks with two holes on Bolt. The cable goes through the hole below Bolt.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Installing Exterior
Assembly

if your door has a 11/{(38 mm) bore hole, remove the spacer as shown.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Remove the spacer as
shown

Ultraloq U-Bolt Pro V2.4 Installation Guide - Install
Switch

4. Installing Interior Assembly Mounting Plate

Step l
Route the cable through the hole on Interior Assembly Mounting Plate.

Step 2
Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Installing Interior Assembly
Mounting Plate

5. Installing Interior Assembly

Step 1
Remove the battery cover of the Interior Assembly.

Step 2
Insert the connector of the cable to the socket on Interior Assembly. Press the connector in firmly until it is completed seated.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Insert the connector of the
cable to the socket on interior assembly

Step 3
Rotate the knob and keep it in a vertical position to stay unlocked.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Rotate the knob and keep it in
a vertical position

Step 4
Attach Interior Assembly to Mounting Plate and tighten 2 Screws E.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Attach interior Assembly to
mounting plate and tighten 2 screws E

6. Installing the Batteries and Performing the Door Handing Process

This step will teach your lock the orientation of your door and is crucial to lock operation.

Step l
Rotate the knob and keep it in a horizontal position to stay locked.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Rotate the knob and keep it in
a horizontal position to stay locked

Step 2

Insert 4 AA Alkaline Batteries.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Insert 4 AA Alkaline
Batteries

Note: Any fingerprint or code can unlock U-Bolt Pro in Factory Default Mode.

Step 3
Install battery cover.

User Guide

User Guide Video
Please watch our easy step by step User Guide video before attempting to use your Ultraloq U-Bolt Pro Smart Lock.

Or you can also view the website directly. www.u-tec.com/lock/U-bolt_pro/guide

1. Product Overview

1.1 Exterior

Ultraloq U-Bolt Pro V2.4 Installation Guide - Product
Overview

Anti-peep Keypad

Used to enter the code and unlock from outside.

Advanced Fingerprint Reader
Used to verify your finger and unlock from the outside.

Backup Key Hole
Used to insert the key to unlock in emergency situations.

Micro USB (SV)
Used to connect power bank to activate the lock when battery runs out.

Tri-color LED Indicator
Shows you authorized or denied access, Bluetooth connectivity status, battery status etc.

Ultraloq Button
Used to lock from the outside, illuminate the keypad for code entry and confirm previous operation etc.

1.2 Interior

Ultraloq U-Bolt Pro V2.4 Installation Guide - Interior

Reset Button
Used to reset the lock to Factory Default settings.

If the lock was paired to App, please must click “Delete” to remove the device from App.

Battery Compartments
Used to insert 4 AA alkaline batteries.

Note:
Lithium batteries may have a longer life, but when they begin to fail, they fail quickly. We don’t recommend them because they don’t give you a lot of time to change your batteries before the lock is completely dead. Please don’t use any Rechargeable Battery.

Battery Cover
Used to cover batteries and product label.

Knob
Used to unlock and lock the door from inside.

LED Indicator
Turns red when door is unlocked.

1.3 Low Battery Alarm

There will be low battery alert on the lock and App when battery is low. Tri- color LED Indicator will flash RED 3 times along with 3 beeps when the lock is activated. Please replace batteries.

2. Lock Setup

Ultraloq U-Bolt Pro V2.4 Installation Guide - QR Codehttps://www.u-tec.com/app/utec.html

Scan QR code to download the App

Step 1
Scan above QR code to download the App, or search “U-Tec” in App Store (iOS) and Google Play (Android).

Step 2
Open the App, register U-Tec account and log in the account.

Step 3
Make sure the lock is in Factory Default Mode. Turn on Bluetooth on your smartphone, stay near the lock (within 10 feet/ 3 meters) and search the lock in the App.

Step 4
Pair the lock in the App and start to use it.

Note: Please refer to the guide in U-Tec App for more information.

DON’T WANT TO USE THE APP?
Please go to page 15 for programming guide for Standalone Mode.

3. Using Your Lock

3.1 Unlock From Outside
  • User Code

Enter 4-8 digit code and press Ultraloq Button to unlock.

Ultraloq U-Bolt Pro V2.4 Installation Guide - User
Code

  • Fingerprint

Place your finger on Fingerprint Reader to unlock.

Ultraloq U-Bolt Pro V2.4 Installation Guide -
Fingerprint

  • Smartphone

Use your smartphone to unlock. Please refer to the guide in U-Tec App.

Ultraloq U-Bolt Pro V2.4 Installation Guide -
Smartphone

3.2 Lock From Outside

Press Ultraloq Button to lock manually. Enable Auto Lock feature and the lock will relock automatically.

3.3 Unlock From Inside

Rotate the knob to a vertical position to unlock.

3.4 Reset the Lock

Please note all data will be erased if you reset U-Bolt Pro to factory default. If you are using U-Tec App as Owner, please click “Delete and Reset” to remove the lock from your U-Tec Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

3.5 Replace Batteries

Please use 4 high-quality alkaline AA batteries for replacement when the battery is dead.

3.6 5V Emergency Power

Micro USB interface is used to connect regular 5V power bank to activate the lock in case the battery is dead.

3. 7 Emergency Key Override

Emergency Key Override can be used when the battery is dead.

Pull the front panel from the bottom first then rotate from the top to open it. You can see Backup Key Hole inside. Insert the key and rotate to unlock, just like any lock.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Emergency Key
Override

Important Note
Please keep at least one key in secure location outside of your place.

3.8 Enable Or Disable Auto Lock

Enable
Please keep Bolt unlocked and press “1” button for 3 seconds until LED turns green and “1” button blinks.

Disable
Please keep Bolt unlocked and press “0” button for 3 seconds until LED turns green and “0” button blinks.

This can also be set in U-Tec App and Auto Lock timing can be programmed between 10 seconds to 5 minutes. Factory Default timing is 30 seconds.

3.9 Anti-peep Keypad

The lock supports up to 16-digit Vague Code. Just enter any 16-digit code, as long as a correct code is included in what you entered, you can open the door.

Example

User Code: 123456

Vague Code

Ultraloq U-Bolt Pro V2.4 Installation Guide - Vague
Code

3.10 Place Finger

Ultraloq U-Bolt Pro V2.4 Installation Guide - Place
Finger

  1. For a higher recognition rate, please try to cover the Fingerprint Reader completely with your finger, touching the surrounding metal ring.
  2. Make sure that your finger and Fingerprint Reader are clean and dry. For Fingerprint Reader, use a clean, lint-free cloth to wipe off any dirt or debris.
  3. Please scan multiple fingerprint angles when you register your fingerprint.
  4. While scanning your finger, you shouldn’t tap too quickly or move your finger around.
  5. If you have trouble enrolling one finger, try another.
  6. U-Bolt Pro fingerprint sensor has self-study function which the verification rate will be improved after multiple success .

4. Standalone Mode Programming Guide

It is recommended to use U-Tec App to program your lock. If you don’t have a smartphone or don’t want to use the App, you may follow the programming instructions below.

Warning
Standalone Mode is NOT available after the lock is registered in App! Please reset the lock to Factory Default Mode first to program your lock in Standalone Mode.

4.1 Add Admin Code in Standalone Mode

Ad min Code must be created first prior to any other programming. Only one Ad min Code is available.

Ultraloq U-Bolt Pro V2.4 Installation Guide - Add Admin
Code

4.2 Add User Code in Standalone Mode

Ultraloq U-Bolt Pro V2.4 Installation Guide - Add User
Code Ultraloq U-Bolt Pro V2.4
Installation Guide - Add User Code

4.3 Add Fingerprint in Standalone Mode

Ultraloq U-Bolt Pro V2.4 Installation Guide - Add
Fingerprint Ultraloq U-Bolt Pro V2.4
Installation Guide - Add Fingerprint

4.4 Delete Admin and User

Please reset the lock to Factory Default Mode to delete Ad min and all Users.

How to reset the lock in Standalone Mode?
Please use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

FAQ

  1. How to reset U-Bolt Pro?
    Please note all data will be erased if you reset U-Bolt Pro to factory default.

If you are using U-Tec App as Owner, please click “Delete and Reset” to remove the lock from your U-Tec Account, then use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

If U-Bolt Pro is working as Standalone Mode, please use a Reset Needle to push the Reset Button (at the bottom of Interior Assembly) for around 3 seconds until you hear one long beep and two short beeps.

  1. How to control U-Bolt Pro remotely?
    U-Bolt Pro is a Bluetooth enabled smart lock. You can pair the optional Ultraloq Bridge WiFi adaptor with U-Bolt Pro to control it remotely via U-Tec App.

  2. What if I lost the paired smartphone?
    Please go to www.u-tec.com/myutec.html or login U-Tec App via another smartphone to change your U-Tec Account password.

  3. How to adjust the lock orientation of U-Bolt Pro?
    The lock orientation must be adjusted after installation to ensure U-Bolt Pro works properly.
    Solution 1. Adjust the lock orientation on the lock. Go to page 8 for details.
    Solution 2. Adjust the lock orientation via U-Tec App.

  4. How can I unlock U-Bolt Pro if battery runs out?
    There will be low battery alert on the lock and App when battery is low. Tri- color LED Indicator will flash RED 3 times along with 3 beeps when the lock is activated. Please replace batteries.
    Solution 1. Use the backup key to unlock.
    Solution 2. Connect a 5V power bank to activate the lock temporarily.

  5. What’s the difference between Owner, Ad min, Normal User and Temporary User?
    Owner is the person who owns U-Bolt Pro and registers it in U-Tec App originally. Owner has all privileges. Ad min can always unlock via fingerprint, code or App. Admin can add or delete Admin and Users, control all lock settings and view logs. Normal User can always unlock via fingerprint, code or App. Temporary User has limited access within specific time range.

  6. Does U-Bolt Pro work with accessories such as bolt from third party?
    It is recommended to use the original accessories for best performance and stability.

  7. What is the log capacity for U-Bolt Pro?
    U-Bolt Pro supports maximum 1,000 logs. The latest log will replace the oldest one once log is full.

  8. What is the user capacity for U-Bolt?
    U-Bolt Pro supports maximum 50 users and each user can register 1 code and 2 fingerprints.

Keep Your Records

Ultraloq U-Bolt Pro V2.4 Installation Guide - Keep Your
Records

Ultraloq Logo

© 2021 U-Tec Group Inc.
U-Tec and Ultraloq brands and products are trademarked
and protected under law in the United States.
Unauthorized use is prohibited. Ultraloq is sub-brand of
U-Tec Group Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals