ULTRALOQ C1NdRQZ9EUL U Bolt Pro WiFi Smart Lock with Door Sensor Installation Guide

ULTRALOQ C1NdRQZ9EUL U Bolt Pro WiFi Smart Lock with Door Sensor

Important Notes

• Do not use a power drill for installation.
• Install and test the lock with the door open to avoid being locked out.
• Please read all the instructions before contacting customer support.
• Please contact customer support before returning the product to the store.
• DO NOT install the batteries before installing the lock!
• Follow the instructions in sequential order!
• This lock is designed for the following operating temperatures: Outside Lock Body: -31°F(-35°C) to 158°F (70°C)
• Inside Lock Body: 14°F (-10°C) to 131°F (55°C)
• Note: The Exterior Assembly of Ultraloq U-Bolt Pro WiFi is waterproof, but the Interior Assembly is not waterproof at all due to the battery box.
• Please use an AA Alkaline Battery and don’t use a Lithium Battery or Rechargeable Battery.

Packing List

Installation Guide

Installation Video

• Please scan this QR code to watch the easy step-by-step installation video before attempting to install Ultraloq.
• You can also view the website directly. www.u-tec.com/lock/U-bolt.pro.WiFi/guide

Preparing Door

Check the door’s dimensions

Step 1

• Measure to confirm that the door is between Pia” -1¾” (35 mm-45 mm) thick.

Step 2

• Measure to confirm that the diameter of the hole is 21/a” (53 mm) or1½” (38 mm)

Step 3

• Measure to confirm that the backset is either 23/a” or 23/). (60 mm or 70 mm) .

Step 4

• Measure to confirm that the diameter of the hole in the door edge is 1″ (25 mm).

Step 5

• Measure to confirm the depth of the hole in the frame is at least 1″(25 mm).
• If you have a new door, please drill the holes according to the Drill Template.

Installing Bolt and Strike

Step 1

• Install a Bolt into the door. Make sure the UP t icon goes up.

Step 2

• Install Strike into the door frame.

Installing Exterior Assembly

Step 1

• Keep the Bolt retracted and the cylinder tailpiece horizontal.
• Install Exterior Assembly. Please do not insert the mechanical key during installation.

Step 2

• Align its two sticks with two holes on Bolt. The cable goes through the hole below Bolt.
• If your door has a 1½” (38 mm) borehole, remove the spacer as shown.

Installing Interior Assembly Mounting Plate

Step 1

• Route the cable through the hole on the Interior Assembly Mounting  Plate.

Step 2

• Secure Interior Assembly Mounting Plate to Exterior Assembly using Screws D.

Installing Interior Assembly

Step 1

• Remove the battery cover of the Interior Assembly.

Step 2

• Insert the connector of the cable into the socket on the Interior Assembly. When you plug the connector, please make sure the black teeth face up.
• Press the connector in firmly until it is completely seated.

step 3

• Rotate the knob and keep it in a vertical position to stay unlocked.

Step 4

• Attach Interior Assembly to Mounting Plate and tighten 2 Screws E.

Installing the Batteries and Performing the Door Handing Process

• This step will teach your lock the orientation of your door and is crucial to lock operation.

Step 1

• Rotate the knob and keep it in a horizontal position to stay locked.

Step 2

• Insert 4 AA Alkaline Batteries then install the battery cover.
• Note: Any fingerprint or code can unlock U-Bolt Pro WiFi in Factory Default Mode.

Installing the Door Sensor(Optional)

• The door sensor lets you know whether the door is open or closed through the App. When the auto lock is enabled in the App, your Ultralog will only lock itself when the door is closed.
• Please do not mount the door sensor on the kind of metal door that interferes with the magnet inside the door sensor(In this case, the door sensor sticks to the metal door magnetically).
• The door sensor can be installed on a wooden door or the kind of metal door that will not interfere with the door sensor(In this case, the door sensor will not stick to the door magnetically).

Option 1 Installing with Sticker

• Peel off either side of the sticker and push it against the door frame about 10s. Peel off the other side and secure the door sensor on the sticker firmly. Put on the door sensor cover at last.

Option 2 Installing with Screw F

• Push the door sensor against the wall and secure it with Screw F.
• You may need to drill a hole first if the door frame is hard to screw in with Screw F directly. Put on the door sensor cover at last.
• Note: The door sensor should be mounted as close to the edge of your door frame as possible, or within 0 to 1″ (25 mm) from the edge, and as close to the bottom of the extended deadbolt as possible, or within O to 1″(25 mm) from the edge.
• Note: Please refer to the guide in the U-tec App for more information.
• © 2021 U-tec Group Inc.
• U-tec and Ultraloq brands and products are trademarked and protected under law in the United States.

Statements

• To ensure the best service, please register your account at www.u-tec.com/register.html

Ultraloq Terms & Policies

• Before using all Ultraloq products, please read all applicable terms, rules, policies, and usage provisions found at www.u-tec.com/company/privacy.
• By using your Ultraloq, you agree to be bound by the U-tec Privacy Policy.

Need Help?

• For technical documents and more Please visit support.u-tec.com

Documents / Resources

| ULTRALOQ C1NdRQZ9EUL U Bolt Pro WiFi Smart Lock with Door Sensor [pdf] Installation Guide
C1NdRQZ9EUL U Bolt Pro WiFi Smart Lock with Door Sensor, C1NdRQZ9EUL, U Bolt Pro WiFi Smart Lock with Door Sensor, WiFi Smart Lock with Door Sensor, Smart Lock with Door Sensor, Door Sensor, Sensor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>